Search Documents

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By P W Haines

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By J Siliézar

The Ernest Henry Mine (EHM) is situated 38 km north-east of Cloncurry in the Mount Isa – Cloncurry mineral district of northwest Queensland. The EHM orebody is an iron oxide copper gold deposit with an average grade of one per cent copper, 0.5 g/t gold and 23 per cent magnetite, with current reserves of approximately 88 Mt.The copper concentrator is a single line plant with a nominal throughput rate of 1300 tonnes per hour. An average of 350 000 tonnes of concentrate is produced each year containing around 100 000 tonnes of copper metal and 120 000 troy ounces of gold.In December 2009, Xstrata Copper announced approval of a $589 M investment to extend the life of EHM to at least 2024, through the transformation of open pit mining operations to a major underground mine together with the construction of an associated magnetite extraction plant.The EHM magnetite plant extracts the magnetite from the copper concentrator’s tailings stream. It will produce approximately 1.2 Mt of magnetite concentrate per annum at full capacity for export to Asia, making EHM Queensland’s first iron ore concentrate exporter. Construction of the magnetite extraction plant commenced in July 2010 and was completed in January 2011.This paper gives an overview of the development of the EHM magnetite extraction plant flow sheet from the early mineralogy and laboratory test work through to the plant commissioning and early operation of the base plant. It has a major focus on the commissioning learnings from the plant start-up and includes a review of the operational performance of the plant versus original design and expectations.

Jul 11, 2011

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll on the U.S. coal mining industry. Recent health surveillance data indicate that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied to reduce dust levels. An overview of CWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

By G Phillips

The Merlin project is situated 130 km south of Cloncurry in North West Queensland, Australia. It is located within the Pre-Cambrian Mt Isa Inlier and is grouped within the Eastern Fold Belt. The host rocks are metasedimentary rocks of the Proterozoic Kuridala and Staveley Formations adjacent to the Mount Dore Granite.Merlin zone represents part of the Mount Dore polymetallic deposit containing copper, zinc, silver, gold, lead, cobalt and most recently has been found to host molybdenum mineralisation. This is intimately associated with economic grades of rhenium, a naturally occurring metal that is an important component of high temperature aircraft engines. The host rock sequence is a 200 m thick zone of metasediments sandwiched between competent granite in the hanging wall and brittle quartzite in the foot wall. A distinct shear marks the contact between the granite and metasediments. The host rocks are comprised of three main rock types: black shale, phyllite and altered banded calc-silicate.Mineralisation dips to the east at approximately 45° in a package of fine grained pelites and banded calc-silicates. The top 150 m of the sequence is typified by black shale and phyllite. The lower 50 m is typified by pink banded calc-silicate. The main molybdenite zone is located at and parallel to the pelite-calc-silicate contact. Down dip, the zone splits into two or three veins hosted by the calc-silicate rock suite and haloed by thin, steep dipping, stylolitic molybdenite veinlets.The deposit was discovered in 2008 by routine infill reverse circulation sampling conducted for the Mount Dore copper deposit. One hole penetrated below the main target Cu horizon and intersected visible molybdenite. During 2009 and 2010 a 50 × 50 m diamond drill pattern delineated a total mineral resource of 6.7 Mt @ 1.3 per cent Mo, 23g/t Re, 0.3 per cent Cu (mostly Indicated Mineral Resource with minor Inferred Mineral Resource). The resource has been estimated using ordinary kriging within grade domains. Access to the deposit has commenced via a decline and production through the nearby Osborne flotation concentrator (70 km south) is expected in 2012. All facilities and resources are fully owned and operated by Ivanhoe Australia Limited, a public listed company on the Australian and Toronto stock exchanges.

Aug 22, 2011

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By Nicolin Govender, Pramod Kumar, Raj Rajamani

Mill power models have been used in a variety of ways in industrial practice since power directly equates to throughput and fineness of ground product. We first start with Hogg-Fuerstenau Power Model and show how this model successfully predicted the power draw of many grinding mills in several mining operations. Then, we show how this model was on the verge of being able to predict the influence of lifter design on power draw. Next, we describe the discrete element model and how it overcame the issues faced by the previous power model. Using a DEM software known as Millsoft, we show the influence of lifter design geometry on power draw and analyze the power draw of rubber lifters versus the steel lifters via several case studies. As years passed, the two-dimensional discrete element model imbedded in Millsoft is superseded by three-dimensional discrete element method. Due to the gigantic computational power of graphic processing units, new computational codes that can do the tumbling motion along the entire length of the mill has come about. Here, we show the predictive capability of Blaze-DEM for ball and SAG mills.

By D J Maconochie

The use of rock bolts as permanent support has been prohibited by client specifications in several recent large tunnel projects in Australia. The justification for this appears to lie in concerns with proper and verifiable installation procedures rather than concerns with the intrinsic durability of the corrosion protection systems. However, in civil tunnels, preventing the use of permanent rock bolts for long-term support results in the use of cast in place concrete lining which in some instances would otherwise be unnecessary.

Mar 8, 2011

By M. A. Cristovici

"In the last few years CANMET has taken the initiative by investigating the possibility of reactivating abandoned old tailings dumps (for gold production) which would be of potential economic interest across Canada.Nova Scotia was one location where numerous gold processing plants were in operation in the early days. A survey of the old tailing dumps was conducted and some areas of interest were selected. Among them were the sites identified as Lake Charlotte and Forest Hill.Ore samples collected from those tailing ponds were examined for their chemico-mineralogical composition and investigated for gold extraction. Three technological concepts were tested: flotation, direct cyanidation and flotation followed by cyanidation of the flotation concentrate. The combined flotation- cyanidation variant, yielding a gold recovery in the range of 90%, was recommended for processing the tailing ore.Pilot-plant runs carried out by a commercial testing firm (data not included in this paper) confirmed the conditions and results of CANMET's technology.As a result a consulting-engineering firm designed the processing plant which is expected to begin operation in the near future.IntroductionIn the last few years CANMET initiated a research program to locate in Canada, abandoned gold-silver tailing dumps of potential economic interest and to explore the possibility of recovering the precious metals from these old deposits by modern techniques.A literature search revealed that the first production of gold in Canada was recorded in British Columbia in 1858 and that, production prior to 1900 was essentially restricted to the Yukon, British Columbia Nova Scotia and Quebec. During the early 1900s, Ontario, Manitoba and the North West Territories joined the ranks of the gold producers.Early milling and recovery methods were mainly restricted to sluice boxes, gravity stamps and amalgamation. Froth flotation and cyanidation were introduced at about the turn of the century.Recovery of gold at plants using flotation and cyanidation was very good, therefore the tailing ponds resulting from those operations would, very likely be of little or no economic importance. However, the gold recovery at the amalgamation and gravity concentration plants appeared to be lower, indicating the possibility that significant amounts of recoverable gold would have been carried with the tailings to the dump sites."

Jan 1, 1986

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By E J. Cowan

Efficiency demands that mine geologists devote the most time to tasks where they can have the biggest effect on production. One of the most time-consuming tasks is geological interpretation of the orebody and turning this into a block model for the planning engineers.The current best practice for mines that require a geologically constrained resource model involves capturing the interpretation of geologists as three-dimensional (3D) wireframes. However, there is significant overhead in the production of valid wireframes from sectional and plan interpretations. This overhead consists of the mundane tasks of digitising polylines, then building 3D wireframes and validating them. While software can simplify this task, the current process is not the best use of a geologist’s time. Under time pressure exerted by planning engineers and the time required for modelling from polylines, geologists are forced to roll-up the presence of other elements or impurities into the interpretation and encode them in the polylines, even though it is often desirable to consider these other factors separately.While it might seem unlikely that mine geologists can produce constrained geological models without the intermediary of wireframes, the technology to accomplish this is getting closer.In this paper, the results of a trial at the Savage River magnetite mine, which is owned and operated by Grange Resources Ltd, are reported. The trial was for a ‘direct-to-block’ implicit geological modelling method. The focus was on creating a geological attributed block model from drill hole geological log data; resource estimates were not determined. The categories modelled were air, waste, low-grade ore, medium-grade ore, and high-grade ore. The block model outputs either resulted in a proportional block model (categories expressed as percentages within equivolumetric blocks) or a sub-blocked model (parent block and one sub-block), which is the preferred block model output at the Savage River mine. When compared to the traditional best practice modelling method, which takes 43 work days, the wireframe-free modelling method took only 26 hours from initial modelling, using both exploration and grade control data. An update using appended drill hole data is achievable within one day. These results represent time savings of more than one order of magnitude compared to the traditional workflow, and, as such, these figures merit serious consideration for the use of the direct-to-block modelling approach at other operations.With these time savings, geological and estimation models can be kept updated constantly; geologists will not need to set aside two months for quarterly or half-yearly modelling of the drill hole data for resource review. Such dramatic time savings will allow for the better use of highly skilled geologists, who are in short supply in the current market, and will also impact directly on downstream mining engineering workflows.

Aug 22, 2011

By P. O. Parfitt

The Critical Path Method has proved its usefulness at Mcintyre Porcupine Mines Ltd. This paper illustrates the techniques of network construction and analysis, and the application of the method at the Mcintyre copper mine to various projects in the gold mine. C.P.M.'s use in a mill maintenance project is also discussed.

Jan 1, 1966

By AUIMM AUIMM

Continuous Improvement The Council of the AusIMM should expedite the introduction of a continuous professional education policy along the lines of that to be proposed to you by David Pollard today. The Education and Accreditation Committee must continually review the training needs of the next generations of mining industry professionals. It should continue to demand and encourage the creation of the schools for the training of such people. The AusIMM could even put greater onus upon university researchers to accredit university post graduate degrees.

Jan 1, 1994

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By Flavelle IV

A survey is made of changes in the technical status of a number of western world copper extraction and refining operations over the past 20 years. Specific developments in pyro- and hydro-metallurgy and refining practices are identified together with factors in the changing environment of the industry which has influenced their adoption. Nickel extraction and refining is similarly discussed.The replacement of traditional technology by more attractive alternatives has occurred in a considerable number of operations. The develop-ment and status of new continuous smelting processes, advances in hydrometallurgy and refining innovations which emerged during the 1960s and early 1970s is discussed. The varying experience in commercial acceptance of these new technologies is noted.Finally some possible future directions are canvassed for both operators and the research and development institutions.

Jan 1, 1985

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

 This research project explored the viability of a new mining technology — thermal fragmentation — in narrow-vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation as well as one of an existing method used for narrow-vein mining. Comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs as well as increased productivity and ore recovery meant that the new method would improve the financial performance of any operation.