Search Documents

By A Olshina, C Willman, D Moore

GeoScience Victoria has completed quantitative assessments of undiscovered gold endowment in the northern parts of the Bendigo and Stawell Zones. The under cover area in the Bendigo Zone (10 000 km2) is likely to contain approximately 1000 t and at least 290 t of gold in undiscovered mesozonal orogenic gold deposits. For the under cover area in the Stawell Zone (30 000 km2), the estimates are approximately 1200 t and at least 200 t of undiscovered mesozonal orogenic gold. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

By I Chan

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for 14 km linking the Mt Thorley rail loop and running north-west alongside Jerrys Plain Road to the Wambo Coal Mine at Warkworth. A portion of the project is a 260 m long tunnel located where the rail line passes under Jerrys Plain Road. The tunnel has a low cover and is mostly within highly weathered to fresh laminated siltstone interbedded with coal seams, sandstone and conglomerate. This paper presents the design basis and construction methods used to achieve the 100 year design life of the tunnel required by Wambo Coal while also satisfying settlement and vibration limits imposed on Jerrys Plain Road. 

Jan 1, 2008

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

By Hanlu Xie, Liang Yu, Ping Wang, Yuanchi Dong

"The leaching process is the first step when recycling BF slag as raw material for some other products. While studying the kinetics of the BF slag leaching process, a fractal phenomenon was found, which indicated some interesting mechanism in the process. The result suggested a new understanding of the leaching process in detail which useful for the industrial applicationIntroductionTypical composition (wt. %) of blast furnace slag varied in a pretty wide range: SiO2 30–40, Al2O3 10–20, CaO 30–40, MgO 5–10.The ground granulated slag is commonly used as base of roadway (mixed with natural inert for paving, soil stabilization, etc.) or one of the resources of Portland cements because of its good hydraulic activity [1]. To recycle the slag economically, the selective recovery of some components of the slag may be considered. As main components exist in the slag, silica [2, 3 and 4] and alumina [4] recovery was first considered.While recovering of silica from the slag, silica gels are recovered selectively from the leaching solution deriving from the treatment of the slag with waste sulfuric acid. After separation of the exhausted solid of leaching, the silica gel is precipitated from the solution at pH 3.2. Although the silica gels obtained by this procedure contain many impurities and need some more work afterward, it is the first and important step for the process.In the prior work [5], silica extraction using blast furnace slag had been investigated, focused on the pH value of selectively silica extraction. In the present work, kinetics of the leaching process was focused. It is important to design an economical process.ExperimentalThe composition of the slag and the calcined gels has been determined by a LINK860 (Oxford Instruments, Oak Ridge, TN) energy dispersive spectrometer (EDS) in conjunction with a CAMBRIDGE S250-M2 (Cambridge Instrument Ltd., Cambridge, U.K.) scanning electron microscope(SEM). The leaching of slag and the precipitation of silica gels have been conducted at atmospheric pressure in a stirred reactor placed at temperature controlled by a heated water bath."

Jan 1, 2008

By Timothy Barton

The uniaxial compressive strength (UCS) is the most fundamental measurement used in geotechnical rock characterization for mine design. While there are standardized procedures for how to conduct UCS tests, there are no firm guidelines as to when to conduct them. However, it is well known that the strengths of at least some rocks can change during the time between when the core first comes up out of the hole and when it is prepared and tested in the lab. The goal of this NIOSH (National Institute for Occupational Safety and Health) study was to evaluate UCS changes occurring in a broad range of weak coal measure rocks over a one-year time span. The study found the highest moisture contents were measured when the core was fresh, immediately after it was taken from the hole. The specimens then dried rapidly over the next few weeks. Subsequently, sample moisture contents decreased slightly in the winter and increased in the summer in response to the ambient changes in humidity. The measured UCS of the core also changed during the year, apparently in response to changes in the moisture content. The UCS values from the dry, winter months were, on average, 60% higher than the values obtained when the core was fresh, and the summer UCS was approximately 11% lower than the winter UCS. These findings have implications for the use of UCS as an input parameter for both empirical and numerical mine design methods. UCS values of unprotected core tested weeks to months after drilling can be significantly stronger and indicate stronger roof sequences than warranted. In order to obtain the most representative and reliable UCS value, it is necessary to test the core, or wrap and seal it, at the drill site shortly after recovery.

Jan 1, 2008

Epithermal deposits have been defined as the lower temperature end of a spectrum of hydrothermal mineral deposits and are inferred to have formed near the EarthÆs surface. The preservation of an epithermal gold deposit in an Archaean craton is rather problematic, especially when such deposits form clusters or groups as reported for the Pilbara and Yilgarn cratons. For two of the better studied examples of epithermal gold deposits in these cratons, Becher and Wiluna, the evidence that they formed near the Earth surface is non-diagnostic, and the epithermal origin appears uncertain. Despite the simplicity of the original definition, there have been numerous errors in classifying epithermal gold deposits. It is suggested that these errors are primarily due to poor criteria defining the group as there is limited evidence of poor observational science being the cause. The criteria being used to recognise epithermal gold deposits include tectonic setting, ore element suite and quartz vein textures. None of these are diagnostic of epithermal deposits and their link back to the original low pressure-temperature definition of the class is tenuous. There has been definition creep over time as new observations on potential epithermal gold deposits become accommodated within a flexible definition. There is some urgency establishing and then using criteria to reliably identify epithermal deposits. Distinction of epithermal gold from weathered gold deposits is an important step. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

In this presentation, CiDRA?s patented technology platform and its applications will be described. CiDRA's non-invasive, passive sonar array-based flow meter technology provides the volumetric flow rate of single or multiphase fluids by measuring the speed at which naturally occurring structures such as turbulent eddies or density variations convect with the flow past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. This technology has resulted in a unique ability to measure the flow rate of most fluids ? clean liquids, high solids content slurries, pastes, and liquids and slurries with entrained air. Unique and difficult minerals processing flow measurement problems and their solutions will be described. Examples of these problems include flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and lines exhibiting scale buildup. Recent technology developments will be covered.

Jan 1, 2008

By Allan King

Ammonium Nitrate (AN) is most commonly encountered as either a prilled solid or a highly concentrated aqueous solution, with or without organic ( e.g amine) nitrates. Under certain conditions of fire exposure involving prilled or solid AN, the molten state can be formed. The shock sensitivity of the molten material at temperatures greater than 220 Celsius has been found to be much higher than that of the prilled or solid form. Molten AN can be a precursor to events leading up to explosion of a bulk prill storage pile as a result of fire exposure. The explosion hazards presented by molten AN are a function of two factors; 1) its shock sensitivity and the deflagration to detonation ( DDT ) properties of the molten material, and: 2) the ability of large masses of unfueled prilled AN to be initiated and detonate. This paper presents the results of tests designed to determine the shock initiation and DDT properties of the solid ( prilled ) and molten AN.

Jan 1, 2008

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

Qualitative measurement of respirable dust in metal mines is limited and an example of this is demonstrated at Northparkes Mine, where operational experience was sought for measuring dust standards and identifying exposure limits. However, relying on operational experience has limited value due to variation in observations from person to person and is based on visible dust (which is larger in size than respirable dust). However, with sophisticated dust measuring equipment, like the real-time aerosol monitor, dust concentrations can be accurately measured and recorded concisely. Research conducted as part of a collaborative agreement on behalf of Northparkes to launch an occupational dust monitoring program was implemented on the mine site. To form the basis of this research, it was hypothesised that no proper dust measuring testing at the mine site had been adequately identified. In addition, existing occupational hygiene monitoring programs did not adequately quantify employee exposures to these hazards. This project will outline the results of an occupational dust monitoring program, hence greatly improving the capacity to quantify the health risks posed to employees.

Jan 1, 2008

By George Harrison

A great many labor leaders and others advocate shot-firers as the acme of relief for all the dangers connected with solid shooting, and where large quantities of powder are used in one blast in coal mines. Legislative bodies in several mining States have enacted laws providing for shot-firers in mines under such circumstances, the blasting to be done at night after the miners have left the mine. With all due respect to the opinions and honesty of purpose of these advocates of shot-firers, it is evident that a great many of them are not considering this important question in the broad sense it deserves and should be considered.

Jan 1, 2008

By E L. Kotova

Completeness of extraction of a mineral from ore depends on many reasons. First of all it is a function of quality of disintegration of ore. It is supposed that two basic factors: character of structure and texture of the ore aggregate and a disintegration technique influence the quality of the mineral aggregate destruction, æopeningÆ of its internal boundaries. In this paper, the problem of technological mineralogy from the point of view of genesis of the mineral aggregate, its typomorphical features and methods of their quantitative description are discussed. The purpose of this research is to provide information for technologists. It should enable the development of a rational flexible scheme of disintegration of ore with full extraction of a useful component, without its losses and without unnecessary expenses of energy. For achievement of this purpose the mineralogical information should have ½number and a measure+. By the authors, the technique of the quantitative analysis of fabric of the mineral aggregate based on several models û thermodynamic, crystallographic and geometrical is offered and discussed. The leading role in the quantitative analysis of a fabric of ore belongs to internal bounders. But internal bounders of the mineral aggregate by bounders or faces of the mineral individuals or mineral grains are formed. Their geometry, orientation concerning own (mineral grain) crystallographic lattices, orientation and distribution in space of the ore aggregate are proportional to the energy accumulated at origin and the further growth. These characteristics of mineral individuals are consequences of conditions of their formation. That is why the named triad of models is used. From crystallography it is known that faces of different stability and mobility form borders of crystals. They also contain different quantity of energy. Mineral grains also are faceted by different energy borders. They form intergrowths with each other according to a principle of balance or unbalance. That is why in addition to traditional parameters of the description of a fabric of the mineral aggregate (mode and grainmetrical composition) it is necessary to add new. For example, length and the square of intergrowthing bounders of mineral individuals differentiated (in couples), crystallographic symbols of borders, their roughness and so forth. Consequently, solving a problem of the geometrical characteristic of borders, we define also its power characteristic. In this paper experience of application of our technology in studying ores of one of deposits of Urals Mountains is presented. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices, which are carrying out the analysis in a semi-automatic mode, are possessed. Structure and texture of rock or ore aggregate reflect its formation and transformation conditions. It is important to understand that disintegration energy cannot be more than aggregation energy, the energy of intergrowths formation. The square and orientation of mineral individuals borders vary at pressures or stresses of mineral aggregate evolution. These phenomena often cause selective increase in the square of borders at constant average grain size, ie the granulation. Granulation presents the increase in quantity of mineral individuals while their modal share remains constant. At the same time their average mineral grains size. Some mineral individuals increase in size at increased pressure. When lithostatic or lateral pressure drops the majority of mineral grains increases in volume at the cost of intersticial or film solutions or fine grains. These are only special examples of the ontogenesis of the mineral aggregate. They illustrate our statement that all changes in fabric of the mineral aggregate are a reaction on varying external (ie geological) conditions. It is possible to consider that structurisation of totality of mineral individuals as a whole is a process of adaptation of the mineral aggregate, which forms and exists in varying force and energy fields. Differential and integrated geometry of total internal boundaries of the mineral aggregate serves as adaptation mechanism of the mineral grains system. Boundaries form intergrowths of the mineral aggregate. Thus, it is possible to consider that the most informative parameters of the stereometric analysis for restoration of the ontogenesis of the mineral aggregate are the following. First of all, it is a quantitative estimation of the volumetric shape of the ore mineral in crystallographic coordinates, a total area of borders of all mineral grains in the aggregate, the specific square of their boundaries, the specific square of intergrowth boundaries of the ore mineral separately with grains of each minerals of the matrix of the mineral aggregate as well as traditional grainsmetric and modal composition. For realisation of these types of the analysis technologies of measurement, the program of calculation and the devices that are carrying out the analysis in a semi-automatic mode are possessed.

Jan 1, 2008

[ ]

Jan 1, 2008

By Y Bissiri

The ever increasing demand for metals and minerals is putting significant pressure on current mining companies to find more ore. As these companies explore and mine, the future appears to be to go deeper and deeper underground. With depth, however, comes ever increasing costs as infrastructure such as hoisting, ventilation, the movement of workers and materials increase in size and scope. Further, the actual rock mass becomes prone to destruction through rock bursts and the heat generated becomes a major issue resulting in extreme expenditures in cooling plants and some of the biggest air movers in the world. All these issues result in dramatic changes in both capital and operating costs, subsequently making cut-off grades rise. As this trend continues there is an economic limit to how deep one can go, resulting therefore in a severe shortage of accessible ore deposits to mine. This paper discusses the need for larger marine robotics technology and presents the state-of-the-art in current research in underwater tele-autonomy, specifically the development of high bandwidth optical communication networks critical to any future activities (mining, construction, etc) underwater. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008