Search Documents

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008

By Samantha Smith

Nautilus is completing the world's first environmental impact assessment (EIA) of seafloor mineral extraction and Nautilus has gained extensive experience conducting environmental studies in subsea environments. Nautilus is currently working on the Solwara 1 Project in the Bismarck Sea, Papua New Guinea, where high grade seafloor massive sulfide deposits lie at ~1600 m water depth. Conducting an EIA in the deep sea presents some interesting and exciting challenges. Seafloor studies commenced in December 2005 using a remotely operated vehicle (ROV) fitted out with highly specialized scientific equipment to conduct water quality, sediment, biological and oceanographic studies. During 2007 and 2008, Nautilus launched two two 30-day ROV programs dedicated to environmental baseline studies and during this campaign, over 550 biological, sediment and water samples were collected and over 20,000 seafloor observations were logged. On board specialists included an international team of experts in the field of deep sea marine science. Collaboration between industry and scientific research institutions allows data to be collected for the EIA but also provides an extraordinary opportunity for researchers to access sites that might otherwise remain unobtainable to science. This presentation will review the studies conducted as part of this exciting project. Keywords: Seafloor Massive Sulfides, Environmental Impact Assessment

Jan 1, 2008

By Harvey W. Parker

The underground industry is challenged by many complex technical and non-technical issues and risks. The most obvious of these are the traditional technical issues that we usually try to address with risk management techniques. However, there are many other non-technical risks that our projects face on a daily basis which we often fail to fully recognize or appreciate. This paper addresses some of the less-technical broad-based risks in order to put them into perspective with the technical risks we face day to day in underground planning, design and construction. The good news is that Risk Management techniques are not always about bad things. For obvious reasons Risk Management is always thought of in terms of the ?downside? of risk (i.e., the identification and mitigation of things that can go wrong). On the contrary, there is an ?upside? of things that might go better than expected. Fortunately, if a deliberate effort is made, the same principles and techniques that our industry uses in Risk Management can be applied toward identifying and quantifying the Opportunities and Benefits that might occur. In this way, the process of conducting risk management programs can not only identify the downside risk but can be used to identify and direct projects to take advantage of the upside of uncertainty (i.e., Opportunities as they arise). This beneficial aspect of risk management programs will be highlighted in this paper together with the importance of the non-technical issues.

Jan 1, 2008

Sampling systems are never perfect. They all have some bias and give variable sampling errors. The ways of thinking about bias and precision should be different before and after construction (or reconstruction) of a sampling system. Before a sampling system is constructed, the fundamental error variance can be estimated using GyÆs formula or by doing test work on the material to be sampled. The component of sampling variance which varies with the number of sample increments can be computed for the expected patterns of grade variation. The smallness of the bias can be checked using discrete element modelling, by checking that the proposed design complies with clauses in standards, or by copying an existing sampling system that performs well for similar material. After a system has been constructed, sampling precision can and should be monitored directly. Anyone claiming to take responsibility for a sampling system should know its precision. Bias could be checked by comparison to a more accurate sampling system, such as stopped-belt sampling, under conditions where bias seems most likely. However, it is more practical to conduct regular checks that the system is still operating as designed, that the design is still appropriate despite any changes to material flows, and that sample masses are consistent with the correct operation of the sampling system. If precision is not regularly assessed then it should be assumed to be very poor. If a sampling system is not regularly inspected then it should be assumed to be biased.

Jan 1, 2008

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By F. Calizaya

The Western Mining Training and Translation Center is a consortium of four universities devoted to developing educational and training projects to reduce the incidence/accident rates in the mining industry. The center consists of Missouri University of Science and Technology, Montana Tech, the Colorado School of Mines and the University of Utah. It is fully funded by the National Institute for Occupational Safety and Health (NIOSH). The center manages 15 educational projects and one translation project. Hazard Identification and Risk Assessment (HIRA) for Small Mines is an educational project managed by the University of Utah. The objectives of this project are to identify critical mine hazards, assess risks; outline procedures to reduce accident/incident rates in small mines in the western United States and to train mine workers and super-visors on HIRA in each participating mine. To accomplish these objectives, the HIRA personnel visited 15 small mines in Utah, Colorado, Nevada and California. At these mines, most operators were employing independent contractors to perform several tasks ranging from drilling, blasting and mucking of rock at the work site to hauling ore to a processing plant. The operation of diesel-powered equipment was one of the major tasks performed by the contractors. This article presents three case studies in which contract workers performed a number of tasks with no reportable incidents but did so unsafely. It also highlights the training received by most contractors, the constraints imposed upon them and the safety hazards to which they are exposed most frequently.

Jan 1, 2008

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

By B. Wasmund, M. Y. Solar, I. Candy

The nickel laterite industry is divided into two camps when it comes to the grade of the ferronickels produced. One group, led by Falcondo and Cerro Matoso, markets high-grade ferronickels in the range of 35 to 40% nickel, while another group, led by SLN and the Japanese smelters, favour lower grades in the range of 20 to 25%. Because the ores processed by these smelters vary widely in terms of nickel content and iron to nickel ratios, it is probably more accurate to classify these smelters in terms of their iron recovery: Falcondo and Cerro Matoso smelt at lower reduction potentials and thus recover only 15 to 30% of the iron in their ores, while SLN and the Japanese smelters are very reducing and recover 45 to 65% of their iron. Low reductions generally imply higher slag losses and lower nickel recoveries, but also lower power and reductant requirements; higher reductions, the reverse. The question is, therefore, whether an economically optimum ferronickel grade exists for processing any given ore. This paper proposes a methodology for determining this optimum grade and concludes that nickel laterite smelters should favour low reductions and production of high-grade ferronickels.

Jan 1, 2008

By Jodi Roberts, Curtis Deredin, Jean-Guy Paulin

"Since the establishment of the Six Sigma quality improvement program in 2001, several projects have been successfully carried out in the copper-lead, zinc, copper separation, lead upgrading and bulk flotation circuits in the Brunswick Concentrator.This paper provides an update on the process improvement initiatives that have taken place since 2004 using the Six Sigma methodology:•,The recirculation of warm water to the flotation circuit (to save on energy costs)•,Installation of a heat recovery tower to recuperate the heat lost from the zinc dryers•,Installation of an extra row of cleaner-scavenger cells for the copper-lead circuit for extra capacity, and a new reagent scheme for the copper separation circuit that have increased copper and lead recoveries.INTRODUCTIONThe Brunswick Mine Concentrator (Xstrata Zinc Canada) is located near Bathurst, New Brunswick and is one of the world’s largest lead/zinc mines. Milling of ore commenced in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 open pit mine. The concentrator utilizes selective flotation to produce zinc, lead, copper, and bulk lead/zinc concentrates. The ore is a complex massive sulphide, consisting of approximately 20% valuable minerals, 60% pyrite and 20% silicates.Figures 1, 2, and 3 illustrate the historical annual average metallurgical performance and process improvements achieved at Brunswick Mine for the zinc, lead and copper concentrate products. The objective is to continuously direct metallurgical performance towards increasing grades and recoveries while minimizing operating costs."

Jan 1, 2008

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce &apos;greener&apos;, less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of &apos;getting it right&apos; within a thickenerÆs feedwell, the &apos;nerve centre&apos; of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By M. Schafer

The 20 foot diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT-3) has been completed. This paper will summarize aspects of liner design and address the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented.

Jan 1, 2008

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

By V Srinivasan, P Knights, C T. Farrelly

By 2025, with the widespread industry adoption of remote operation centres and advanced analytics, mining companies will find themselves making better, more informed decisions across the value chain. Process automation will drive significant business integration and reorganisation. Better collaboration between functions will make cross value chain optimisation a reality. Wherever possible decisions will be automated, based on analytical models and embedded in an enterprise decision management (EDM) architecture. This will take care of many of the minor day-to-day or the minute-to-minute decisions that consume operators and managers today. More flexible information technologies and architectures derived from the extensions to Web 2.0 and service oriented architecture (SOA) will solve many of the integration issues of today. The ongoing business imperatives for doing more with less people will make true collaboration with partners such as mining contractors, equipment vendors, transport providers, suppliers and maintenance contractors commonplace throughout the industry. All these organisations will be linked in and share common goals and objectives in real-time while providing visibility of internal constraints and available capability, allowing optimised decisions to be made across the extended enterprise. Humans will increasingly move to a more supervisory role and will use advanced collaboration to quickly solve complex abnormal issues that span the value chain out to the extended enterprise. The open collaboration and communication models instilled in the workforce through the widespread use of social networking technologies will drive thought leadership far beyond current æbest practiceÆ thinking. This will encourage the mining industry to extract the business value from rapidly converging fields of study such as environmental sciences, neuroscience, psychology, engineering, information technology and business finance. The future of mining will see a more uniform distribution of data savvy workers between the ages of 20 - 40, forcing a change in current operations. This group will drive the adoption of ubiquitous computing, augmented reality, presence and digital labelling. The enterprise will shift from a relatively static disparate set of functions to a digitally aware, integrated and interactive environment with information available, in context and just in time, to those who need it. The networked virtual enterprise will therefore be a reality.

Jan 1, 2008

By B Snook, G Rollinson, R Fairhurst, R Herrington

Nickel laterites constitute a significant proportion of the worldÆs Ni reserves and are considered environmentally friendly alternatives to traditional sulfide resources. Subsequently they are of increasing significance for exploration and production. To be successfully exploited, however, they require an understanding of the relations between mineralogy, texture, grade and recovery. The development of automated quantitative mineralogy can aid in the characterisation of the ores to help improve extraction and processing methods. Recent developments in hydrometallurgy have resulted in relatively straightforward recovery of Ni in silicate (saprolite and smectite) ores. However, the extraction of Ni from limonitic ores is more complex. It requires a detailed understanding of the iron-hydroxide species and other, potentially interfering, oxide and hydroxide compounds. Particularly the relations between the Ni-bearing goethite and Mn, Al and Cr may adversely affect the economic prospects of an ore. Manganese can adversely affect the selective recovery of Ni and Co from solutions but has also been highlighted as a significant potential by-product (cf, Zhang and Cheng, 2007). Aluminium hydroxides can be significant acid consumers leading to an increased expense of extraction (Johnson, Cashmore and Hockridge, 2005). Chromite is resistant to acid attack, but chromium in goethite may adversely affect the dissolution leading to a retention of Ni (McDonald and Whittington, 2008). This study presents an investigation of oxide and hydroxide species in laterites using QEMSCAN« EDS/SEM-based automated quantitative mineralogy. Samples were collected from Turkey (¦aldag), Albania and the Philippines. Particular emphasis has been placed on the development of a quantification for Ni-poor and Ni-rich goethite.

Jan 1, 2008

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By A H. Hofstra, G P. Landis, P Emsbo, A G. Hunt

Models of the evolution of the hydrothermal systems that form porphyry Cu (Mo-Au) deposits are compromised because aqueous magma-derived fluids in the ore zones of most deposits have changed from their original magmatic compositions as a result of cooling, depressurising, mineral precipitation, brine-vapour unmixing and fluid-rock reactions. However, in deep quartz-rich, sulfide-poor veins from numerous porphyry type deposits, we have identified parental fluids trapped in inclusions at near magmatic temperatures and pressures above the brine-vapour unmixing solvus. We have analysed these inclusions for bulk salinity, density, solute chemistry, helium isotopic ratios and elemental composition. These parental inclusions contain 35 - 70 volume per cent bubble, are low to moderate salinity, contain up to ten mol per cent CO2, and commonly contain a chalcopyrite daughter crystal. Our results indicate that these Cu-rich fluids transport Cu from a plutonic complex below upward into a hydrothermal system, where decompression, cooling, unmixing and water-rock reaction drive ore-mineral precipitation. Na/Cl ratios greater than one indicate that in addition to chlorine, sulfur and/or carbonate must play a key role in Cu transportation. Helium isotope ratios indicate that between ~15 and 100 per cent of helium in these fluids is mantle-derived. We suggest that in addition to He, volatiles from mafic magmas in the mantle are also likely to supply CO2, Cu and S to the fluids that form porphyry copper deposits. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970&apos;s to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008