Search Documents

By Dr. Rory Cameron, Dr. Terry Cheng, Dr. Nadia Mykytczuk, Ian Bedard, Kristie Tarr, Ruth Joseph

Pyrrhotite-rich tailings from Sudbury, Ontario mining activities are known to contain significant amounts of EV metals, such as nickel and cobalt.  CanmetMINING has developed a novel bioleaching process for recovering the nickel and cobalt (both critical for vehicle electrification) from tailings that incorporates partial neutralization and iron removal in the bioleaching circuit; bench- and pilot-scale tests have resulted in excellent nickel and cobalt recovery over a range of temperatures.  However, this process generates a new bioleach residue, which is heavier and more voluminous than the original tailings due to pyrrhotite oxidation and jarosite formation during the bioleaching process. This residue can be problematic for long-term disposal. A possible solution being studied for this issue is using mine backfill as a disposal mechanism.  Underground backfilling allows for effective re-purposing of mine waste, however the backfill must also be able to withstand a certain load, since in most cases it is used as an underground construction material, such as in cut-and-fill mining methods.  Therefore, the composition of the mill tailings must be such that when combined with a binding agent and pumped underground, the slurry or paste is then able to withstand a certain load within a certain period of time.  Unfortunately, high-pyrrhotite content tailings, commonly found on mine sites in Ontario and Quebec, are reactive and can easily oxidize and produce acidity and/or metal-laden drainage under some disposal conditions. This means that the pyrrhotite in the tailings can lead to acid mine drainage if stored on surface, however, it can also cause strength degradation if re-purposed in too high a concentration in underground mine backfill.  The research being done at CanmetMINING related to the bioleaching process is aimed not only at recovering nickel and cobalt from mine tailings, it is also being used in an attempt to neutralize the tailings to reduce acid mine drainage and backfill strength degradation. This paper reports on research designed to evaluate different options for transforming the bioleaching process residue into iron oxide phases, for better environmental footprints if stored on surface, as well as increased disposal possible, if re-purposed as underground mine backfill material.  

May 4, 2025

By M. C. van Eeden, R. Vermeulen, K. B. Le Bron

This paper presents the lessons learnt during the transition from an open pit method to a sub-level open stoping method at the Koidu Limited kimberlite pipe. These learnings may assist other mines with planning, both from a practical implementation perspective (layout, charging up challenges), and a method for estimating potential dilution and stability challenges associated with the interaction between the surface and underground excavations. Predictive geotechnical stability modelling was successfully applied to highlight potential failure zones, which allowed modification and enhancement of the mining layouts and quantification of the potential dilution of the kimberlite from indicative instabilities.

Sep 1, 2025

By E. Kalhan, C. Kincal

One of the biggest problems in open pit mining is slope stability. The avoidance of slope stability problems depends on a comprehensive assessment of environmental and operational factors such as geology, climate, and mining activities. In the light of these considerations, slope geometries should be determined in accordance with engineering principles. In this research, the slope stability of rock slopes in a mine opened in a gneiss geological unit has been studied. Production activities were ceased in 2019 due to the slope movements in the eastern part of the quarry. In order to safely continue the production, field works were primarily carried out. To assess slope stability, detailed discontinuity surveys were carried out on bench faces. Subsequently, kinematic and numerical analyses were employed to identify geometries that are expected to maintain stability under the prevailing geological structures and environmental constraints. Engineering geological studies such as scanline measurements in steps and investigation of potential failure mechanisms by kinematic analysis technique were carried out. Small module reactor and Q-slope rock mass classification systems were used to evaluate slope stability. Based on these classification systems potential unstable rock slopes were identified and thematic maps were created using geographic information systems. The most suitable slope geometries are suggested for these slopes. In addition, the improvement methods suggested by the rock mass classification systems were proposed for these slopes.

Sep 1, 2025

By M. Royle, A. Bloem, R. Uken

Rock mass damage induced by mining increases the fracture frequency and joint aperture width in the pit walls and rock mass behind open pit mine slopes. The depth and intensity of this mechanical damage relative to the pre-mining state is not well understood and yet is a major factor in the development of slope stability models and operational guidelines. The induced damage can be partitioned into domains or zones. The blast damage zone is essentially a ‘free flow’ rock mass volume, which transitions quite rapidly into the excavation damage zone, which extends beyond that. In both zones, transient high in situ water pressures are often linked to unstable slope conditions. Whereas rock damage can enhance passive depressurisation in the rock mass, high infiltration rates on the other hand, as one could expect during rainstorm events, will decrease slope stability within the dilated pit rock mass, especially in the blast damage zone-excavation damage zone, by increasing pore pressures for short periods of time. Ice jacking and freshet are additional factors to consider in (sub) arctic environments and can be exacerbated by unfavorable rock fabric orientation. On a local scale, brittle deformation damage zones, in the form of faults, can contribute to slope instability, or enhanced stability because of slope depressurisation, depending on their location and orientation relative to the pit shape and the water sources. In this study, the shapes of the damage zones and their anticipated impact on infiltration and/or passive depressurisation are considered for different pit morphologies, rock mass conditions, in situ stress, and hydrogeological settings. Some unusual hydrological situations, like mining towards rivers and lakes and the potential effects on pore pressures, are also considered. This investigation has resulted in the development of a method to adjust initial hydraulic conductivity values used to estimate transient pore pressure conditions found in rock masses exposed in different pit morphologies and stress regimes as well as discontinuities’ orientation relative to open faces within the open pit mine. The changes in K values and pore pressures can then be used to determine hydrogeological influence more accurately on future pit slope stability.

Sep 1, 2025

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

By P. Linzer, L. M. Linzer

The gravity method is often applied in mining-related scenarios such as geological and mineral exploration, detecting subsurface cavities and voids (“receptacles”) that may become sinkholes, siting of surface structures, fault-mapping, and more. It is also widely applied in geotechnical engineering to map subsurface karst profiles and to detect subsurface cavities, such as can occur in open pit mines. While it is widely acknowledged that, compared with other available geophysical methods, this method is the most applicable to the karst profiling problem, survey geometries applied in the field are often far from optimal. The gravity surveying specifications prescribed in SANS 1936 omit some key requirements for optimal survey outcomes, and this paper is intended to fill those gaps. The authors have seen scopes of work that require only a few measurements over the footprint of a proposed structure, indicating a lack of understanding of the nature of the gravitational field. A single gravity measurement is subject to the camouflaging effects of several influences, many of which can be larger than the anomaly caused by the subsurface density variation itself. Papers in the body of literature show an awareness of the need to map the regional field so that it can be subtracted to unmask the residual gravity anomaly, but rarely do they examine how instrument sensitivity governs the size of detectable anomalies or discuss how a detailed terrain correction can be instrumental for isolating faint targets. This paper aims to explain how to apply the gravity method correctly to mining and geotechnical problems, specifically in the detection of subsurface cavities. It discusses various factors to assist with optimising the acquisition of gravity data and its processing so as to maximise the practical value of gravity surveys.

Sep 1, 2025

By C. Banff, E. C. F. Hamman, J. Venter

Open pit slope stability analyses for large scale instabilities are often carried out using limit equilibrium, finite element or finite difference computer programs. All of these require empirical estimates of rock mass shear strength when calibrated values are not available, which is a common occurrence. A common method of estimating rock mass shear strength is the Hoek-Brown failure criterion, which often over- or underestimates rock mass shear strength when used in limit equilibrium or elastic linearly plastic slope stability analyses, resulting in published alternative estimates for the coefficients of the Hoek-Brown failure criterion. This paper investigates the differences between limit equilibrium and elastic linearly plastic slope stability analysis based on the Hoek-Brown failure criterion. The investigation consisted of a comparison of 3840 RS2 finite element analysis models completed with strain softening, and 216 Slide2 limit equilibrium models. The models were used to evaluate a methodology to determine equivalent limit equilibrium and elastic linearly plastic shear strength parameters that provide the same stable slope angles and instability back break distances as the more representative strain softening stress analysis methods. This paper presents the methodology and compiles the results into design charts and equations for equivalent limit equilibrium Mohr-Coulomb shear strength parameters, that simplify calibration against actual case studies. The results compare well with older empirical shear strength estimates, however, a detailed calibration of the results against case studies will need to be carried out. The analysis also did not consider pore pressure effects; this is left for future publication.

Sep 1, 2025

By T. Dlokweni, M. Bester, C. Koegelenberg, I. Basson

Certain degrees of safety, economic, and financial risk are implicit in any mining operation. At Thabazimbi Mine, slope stability was one of the major sources of risk, largely due to data uncertainties. Consequently, a risk-based approach in slope design was followed. On 6 June 2015, a slope failure occurred in Thabazimbi Mine’s Kumba pit, involving approximately 65 million tonnes of rock failing into the pit and the valley below. Although the failed mass moved rapidly and resulted in a run-out distance of approximately 900 m, controls had been put in place to successfully evacuate all personnel. Risk assessment during the onset of failure supported the decision to not compromise the safety of personnel in any way, leading to unavoidable equipment loss. This contribution presents the failure as a case study in the context of a risk-based approach to slope design as well as the importance of implementing geotechnical controls to effectively manage slope instability risk. Furthermore, a comprehensive back-analysis was performed, on a fully constrained 3D model, utilising 3DEC software, to gain insights into the failure mechanism. In conclusion, lessons from the Thabazimbi slope failure are valuable as they demonstrate the importance of following a risk-based approach in slope design to effectively manage safety and financial risk in open pit mines.

Sep 1, 2025

By Philani Larrance Ngwenyama, Ronald CW Webber-Youngman

Through-the-Earth (TTE) communication systems were developed to provide post-accident communication in underground mines. Unlike primary tracking systems, they do not require any major infrastructure installations underground. Instead, they use the Earth’s overburden as the medium or channel for the transmission of electromagnetic waves between surface and underground. Under ideal conditions, TTE communication systems should be able to provide full-duplex, two-way voice, text and data communication. However, this will depend on the design and optimization of the different types of TTE communication systems (that is, antenna and electrodes), and understanding of the rock properties and their influence on the transmission of signals. This can help simulate and model the transmission efficiencies and predict the possible range and data rates. Being able to optimize the performances of these systems can enhance rescue missions, improving the chances of saving trapped miners, and ultimately reduce fatality rates across the mining industry.

Feb 1, 2025

By Mir Ahmad Mohammadi

Land uplift due to mine flooding has become a significant challenge with extensive historical mining activities, particularly in Germany’s Ruhr district. The cessation of coal mining operations has led to a gradual rise in groundwater levels, altering geotechnical and hydrological conditions and causing surface uplift. This study develops a system dynamics (SD) model to investigate the dynamic interactions of influential variables such as groundwater levels, total stress, porosity and permeability with land uplift over time. The model integrates causal loop diagrams (CLD) and stock flow diagrams (SFD) to comprehensively understand the system’s behavior. SFD illustrated that for a 10 percent increase in groundwater level, the land uplift increased by about +6 percent, and a rise of 200 percent in total stress caused an 18 percent increase in effective stress, which decreased the land uplift by about 20 percent. This study highlights the importance of dynamic modeling in informing land-use planning and mitigating the long-term impacts of land uplift after mine closures.

Mar 1, 2025

By Alessandro Navarra, Aldo Quelopana

Sophisticated models have progressively been developed to address the challenges related to long-term, openpit mine planning under conditions of geological uncertainty. Prior research has acknowledged that strategies for mine planning and the design of mineral concentrators are interdependent; thus, it is highly desirable to optimize them together. However, achieving detailed holistic optimization of the mineral value chain remains unresolved because of the inherent limitations associated with mathematical formulations and computational processing capacity. This paper details a method that contributes to bridging these limitations by employing a novel parallelized variable neighborhood descent approach combined with an embedded mass–balance component using linear programming techniques refined through Dantzig– Wolfe decomposition. This approach is exemplified through a case study of a gold deposit, which illustrates the enhanced performance capabilities of the new algorithm. The findings demonstrate significant improvements in the optimization process for mine planning, providing a stronger link between the mine’s output and processing plant’s capabilities.

Mar 1, 2025

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024

By Joel Lööw, Johan Larsson, Stig Vinberg, Malin Mattson Molnar, Mats Jakobsson, Jan Johansson

The mining industry is undergoing rapid transformation, driven by technological advancements, sustainability concerns and demographic shifts. This transformation will put more younger people in management positions. This study provides valuable insights into the leadership behaviors of younger and older managers within a large Swedish mining company, highlighting the importance of managerial experience and targeted training programs to foster effective leadership, particularly in the context of change management. The findings emphasize the need to create work environments that support managers to develop their leadership, contributing to improved employee well-being, operational efficiency, and adaptation to the changing demands of the modern mining sector.

May 1, 2025

By Juan L. Yarmuch, Gonzalo Sepulveda

Medium- and short-term mine planning holds immense significance in optimizing production and resource utilization. It serves as a vital link between the long-term strategic plans and the day-to-day operational activities of a mine. In this context, a mathematical formulation is proposed to incorporate mining width constraints into the production scheduling process, aiming to maximize the net present value (NPV) of the schedule while ensuring enough room for the operation of mining equipment.

Jul 1, 2024

By S. Afrouz, C. Keles, E. Sarver, A. Greth

While respirable dust monitoring has long been done on the basis of mass concentration, it is increasingly recognized that specific dust characteristics may play an important role in health outcomes. Scanning electron microscopy with energydispersive X-ray (SEM-EDX) can be used for detailed particle analysis, but the quality of results can be dependent on the sample substrate; ideally, particles should be deposited on a smooth, uniform substrate like polycarbonate (PC). While direct air sampling onto PC filters is possible, this is not the standard approach in many situations. For example, in coal mines, polyvinyl chloride (PVC) filters are often used. They enable conventional mass-based analysis — of the total respirable dust, and the content of crystalline silica in this fraction — but are fibrous and thus not ideal for SEM-EDX or other microscopy. To address this issue, the current work tested a simple method to recover respirable dust particles from PVC filters and redeposit them to PC. Results generally indicated that recovered particles are representative of the original dust sample in terms of mineralogy distributions. Where this was not the case, the issue appeared to be with high particle loading density during SEM-EDX work rather than related to the recovery/redeposition method itself. This bodes well for applications where a single PVC filter sample could be used for nondestructive analysis to determine respirable dust mass and/or respirable silica mass, followed by preparation for SEM-EDX analysis to evaluate particle characteristics. The recovery and redeposition method might also be adapted for other applications, such as to enable the analysis of respirable dust samples collected by the continuous personal dust monitor (CPDM).

Oct 1, 2024

By Mehmet Mesutoglu, Ihsan Ozkan

This study investigates the feasibility of rock bolting support in an underground coal mine gallery with a thick coal seam. The Ömerler underground coal mine working area, owned by West Lignite Enterprise of Turkish Coal Enterprises, was selected for this purpose. Longwall top coal caving is implemented as the production method in the Ömerler underground coal mine. Field and laboratory studies were conducted to determine rock mass and rock material properties, followed by experimental, empirical and numerical analyses based on the acquired data. The obtained design results were evaluated using a resin-grouted rebar rock bolting (RBR) system and steel arch support (SAS) pilot application areas. The numerical modeling results conducted using the fast Lagrangian analysis of the Continua 3D (FLAC 3D v6.0) program indicated less displacement and secondary stress change in the RBR-supported zone compared to the SAS-supported zone. In situ measurements also demonstrated that RBR provided more successful support to the roof during coal production activities. The findings suggest that RBR is a more effective solution when evaluating the feasibility of rock bolting support systems in underground galleries with thick coal seams at the Ömerler Mine. This study emphasizes the importance of more sustainable and safe support systems to enhance operational efficiency in the coal mining industry.

Mar 1, 2025

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By Mary Nelima Ondiaka, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau, Talabi Henry Kayode

Iron ore is essential in steelmaking but high-grade ores have diminished, making it necessary to turn to low-grade ores, which need further beneficiation to upgrade the iron content. Biobeneficiation techniques such as bioleaching, bioflotation and bioflocculation have proven successful in iron ore processing. Consequently, these methods have emerged as sustainable alternatives to conventional beneficiation. The biobeneficiation processes occur in mild conditions using bioreagents and biosurfactants derived from microbes, and offer a reduction of chemicals used in processing. This potentially offers methods that are relatively energy efficient, cost effective and environmentally friendly while tackling the constraints of dwindling high-grade iron ore resources.

Sep 1, 2024