Search Documents

By David Newman

In Eastern Kentucky, the Darby seam has had an extensive history of coal bumps and pillar bursts. The combination of high overburden, strong rock and coal, subjacent and superjacent mines, and retreat mining has produced incidences of violent pillar failure. The influence of these factors on pillar stability and the potential to bump is illustrated in two case histories. In the first case history, a bump occurred unexpectedly during the retreat mining of a five heading continuous haulage panel. Alternative cut sequences and pillar dimensions were analyzed to identify a geometry that would reduce the potential for future coal bumps or bounces during retreat mining. The viability of the alternatives was constrained by the reach of the continuous haulage system, the overburden depth, and the presence of thick sandstones in the main roof. Each alternative was numerically modeled cut-by-cut to examine the mechanism of stress transfer, as a pillar row is retreat mined. This approach highlighted which cuts were being made in highly stressed portions of a pillar and therefore more prone to coal outbursts. Validation of the numerical modeling was accomplished by comparing the cuts where bumps and outbursts had occurred underground to the highly stressed cuts shown within the models. Recommendations of the barrier pillar width between adjacent panels, pillar dimensions, and changes in the retreat mining sequence were proposed based upon the overburden thickness, geology, and the result of the numerical modeling. The second case history documents a nine-entry panel 3,600-feet long that was retreat mined a distance of 2,064-feet without a significant roof fall or roof-floor convergence. Mine management became concerned about the potential for a coal bump or a large roof collapse within the gob and the resulting air blast. The stress on the pillar line and within the remnant pillars in the gob was quantified through numerical modeling. Changes in mining practices on the current panel were implemented to avoid a bump in the active panel. A barrier was established between the current and the future panels to protect the future panel against abutment pressures from the void area. A change in pillar centers was proposed in the adjacent panel to absorb the side abutment pressure from the gob of the active panel.

Jan 1, 2008

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five underground coal mines in MSHA District 2 (Pennsylvania) and three underground coal mines in MSHA District 11 (Alabama). While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (percent IC) determined by the CDEM agreed well with those obtained later by low-temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By Jessica Egan, Daniel Hodouin, Mohammed Reza Khalezi, Steve Bellec, Claude Bazin, Carl Duchesne

"A model for gold leaching was developed and implemented into a simulator. The simulator uses a description of the ore that is based on the mineral composition and precious metal content. The model accounts for the distribution of minerals and precious metals through the size intervals. An ore texture model based on precious metals and minerals grain sizes within the ore is used to predict the exposed surface of the species in the various size intervals. A model is proposed to predict the rate of dissolution of any species dissolution using the exposed surface, particle size, cyanide and oxygen concentrations, temperature, pH and agitation. The flow of slurry through a leaching tank is modelled using a parallel arrangement of perfect mixers to simulate a bypass and a Cholette-Cloutier mixer model. The simulator can be used for circuit optimization but was developed to provide an environment for learning the basic concepts of process analysis methods. Examples are given to illustrate the application of the simulator for planning tracer tests and sampling campaigns.INTRODUCTIONThe constant pressure to improve the operation of processes that are already close to optimum imposes to plant engineers to be aware of the available process analysis tools and to be able to use them to assess process operation and make a diagnosis to possible problems. Some of these tools are:•,Sampling the streams of a process;•,Data reconciliation;•,Analysis of mixing in reactors;•,Estimation of rate parameters;•,Optimal tuning and flow sheet modification;•,Automatic control and real time optimization.Although some of these tools are part of the curriculum of many university engineering programs, the students are not exposed to actual process analysis problems. In addition the complexity of the ore dressing processes compounded with unavoidable measurement errors and plant disturbances can discourage many motivated engineers. These factors often lead to an incomplete valorization of the collected data and a poor return on the investment associated with the sampling, testing and analysis of the samples.Simulators are readily available for process optimization (Yalcin and Shang, 2006) by allowing:•,The simulation of various flow sheet configurations;•,The simulation of a change of operating conditions;•,The simulation of various control strategies;•,The training of plant operators.However few simulators have been developed with the objective of providing an environment for training plant engineers and technicians to the use of tools for process analysis and optimisation."

Jan 1, 2008

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on cab air filtration system performance. Factors experimentally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab protection performance. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By Kunihiko Takahashi, Gjergj Dodbiba, Hisayoshi Umeda, Toyohisa Fujita

"An increasing number of mobile phones is increasing the number of the discarded mobile phones. Many efforts are thus being made to collect and recycle these devices. This paper is a short introduction of the recycling system of precious metals from the discarded mobile phone, currently available in Japan. Moreover, an attempt has been made to compare the energy recovery and the mechanical recycling of plastic wastes from the discarded mobile phone. The assessment has been carried out in the context of the life cycle assessment methodology (LCA). The environmental impact of each option was assessed by calculating the following impact indicators: depletion of abiotic resources (ADP), and global warming potential (GWP). 1. Introduction In 2003, the demand for mobile phones was increased since the camera was included in a mobile phone and the 3rd generation of mobile phones was introduced. In turn, the number of discarded mobile phone is rising sharply. Generally speaking, all the metallic parts of mobile phones can be recovered and recycled by using smelting and purification techniques. The recycled materials are then used to fabricate other new products."

Jan 1, 2008

By Liang Yu, Yuhua Li, Yuanchi Dong

"High alumina slag, with alumina normally more than 15 pct, is encountered with blast furnaces in China because of high alumina/silica ratio in iron ore as well as sinter and high ash content in coke for cost reason. High alumina slag with high viscosity and high liquidus temperature would lead to higher slag volume and thereby, furnace productivity. In the present work, liquidus temperature of high alumina slag, based on Meishan factory, Baosteel China, were investigated. A liquidus temperature model was introduced in the present work based on basic physical chemistry theory and focused on the chemical composition area used in Meishan factory(pct): Al2O3 from 14 to 17.5 and MgO from 8 to 12, so that the blast furnace slag could be designed for optimum blast furnace performance.IntroductionBlast furnace slag composition[1] has very important bearing on its physicochemical characteristics which affects smoothness of operation, slag handling, coke consumption, the degree of desulphurization, hot metal productivity and its quality etc. The slag properties which affect most are liquidus temperature, viscosity, sulphide capacity and alkali capacity. Variation of these slag characteristics with composition and temperature has been a field of active researches as these its great influence on the blast furnace operation. In the early years, most of these studies were carried out over low alumina blast furnace slags with alumina normally less than 15 pct. High alumina slag was first introduced in India because of its high alumina/silica ratio iron ore as well as sinter and high ash content in coke[2]. And then this problem becomes common as higher alumina/silica ratio iron ore imported and used [2-5]. The most important problem caused by high alumina content is liquidus temperature and then viscosity of the slag.Generally speaking those reported works [2-5] investigated a pretty wide range of chemical compositions and then obtained complex model, respectively. In fact, every factory has its own interest because of different resources. For example, the Al2O3 content from 20% to 30% pct was studied in Tata Steel India [2], but it is too high for Baosteel Meishan. A very lower percentage of alumina content, 14-18 % pct, was mainly used."

Jan 1, 2008

Prepare ATF Report of Theft or Loss (ATF Form 5400.5). A Report of Theft or Loss - Explosives Materials must be prepared when it is discovered that explosive materials are missing from inventory. Submit the original to the U.S. Bomb Data Center and keep a copy for your records. The form can be obtained from the ATF Distribution Center or from www.atf.gov. Although the U.S. Bomb Data Center should be notified as soon as possible, Federal law requires notification within 24 hours of the discovery. A full inventory check is also highly recommended (but not required) to locate missing explosives and to prevent future losses.

Jan 1, 2008

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By Tomoya Nihei, Hiroshi Hayashi

"A novel selenium removal process called Recycled Green rust/Ferrite Process is developed by MMC. In this process, a mixed Fe2+-Fe3+ hydroxide compound, green rust (GR), reduces selenate to elemental selenium, while GR is consequently oxidized to magnetite Fe3O4. Sequencing batch-mode experiment showed that the residual selenium concentration gradually decreased with the number of batch test increased. Stable selenium removal was achieved when the number of batch test exceed 15 times. Optimum selenium removal ratio reached 99.95% where initial Se concentration 2.1mg/L decreased to 0.001mg/L. Furthermore, the continuous feeding test carried out through a pilot-scale plant with a feeding capacity 600 L/hr. Approximately 860-hour-feeding test was carried out for the selenium-contaminated groundwater which had an averaged selenium concentration of 0.88 mg/L. Selenium concentration in the effluent from thickener maintained less than 0.01 mg/L (selenium removal rate of 99%) until a net operating time reached 800 hours.IntroductionJapan is one of the largest producers of selenium, and thus there are potential environmental impacts of selenium on soil and aquatic environments. The Mitsubishi Material Corporation (MMC) owns some real estate properties whose soil and groundwater was polluted by selenium and other heavy metals. These sites include former industrial plants: a smelter for nonferrous metal and a fabricating semiconductors and pigments. Selenium in aquatic environment commonly exists in four oxidation states, namely, VI, IV, 0 and -II. Selenate ion (SeO4 2-), the most oxidized form of selenium, and selenite ion (SeO3 2-) are highly soluble and mobile. Elemental selenium (Se0) is insoluble in water and therefore has much lower toxicity. Because selenium is carcinogenic and teratogenic at high concentration, the national effluent standard in Japan is fixed at 0.1 mg/L and the environmental standard at 0.01 mg/L. Although there are several selenium removal techniques, the most conventional process is coprecipitation with a ferric hydroxide because of its simplicity and low cost. It is known that selenite is adsorbed strongly on the surface of ferric hydroxide, but selenate is not. The low affinity of selenate on oxide mineral surfaces was demonstrated by the fact that selenate could be easily displaced by adding competing anions, particularly sulfate ion. Selenate removal from polluted water is one of the most difficult techniques, and more effective methods are desired. MMC developed a novel selenium removal process [1]. In this process, the concentrated slurry that contains Fe(II)-Fe(III) hydroxyl-salts known as Green Rusts (GRs) contributes to selenate removal. The main components of the iron precipitate in the reactor are GRs and their oxidation product, magnetite (Fe3O4)."

Jan 1, 2008

By John J. Sammarco

Illumination plays a critical role in an underground miner?s safety because miners depend most heavily on visual cues to recognize hazards. Mobile mining machinery, located in the miner?s peripheral field-of-view (±10° to about ±60° off-axis), may pose potential pinning and striking hazards. The main objective of this research was to determine if there were peripheral visual performance improvements for the detection of moving objects when using cool-white light-emitting diode (LED) cap lamps as compared to incandescent (INC) light bulbs commonly used in miner cap lamps. The cap lamp variable of interest is the spectral power distribution (SPD); the illuminances were normalized by a diffusion filter. The second objective was to determine if age is a factor for peripheral visual performance. This is important because the workforce is aging ? the average miner age is about 43 years old. Thirty subjects participated in the study; ten subjects each in the age groups of younger (18 to 25 years), middle (40 to 50 years), and older (50+ years). Visual performance was quantified by the subjects? speed and accuracy of response to detect the rotation of high-contrast (white) circular targets located 3.83 meters (m) away at -20°, 40°, and 50° off-axis. The speed of detection and the number of missed target rotations (accuracy) were measured. The prototype LED cap lamp results were best with a 11% to 15% improvement compared to the INC and LED cap lamps respectively. Age does appear to be a significant factor. For the middle and older age groups?, target movement detection time increased 75% and 60% and the number of missed targets increased 500% and 450% respectively in comparison to the youngest age group. The results also suggest that target location is a significant factor. The subjects? target movement detection time for the 40° and 50° target movements increased 16% and 69% respectively as compared to the -20° target.

Jan 1, 2008

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

The emerging discipline of ægeometallurgyÆ is not new but is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing commercial and cultural trend towards more effective mine site integration and optimisation. The AMIRA International P843 æGeMIIIÆ project (Geometallurgical Mapping and Mine Modelling) is a major new cross discipline research collaboration designed to provide support for this emerging industry trend. The project is currently supported by 18 global mineral companies and involves collaboration between the CODES Centre of Excellence (University of Tasmania), JKMRC and BRC (University of Queensland) and CSIRO Exploration and Mining. These groups represent recognised research excellence in the fields of economic geology, automated core logging, advanced microscopy and process mineralogy, mineral processing, mine planning and resource optimisation. The needs and challenges of geometallurgy as an integrated activity will be outlined together with the ongoing contribution and aims of the AMIRA P843 æGeMIIIÆ project. The main emphasis is on development of predictive geometallurgical indices for key processing performance parameters that reflect inherent geological variability. The ultimate aim is to provide predictive indices of geometallurgical performance that can be confidently embedded into resource models and used for risk-defined mine planning and optimisation.

Jan 1, 2008

global mining boom and in-creased demand for iron ore has lead to a resurgence in the mining industry in Minnesota. At the combined 81st Annual Minnesota Section of SME Meeting and 69th Annual University of Minnesota Mining Symposium, April 15-16 in Duluth, MN, this resurgence was the hot topic as new mining projects were featured in the keynote session. The meeting attracted more than 400 mining industry professionals, including engineers, executives, mining managers and suppliers from around the world. This year?s theme was ?New Ventures in Mining.? The meeting included concurrent technical papers sessions, a keynote session that featured three distinguished speakers and a panel discussion that provided updates on new mining developments in the state. The Minnesota Section of SME technical papers were presented in concurrent sessions, one on mining and one on mineral processing. The mining session included papers on drilling, ore blending, slope stabilization, dust control and operations management. The mineral processing session included papers on plant-control technology, ball mills, pellet strength and fans. Also offered was an SME short course titled ?Simulation based pellet induration optimization.? The Minnesota Section of SME held its annual business meeting during the conference. The 69th Annual University of Minnesota Mining Symposium technical sessions were held on April 15 and also consisted of concurrent sessions on mining and mineral processing. Mining session topics included logistics management, real-time performance measurement, uses for taconite aggregate and environmental issues. The mineral processing session included papers on ore liberation characteristics, zeta potential studies, induration modeling, fuel optimization and conveyor belts. The combined conference included a tradeshow with more than 80 booth spaces featuring vendors offering products and services to Minnesota?s booming mining industry. More than 900 people, including conference registrants and special invited guests of the vendors, at-tended the tradeshow opening reception. This was the largest trade show in many years ? an indication of the vitality of the mining industry in Minnesota.

Jan 1, 2008

By Takashi Sasaoka

The PT. Adaro Coal Mine targeted in this research is located in South Kalimantan, Indonesia. The coal production of this mine is increasing year, with about 35 M tons of coal produced in 2006. This mine faces many ground control problems, especially instability of the footwall. Large-scale landslides occur often in the footwall; this may be because of weak rock and the effect of footwall rock weathering. Hence, prompt measures must be developed and followed in order to preserve the stability of the footwall and make this mine safe. Additionally, the final pit design is now being reconsidered because of the increasing demand for and high price of coal. With these issues in mind, this paper describes a solution for improving the stability of the footwall and discusses the final pit design based on the results of an on-site investigation and numerical analysis.

Jan 1, 2008

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

By Ramasamy Santhanam

"India’s present annual marine fish catch is 2.9 million tonnes and its low value fishes such as sardines, sciaenids, goat fishes and leiognathids amount to 60%. The fish meal obtained from these resources is mainly used presently as an ingredient in live stock and aquaculture feeds. These fishes offer vast scope in the production of pet foods. Pet foods prepared with leiognathid fish meal (60%), maize flour (10%), wheat flour (5%), vitamin and mineral mixture (5%) and water (20%) and experimented with 50 cats and 50 dogs were found to be ideal. Depending on protein level, feeds are being formulated for experimenting with more number of pet animals. Training programmes are also planned for unemployed people to popularize pet foods for commercial purposes.IntroductionIndia’s present annual marine fish catch is 2.9 million tonnes and low-value fishes sucha s sardines (Sardinella albella, s. gibbosa, S. fimbriata and S. melanura); sciaenids (Otolithus spp. and Jhonius dussumieri); engraulids (Stolephorus indicus); and leiognathids Leiognathus bindus, L. equilus and Gazza achlamys) constitute 60% (Figure 1)[1]. The fish meal obtained from these resources is now mainly used as an ingredient in livestock, poultry and aquaculture feeds. Considering the rich nutritional status of these low-value fishes, it is felt that these resources could be converted into value-added products viz. pet foods."

Jan 1, 2008

By N. Geoffroy, E. Benguerel, G. P. Demopoulos

In the late 1990s, a chemical process to remove mercury and selenium from weak sulphuric acid solutions was patented and implemented in the CEZinc refinery in Valleyfield, Quebec. The CEZinc process comprises two stages. In the first one, sodium sulphide is added to the weak acid solution in order to precipitate the soluble mercury. The solution is then treated with sodium dithionite in order to reduce the selenium to elemental form. Because of recent changes in the composition of the industrial solution, a project to study the background chemical reactions was started. In this paper, a review of the background chemistry is presented on the basis of several eh-pH diagrams on one hand, while on the other experimental results are reported dealing with the reaction of selenium (IV) species with either dithionite, sulphide or a combination of the two. According to this work, elemental selenium enjoys a wide pH-eh range stability with selenium sulphide being metastable. Selenium (IV) in single metal synthetic solutions was found to be reduced - to elemental state - at ambient temperature down to ppb range with dithionite as long as the stoichiometric ratio (dithionite/selenium) was in excess of two and the pH < 1.7. Under these conditions the reaction was very fast reaching completion within one minute. Sodium sulphide proved equally effective in reducing selenium (this time as selenium sulphide) to ppb range from single metal solutions. However, in mixed Se-Hg solutions deviations from this "ideal" behaviour was observed resulting in higher levels of residual soluble selenium left in solution.

Jan 1, 2008