Search Documents

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity to drivability to safety. Accurate subsidence prediction, correct influence assessments and effective mitigation measures are the keys to ensuring the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures — such as road surface pavements, concrete slabs and transverse joints — vehicle dynamics, comfort level and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed, along with an application case.

By M. D. Heresy, H. F. Coward

"Whenever a manometer has been used for recording explosion pressures it has been calibrated under a series of static pressures. Whether the readings taken during the rapidly changing pressures of an explosion (dynamic pressures) truly represent the actual pressures therefore is an open question. The authors had hoped to solve this problem by conducting the calibration with the aid of known pressures, applied at about the ammo rate as in an explosion, for example, by means of a cylinder and piston, the piston being driven in by an eccentric cam at a rate which would be determined accurately by the shape and rate of revolution of the cam. If the rate of compression were great enough, then the pressure in the cylinder (to which the manometer is attached) could be calculated from the laws of adiabatic changes of pressure and volume. It seems highly probably, however, from H. T. Tizard's observations on pressure changes in a cylinder during rapid compression (55) 4/ that there is much heat loss, therefore pressure loss, in the very small interval of time during compression; although Tizard was able to estimate the amount thereof, he did so only by relying on his nanometer, which is exactly the procedure that the authors challenge on the grounds that the manometer was not standardized under the conditions of its use. Hence the authors were driven from this scheme of calibration to another, namely, comparing records of ono and the same explosion taken simultaneously on several instruments of as varied a type as possible. If 2 of a number of instruments agree, perhaps both are accurate; if 3 agree, probably each of the 3 is accurate; if 4 agree, it is almost certain each of the 4 is accurate.There was a second objective in the present work. If the Bureau of Mines and the B.C.D. (British Coal Dust) manometers differ in their records, then from a sufficiently comprehensive series of experiments it may be possible to coordinate the extensive results already obtained at the American and British stations.Thirdly, it was hoped to learn which is the best available instrument for observing the pressures of coal-dust and as explosions and, if possible, to indicate means for improvement in manometry."

May 1, 1935

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By K A Plumb

New structural studies in the Walker Fault Zone of eastern Arnhem Land are integrated with basin-wide reconnaissance observations, made to refine models for the structural evolution of the McArthur Basin and provide new insights into the nature of metal logenetical ly important pre-inversion phases of the basin's evolution. At least five principal events may be identified during the Proterozoic: The Tawallah Group and equivalents were deposited throughout the McArthur Basin during an extensional event. Rifting of an incipient Batten Trough occurred at this time, in a terrain characterised by orthogonal, linked extensional faults. Uplift and erosion of the Tawallah Group accompanied continuing extension and was penecontemporaneous with continuing deposition of the overlying Parsons Range Group, within a precursor to the Walker Trough. Dt (of the Walker Fault Zone) relates to a new rifting event, penecontemporaneous with deposition of the McArthur Group and its equivalents in the Walker and Batten Troughs. This rifting accompanied dextral strike-slip faulting along northerly-trending bounding faults, as a result of northwesterly-directed oblique extension, leading to pull-apart basins. D2 inversion of the Batten and Walker Fault Zones pre-dates deposition of the Roper Group. In the proposed model WNW-ESE directed shortening (D2.), accompanied by folding and thrusting, and by local development of cleavage in the Walker Fault Zone, is seen to be followed by northerly-trending sinistral faulting (D2b), about a SE to ESE-directed compression. D3 is basin-wide and post-dates the Roper Group. It is characterised by conjugate faulting and folding about ENE to NE-directed compression. The latest Proterozoic event to be identified (D4) comprises widespread north-trending strike-slip dextral faulting of Roper Group, coupled with N-S directed thrusting across the Urapunga Fault Zone and Murphy Inlier This is accompanied by late dextral reactivation of NNW to NNE-trending faults in the Walker and Batten Fault Zones.

Jan 1, 1994

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. Based on thermodynamic analysis, the present work discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extraction and low acid consumption. Rare earth extractions as high as 80 percent were achieved, while iron and thorium extractions were lower than 1 percent, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature.

By Noller B. N, McGill R. A

The Alligator Rivers Region has been the scene of one of Australia's most intensive environmental monitoring efforts since the current generation of uranium mining was mooted in the 1970s. Prior to mining, the local environment and the nature of potential impacts were not well known. The initial monitoring programs therefore included large baseline characterisation and research components. After some 15 years, water, soil and sediment monitoring programs have been reduced to a fraction of their early size, as the mining and natural systems became better known and characterised, and the actual nature of the environmental impacts were established. Modem techniques allow much more rapid and thorough identification of chemical species and elements of concern, allowing much more focused monitoring programs to be designed. In the 1980s data collection was emphasised at the expense of interpretation, and monitoring programs were maintained at much higher levels than were in fact required. It is now clear that investigations are important and should be distinguished from monitoring programs, and that the timely interpretation of investigations and implementation of recommendations can greatly reduce the effort and expense that can be involved in a monitoring program. Monitoring programs based on a sound understanding of potential environmental impact may then be efficient and cost-effective, yet provide sufficient information to assess the environmental impact of mining, guide further environmental protection measures when problems are detected, and demonstrate compliance with regulatory requirements.

Jan 1, 1994

By Liming Yuan, Isaac Zlochower, RICHARD THOMAS, Thomas H. Dubaniewicz, Teresa Barone

Mining vehicle manufacturers are developing lithium-ion (Li-ion) battery electric vehicles as an alternative to diesel-powered vehicles. In gassy underground mines, explosion-proof enclosures are commonly used to enclose electrical ignition sources to prevent propagation of an internal methane (CH4)-air explosion to a surrounding explosive atmosphere. Li-ion batteries can create pressurized explosions within sealed enclosures due to thermal runaway. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) measured thermal-runaway pressures of lithium iron phosphate (LFP) cells as a function of free space within sealed enclosures and observed an inverse power relationship. A well-confined cell produced 4260 psia (294 bar) of pressure during a thermal runaway, far exceeding minimum pressure containment specifications for conventional explosion-proof enclosures. Results indicate that adding enough free space surrounding LFP cells can reduce thermal-runaway pressures to levels below that expected for CH4-air ignitions. Measured thermal-runaway temperatures were below the minimum autoignition temperature of CH4-air.

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium, and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. This work presents a thermodynamic analysis of a monazite system and discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extractions and low acid consumption. Rare earth extractions as high as 80% were achieved, while iron and thorium extractions were lower than 1%, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature

By Sen S. K, Banerjee D. D, Nandy D. K

It has been stressed that the intrinsic spon- taneous heating characteristics of a coal is not enough in predicting spontaneous fire risk of a mine. The influence of extraneous conditions created from the system of mining operations are also to be reckoned with, A case study was made with a mine in Jharia field, India, being proposed to be developed under short wall method with complete extraction in 4-5 slices followed by stowing.

Jan 1, 1988

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By Henry Kreisinger, WALTER T. RAY

The investigation of the transmission of heat into steam boilers is one of several researches now being carried on by the Bureau of Mines that have for their object the testing of methods by which the mineral fuels in this country may be used more efficiently. A better understanding of the laws governing heat transmission into boilers will result in the design of more efficient boilers, and more efficient boilers will reduce waste in the use of fuel. The results of the investigations described in this report indicate that the conductivity of the heating plates of steam boilers is so high that the present steaming capacities can be tripled or quadrupled by forcing over the heating surfaces three or four times the weight of gases now passed over them. With well-designed mechanical-draft apparatus this greater weight of gases can be forced through the boilers at a small operating cost. It is possible to increase the capacity of many of the present boilers in this way without reducing their efficiency much; in fact by a proper arrangement of the heating surfaces the efficiency can be made higher than the present rating. The efficiency of any boiler can be increased by arranging its heating surfaces in series with respect to the path of hot gases. New boilers of high efficiency can be constructed by making the cross section of the gas passages small in comparison with the length. In Bryan Donkin's book, entitled "The Practical Physics of the Modern Steam Boiler," it is stated that James Watt obtained nearly as good an evaporation per pound of coal and per square foot of heating surface as is obtained now. The remark is probably true. At any rate, about the only decided superiority of the modern steam boilers over older types is in mechanical construction, and for this superiority credit should be given to the designers of machine tools quite as much as to the boiler engineer. The main reason for tardi- ness in boiler improvement probably lies in the reluctance of educated engineers to do the dirty and disagreeable work involved in boiler tests.

Jan 1, 1912

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

By Horace C. Porter, F. K. OVITZ

The various fuel investigations that were being carried on by the technologic branch of the United States Geological Survey were transferred by law on July 1, 1910, to a new federal bureau, the Bureau of Mines, that was authorized to continue the investigations and make public reports of the results. In consequence of this transfer, the following report is published as a bulletin of the new bureau. The United States Geological Survey had been engaged in analyzing and testing coals, lignites, and other mineral fuel substances under authority given by act of Congress. This work, now centered at the experiment station at Pittsburg, Pa., had its beginning in the operations of the coal-testing plant erected at the Louisiana Purchase Exposition in St. Louis, Mo., in 1904. The results obtained at that plant showed that the work of determining the fuel value of the coals and lignites in the United States with a view to increasing efficiency in their utilization would be incomplete if it did not include systematic physical and chemical researches into the processes of combustion. Hence in its later investigations the Survey carried on such re- searches, concentrating attention on those lines of inquiry which promised results of greatest economic importance. This bulletin is a report on an investigation of the volatile matter in several typical coals-its composition and amount at different tem- peratures of volatilization. As the investigation is still in progress and will doubtless include other coals than those already examined, the bulletin may be considered a preliminary report, stating the prob- lems studied, the methods used, and the results thus far obtained.

Jan 1, 1910

By GEORGE S. POPE

This bulletin is the third of a series a showing the results of ment purchases of coal according to specifications as to its quality and giving typical forms of proposals for supplying coal and general information relating to government coal purchases . Numerous calls for authentic information concerning the purchase of coal according to its heat value attest a growing interest in the subject. Many of the commodities of life have long been purchased according to specifications requiring chemical or physical tests , or both, to determine whether the material delivered meets the requirements , the price to be paid depending on the results of the tests . Until recent years coal consumers purchased coal merely on the statement of the dealer as to its quality , relying on his integrity and on the reputation of the mine or district from which the coal was obtained. It is surprising that the important question whether value was being received for the money expended was not sooner seriously considered . The purchase of coal by specification is an important step toward the conservation of our national mineral resources , for it results in an increased use of the lower grades of coal. The poorer coals find a market by competing with the better grades , not as to the price per ton but as to the cost of an equal number of heat units. This paper gives in detail the results of government purchases of coal for the fiscal year 1908–9 and the list of contracts with abstracts of specifications for the fiscal year 1909–10 , and summarizes the information on this subject obtained by the Survey. It is hoped that this information will promote a better understanding of the specification method of purchasing coal and furnish data valuable alike to coal dealers and coal consumers , so that equitable contracts can be more readily made.

Jan 1, 1910

By IRVINGC. ALLEN, W. A. Jacobs

Realizing the great importance and wide application of petroleum and its products for fuel,lighting and lubrication, and the absence of authentic and comprehensive information in the literature on the commercial value of American petroleums, the United States Geological Survey has for a number of years' been making analyses and other examinations of these oils and their products. In 1907 the technologic branch of the Survey began a study of certain economic problems having to do with the natural mineral oils. The prime object of the investigations was to determine the economic value of the petroleums and natural gases in the United States with special reference to the supplies in the public lands, and to ascertain how these resources could be utilized in the industries withleast waste and greatest efficiency. This work, which is now being conducted by the petroleum section of the Bureau of Mines under authority of the act of May 16, 1910, will include the collection at the wells and refineries of information as to the following details: Facilities for handling and storage at the wells. Facilities for transportation, whether by pipe line, rail, or water. Distance to the nearest port or center of industry and time necessary for delivery. Facilities for storage at such point of delivery. Suitability of the crude oil for fuel, or the treatment necessary to convert itmost economically into the best fuel. Best processes of refining or of converting the crude oil into its many products. The examination of these products. The utilization of the by-products and residues of the refineries. The collection of adequate and reliable samples, and the complete chemical and physical examination ofthese samples in the laboratory.

Jan 1, 1911

By Clarence Hall, J. J. Rutledge

Many of the fatal accidents in coal mines have resulted from the Explosives used in Use of explosives for breaking down the coal. These accidents have resulted both from the use of explo- sives that were not suitable and from the careless or improper use of suitable explosives. Investigation has shown that one of the commonest causes of dis- astrous explosions in the coal mines in this country has been a blown- out shot of black blasting powder or dynamite. The dangers that attend the use of these explosives were perceived several years ago, and in consequence the attention of powder manufacturers was directed to the production of explosives that would be less liable to ignite inflammable gas or dust. The manufacturers have been so successful in their efforts that it is now possible to obtain explosives which yield much shorter and quicker flames than black blasting powder or dynamite, and hence are much less dangerous to use in fiery or dusty coal mines. of explosives. To find out which of the many grades of short-flame explosives Government tests have the qualities that render an explosive most effective and least dangerous for mining coal, the United States Government established a testing station at Pitts- burgh, Pa., in 1908. This station is now under the charge of the Federal Bureau of Mines. Before the station was opened a state- ment of the requirements that the explosives in question would have to satisfy was drawn up and sent to manufacturers. A number of these sent explosives to be tested, and on May 15, 1909, a list of the explosives that had passed the tests was published. Since that date other brands of explosives have been tested and three more lists have been issued. The latest list, published in Miners' Cir- cular 2, Bureau of Mines, contained the names of no less than 71 explosives that had passed the tests prior to January 1, 1911.

Jan 1, 1912

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By Clarence Hall, S. P. Howell, W. O. SNELLING

The explosives used in coal mines not only occasion accidents such as occur in the use of explosives elsewhere, but they frequently cause widespread disasters by igniting explosive mixtures of mine gas and air and of coal dust and air, or both. In addition, the firing of ex- plosives so shakes the walls and roofs of the mines as to cause falls, with their attendant casualities. Considering the large number of explosives and their wide range in composition and properties, it is obvious that certain of them should prove more suitable for use in coal mines than others. The problem is to determine which explosives are the most suitable for this purpose and the precise conditions under which they may be used with the greatest safety. Of course this problem could be worked out in actual mining, but experimental investigations when accompanying commercial opera- tions are hazardous and slow. To obtain the information sought, in the speediest and most economical manner, laboratory methods must be resorted to. The adoption of such methods began about 30 years ago with experiments in an iron gallery mounted on wheels, at Zwickau, Germany. This laboratory method of attacking the prob- lem has so commended itself that it has not only been repeated else- where in Germany but has at intervals been officially adopted, with many modifications and additions, by the Governments of Belgium, Austria, France, and Great Britain. Such was the status of coal-mine investigations in Europe when in 1904, an organization in the Geological Survey, which in 1907 be- came the technologic branch, was created to investigate the mineral- fuel resources of this country. At that time no division of the Na- tional Government had official cognizance of conditions existing in our mines, but through its system of collecting fuels for tests the technologic branch was forced to recognize that coal-mine accidents are a factor that must be reckoned with in determining the extent and availability of our mineral-fuel resources. This became so apparent, and it was so obviously a function of this branch to make a systematic research as to the cause and prevention of such acci- dents, that in July, 1907, experts were appointed especially to deal with this problem. As a result, not only was Bulletin 333, on Coal- Mine Accidents: Their Causes and Prevention, prepared and pub- lished, but through personal inspection of foreign testing stations, and a study of their reports and the critiques of their methods and operations, definite plans for the establishment of such a testing station in this country were formulated. In the latter part of 1907, four grave disasters occurred in close succession consequent on explosions in the Monongah mines in West Virginia, where 368 men were killed, the Darr mine in Pennsyl- vania, where 160 were killed, the Naomi mine in Pennsylvania, where 34 were killed, and the Yolande mine in Alabama, where 61 were killed. These frightful disasters so quickened the public con- science, and so plainly demonstrated that both humanitarian and economic needs demanded that steps be taken to prevent the re- currence of such accidents, that in 1908 Congress made a special appropriation for an investigation as to the "causes of mine ex- plosions." A similar appropriation was made in the following year. By act of May 16, 1910, the Bureau of Mines was created "to make diligent investigation of the methods of mining, especially in relation to the safety of miners, the use of explosives, the prevention of accidents," and other matters relating to mining. Therefore, these investigations are at present conducted in obedience to an organic act instead of being dependent solely upon special appropriations. The first appropriation became available July 1, 1908. Through the courtesy of the War Department a portion of the grounds and buildings of the arsenal at Pittsburgh was granted for the use of the technologic branch of the United States Geological Survey. Work was immediately begun in procuring and erecting the necessary instru- ments and appliances for carrying out the desired tests and inves- tigations and in adapting the existing buildings or in erecting new structures to contain the apparatus. The Pittsburgh testing station was officially opened and regular work was commenced on December 3, 1908, the apparatus and appliances having been tested, the force drilled in their use, and the equipment and methods inspected and passed upon by foreign experts.

Jan 1, 1912