Search Documents

By Andrzej Luszczkiewicz, Magdalena Duchnowska, Jan Drzymala

A selected flotation system of beneficiation of the copper ore at KGHM Polska Miedz S.A. has been analyzed in the article. It was found that a proper assessment of upgrading must be based on two elements, that is the upgrading process selectivity and working point of the considered flotation unit, both determined, preferentially by means of the Fuerstenau recovery-recovery upgrading curve. The Cu recovery - non-Cu components recovery upgrading curve was selected for calculations because its background lines (no separation and ideal separation) are insensitive to changes in the grade of feed of the processed material. This approach allows a comparison of upgrading results for feeds having different grade, being upgraded in various flotation machines and under different physicochemical conditions. It was shown in the paper that the main criterion for comparison of two working in parallel systems is selectivity of upgrading. However, when two flotation machines, despite of the same selectivity, produce concentrate and tailing of different grades, it is necessary to analyze their working points using upgrading curves. The proper position of the working point depends on the criterion imposed on the process and is a result of not only basic parameters of the upgrading process such as feed, concentrate and tailing grades but also on economic parameters such as costs associated with the production of concentrates and the time needed for their production.

Jan 1, 2014

By Chi M. Phan, Anh V. Nguyen, Geoffrey M. Evans, Graeme J. Jameson

Surfactants are used to control the interfacial properties of the gas-liquid and liquid-solid inter- faces inflotation. This paper investigates the dynamic adsorption of surfactants at the gas-liquid intelface. The dynamic adsorption process was modeled by considering the surfactant mass transfer to the gas-liquid interface by dimion and the Langmuir and Frumkin adsorption isotherms. The numerical computation was applied to solve the non-linear governing equations. The dynamic adsorption was measured in tenns of the dynamic surface tension using the pen- dant drop method. The theoretical modek were compared against the experimental data obtained with non-ionic (Dowfroth 250) and ionic (sodium dodecylbenzene sulfate, SDBS) surfactants. The theoretical results agreed well with the erperimental data for SDBS, but not for Dowfrother 250, especially for the initial stage. Reasons for the variation in results are given in the paper.

Jan 1, 2005

By G. Brooks, J. T. Ellington, M. Yensco, G. E. Mcquien, M. T. Ityokumbul

Coarse silica flotation from intermediate pebble (IP) product has been carried out a pilot plant Dual Extraction Column (DEC) at an operational phosphate mine in Central Florida. The solids feed rate ranged from 4.16 – 5.3 TPH while the amine dosages ranged from 0.32 – 0.93 lb/T. The optimum amine dosage when using recycled process water was deter-mined to be 0.6 lb/T. With a feed containing 40-45 BPL and 38-45% insol, the results show that the IP can be upgraded to 56-61 BPL and insol of 16-22% at 85-90% BPL recovery. The results show that the DEC is an effective device for flotation of coarse silica from the IP. The advantages of upgrading the IP prior blending with the pebble are presented and discussed.

Jan 1, 2004

By V. R. Degner

Comments Summary It is very interesting to review the technical changes which have occurred in the industrial practice of minerals flotation over the past two decades. In 1972, worldwide industrial flotation was dominated by 'mechanical' flotation machines having an individual cell volume less than 500 cu.ft. Manufactures, such as DENVER Eqpt. Co., OUTOKUMPU, WEMCO, GALIGHER (AGITAIR), AKKER, and later DORR-OLIVER, produced flotation machines featuring a mechanical rotating impeller which served to mix pulp and air, prior to flotation, and to keep the solid ore particles in suspension. While sharing this common mechanical impeller feature, the machine design of the various manufactures differed in detail; particularly in regard to the vertical location of the impeller in the cell and the means by which flotation air was brought into contact with the pulp within the rotor mechanism. A review of the existing technical literature in 1972 would identify academic research studies, particularly at Columbia University (N. Arbiter, C, Harris ...) aimed at comparing flotation cell design concepts, of the various machine manufactures, on a hydrodynamic basis. These research studies were confined to very small, laboratory bench size, flotation machines, and the benefits of incorporating hydrodynamic considerations in the scale-up of the existing 300 cu.ft. mechanical flotation technology to larger cells was not commonly practiced industrially. Technological advances in minerals flotation, over the past two decades, have been influenced by a variety of economic factors including the increasing development of lower grade ore bodies, the attractions of producing a higher grade final concentrate, and the economy of tails retreatment to improve overall plant recovery performance, and flotation system “optimization" became increasingly important through the 1970-80 time period. The trend toward processing lower grade ores led to higher tonnage mill operations, and stimulated the development of the very large capacity mechanical flotation machine for roughing and scavenging duty. In 1972, the 500 cu.ft. size flotation machine was being pilot tested and introduced to the industrial market. Today, 1993, individual cell volumes of 1500-3000 cu.ft. are operating successfully throughout the world, and well planned plant test programs have concluded that the very large flotation machine can achieve the same metallurgical performance level of its smaller predecessor. The large flotation machine development record clearly credits the incorporation of internal cell hydrodynamic considerations in guiding the scale-up of the mechanical flotation machine to large sizes. This guidance eliminated, or reduced significantly, costly in-plant prototype machine changes which increase Dramatically with increasing flotation machine size. Early in the 1980's, at approximately the time that flotation machines in the 1500 cu.ft. class were being introduced into the market, it became evident that the availability of the very large mechanical flotation machine brought with it the need for a systematic means to "optimize" the flotation system by relating flotation cell size, row length (i.e. number of cells per row), and flotation rougher, scavenger, and cleaner system configuration to the economic objectives of the concentrators' operating management. Flotation system optimization consists of quantifying the flotation process performance using a suitable model which relates the kinetic response of the trace specie and the gangue material to the cell overflow, and produces a numerical relationship between product grade and value recovery. The computer analysis technique has proven to be an invaluable tool in determining the kinetic model coefficients which characterize a given application, and is also used to apply the resulting model to a proposed minerals beneficiation situation seeking to "optimize" the flotation system by relating metallurgical grade-recovery performance, flotation cell size, and circuit arrangement, to plant space, installation, and operating costs. It is interesting to note that these same computer based kinetic flotation analysis techniques can be easily applied to quantitatively evaluate the effect of different chemical reagent strategies, and flotation air transfer, on process performance for a variety of candidate feed ore types.

Jan 1, 1993

By P. R. Pereira

This paper presents a comparison between the simulations of a semi-empirical model and a theoretical model for the prediction of radial stress in rock. The results of the simulations were compared to the results of a field test. The comparison of the radial stress predictions shows that in the semi-empirical model use of the plane wave approximation as the basis for the prediction of the radial stress provides a much better result than the theoretical model. The theoretical model includes the correct elastic wave geometry and theory but fails twice, firstly by considering the charge as a point (unit) energy source therefore; and secondly by using a Delta function with a very sharp rise and decay time to simulate, with no distinction between non-linear and linear zones, the attenuation of the energy per unit volume at the shock wave front as the wave moves away from the borehole. The results of the semi-empirical model were within the same order of magnitude as the results from the field test whereas only one result from the theoretical model came close to the result of the field test. However, even this closer result for the theoretical should be taken with caution as there was no measurement in the field test made at this distance from the borehole. Finally, because of its potential portability, convenience, and cost-effectiveness the theoretical model can be a most valuable tool for mining and civil construction operators in the early design of blasting rounds and of the mining operation itself.

Jan 1, 1993

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Willard P. Ward

It is the object of the present paper to bring to the notice of members of this Institute, the results of experiments made during the past six months in the manufacture of the alloys of iron and manganese in the blast-furnace. The ores at hand and available for the purpose were brown hematites, containing but a very small percentage of manganese, and various manganese ores containing a small percentage of iron. It is hardly necessary here to call attention to the statements regarding the production of iron-manganese alloys from such ores, which are given by all the well-recognized authorities on metallurgy. Suffice it to say, in a few words, that they hold that the operation is practically impossible, and that in the use of oxides of iron and manganese, mechanically intermixed in the same ore, much difficulty has been found in producing spiegeleisen. Spathic ores, containing manganese chemically combined, are alone recommended for the production of spiegel, and even then it is said that well-managed furnaces produce only about 75 to 80 per cent. of spiegel, the balance of the production being white laminated pig or gray iron.

By Wilbur S. Burbank, Robert G. Leudke

The impressive western San Juan Mountains of Colorado were carved by Pleistocene and Recent erosion from a thick blanket of Tertiary volcanic rocks that rests upon a basement of metamorphic, sedimentary, and igneous rocks ranging in age from Precambrian to Tertiary. These rocks record a long, complex, and fairly complete sequence of geologic events that have affected the region through much of geologic time. The geologic history of the region includes several periods of deformation, erosion, and igneous activity; closely associated with two of these periods were two periods of mineralization. The older of these was related to Late Cretaceous-early Tertiary (Laramide) intrusive activity, and its deposits occur in the older sedimentary units. The younger, of later Tertiary age and related to the widespread middle Tertiary extrusive and intrusive activity, is the chief concern of this paper. Tertiary volcanism built a great plateau surrounding the San Juan volcanic depression, a complex of subsided crustal blocks in the vent areas. The Silverton and Lake City cauldrons, nested within the larger depression, were domed by resurgent magma that created keystone grabens along the distended crests of the domed floors and many postcauldron radial and concentric fractures, dikes, and intrusive plutons within and marginal to the cauldron sites. The postvolcanic evolution of large quantities of gases, chiefly carbon dioxide and water, propylitically altered the rocks in and around the volcanic depression prior to the younger period of ore deposition. The ore deposits, localized mainly in the radial and concentric fractures about the cauldrons and in the associated graben faults, include fissure veins, chimneys, replacements, and disseminations in volcanic and underlying basement rocks. Fissure veins, constituting the major economic source, yielded precious- and basemetal ores. Most veins are compound with sphalerite, galena, and chalcopyrite; some veins contain silver-bearing arsenical sulfosalts and free gold. These minerals occur in predominantly quartz gangue. However, gangues composed of several manganese silicates and carbonates and relatively· barren of metals are abundant locally and probably originated by alteration of rocks at roots of faults and fissures during evolution of carbonatic solutions. The bulk of the ores are hypogene and probably had their source in deep parent magmas of the shallow eruptive rocks. Total production since the early 1870's has exceeded half a billion dollars in recovered metals, with a ratio of precious- to base-metal values of about 3 to 2. Since 1930, improvements in metallurgical treatment and mining techniques have increased the base-metal yield.

Jan 1, 1968

By F. E. Armstrong

The Bureau of Mines has conducted a research program to systematize the art of locating uncharted and lost oil and gas wells that penetrate coal seams; this publication presents a preliminary summary of its findings. Although no method or combination of methods will guarantee finding all uncharted and abandoned wells in a particular area, at least 75 percent of such wells can be located by compiling and applying all available information and using modern metal detectors.

Jan 1, 1973

By T. R. Twiddle

The sequential flotation of copper, lead, and zinc in that order is practised at the Broken Hill Concentrator of the Black Mountain Mineral Development Company (Pty) Limited. The minerals of economic importance are chalcopyrite, galena, and sphalerite, with associated silver. The targets for recovery and grade in the lead and zinc circuits were reached quite readily after start-up, but the copper circuit failed to meet the performance requirements with respect to both recovery' and grade. The original circuit for copper is described, together with the subsequent investigations and modifications that were required to produce acceptable metallurgical results. Circuits for semi-bulk and bulk flotation were tried, and the effect of the oxidation state of the pulp was investigated extensively and found to be all important. Tests were conducted on the depression of lead in the cleaning circuit by the use of sodium dichromate, and on heating with the addition of sulphurous acid. The latter technique was ultimately the more successful. The proportion of fresh to recycle water entering the circuit was shown to be important. The original reagent regime was altered and augmented. A more recent problem has been the contamination of the ore with cemented backfill. The changes that this new condition necessitated are described. Success has been measured by a continuous improvement in the economics of the copper recovery.

Jan 1, 1984

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By Michaela Dina Stanescu, Emilia Visileanu, Eftalea Carpus

"The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. An important role in manufacturing textile products it has the notion of eco-design, which has grown considerably over the last twenty years with increasing awareness of environmental and social problems in the industry.Introduction“Humanity must learn from the global financial and economic crisis experience""- is the conclusion of the policy makers who should develop a strategy designed to reinvigorate the economy and make possible an"" intelligent, sustainable and favourable to inclusion” growth, by a better coordination of national and European policies.The new vision for social market economy is based on three priority areas: smart economic growth, the development of an economy based on knowledge and innovation; sustainable economic growth, the promotion of a competitive economy with low carbon emissions and an efficient use of resources, as well as an inclusive economic growth, the promotion of an economy with high degree labour employment, which would generate social cohesion. The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. It is obvious that at the origin of pollution there are the technological processes of textile processing with impact on air, water, soil, as well as the storage processes. In all phases of obtaining a product, a series of secondary products and textile wastes with impact on the environment occur. The product used becomes also a factor of environmental pollution, which in most cases fails to assimilate."

Jan 1, 2012

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By Vicente Gonzáles Otoya

El presente texto describe el descubrimiento, cubicación y evaluación del fosfato de Bu -Craa en la provincia de Sahara. Para ello, se realizó campañas donde se hizo el reconocimiento exhaustivo del límite de afloramiento del Paleoceno en toda la provincia, que va desde Hasi Melehes hasta Villa Cisneros, así como se determinó que las capas fosfatadas importantes estaban localizadas en este tramo geológico. Así también se revela la geografía, sondeos, testificaciones, pozos y calicatas y la organización del trabajo de evaluación de dicho sector.

Sep 1, 1971

By Denholm WT

A mathematical model has been developed for intense pneumatic smelting processes, such as the Sirosmelt group of processes, to assist in establishing optimum process conditions and to permit operator training. The model first solicits input operating conditions from disk files and from the operator. During operation, the feed, fuel, and air (or oxygen) rates are automatically adjusted to maintain the desired process targets. Alternatively, these parameters, as with all other inputs, may be manually controlled by the operator. Selected process parameters are displayed to the terminal in a regularly updated diagram of the process,. Outputs of detailed information including heat and mass balances are available for immediate inspection or for use by ancillary plotting packages. Development of a robust free energy minimization routine has led to a flexible and time efficent model capable of handling a range of pyrometallurical systems. Modelling of tin smelting, lead smelting, copper smelting, matte fuming, and pneumatic steel-making has been sucessfully carried out. Typical outputs from the model are given and discussed in terms of their internal consistency and relationship to the operation of the relevant Sirosmelt process. `

Jan 1, 1984

By Douglas R. Schmitt

In general, knowledge of the state of stress within the Antarctic lithosphere remains largely unconstrained due in part to Antarctica?s inaccessibility and because of the paucity of seismic focal mechanism solutions. As such, an important component of the ANDRILL project was to acquire new information on the stress directions and magnitudes within the upper crust. Extensive fracture mapping of the core and oriented ultrasonic televiewer logging were carried out to provide strong constraints on both stress orientations and the faulting regime. The first hydraulic fracturing stress determinations in Antarctica were also carried out to provide complimentary stress magnitudes. These measurements were accomplished using a wire-line transported hydraulic fracturing system consisting, essentially, of two synthetic polymer packers that were inflated to isolate the 1-m long pressurization interval. The tests were conducted at the end of the drilling and logging in a ~130-m section specially drilled below 1000 mbsf (nearly 1500 m from the rig floor) for hydraulic fractures. This zone was drilled primarily through competent, dense, and low permeability diamicts. The core fracture and televiewer logging information was used to site twenty separate measurements. Classic hydraulic fracturing pressurization records with unambiguous breakdown and fracture closure pressures were obtained in about half of the measurements. The remaining tests provided fracture propagation and closure pressures that are consistent with the classic breakdown curves, but they did not include a clear breakdown pressure and are indicative of the reopening of either natural or drilling induced fractures in the wellbore wall. The preliminary analysis of the results are in generally good agreement with the stress directions indicated by the core fracture logging and the stress regime suggested by the character of the drilling induced core fractures.

Jun 1, 2012