Search Documents

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By R C. Morris

Secondary microplaty haematite in its variety of styles and generations is the defining component of the high-grade banded iron-formation (BIF)-hosted iron ores of the world that are dominated by martite (M; - haematite pseudomorphs after magnetite). The term microplaty haematite (mplH) was introduced during the CSIRO-AMIRA 1976-1994 iron ore program, and was used to differentiate the then main export martite-microplaty haematite (M-mpl H) ore types of Tom Price-Whaleback and Paraburdoo (Paleoproterozoic), from the newly exploited, more prolific supergene martite-goethite (M-G) ores (Mesozoic-Paleocene) of the Hamersley Province that are now the major Hamersley iron ore exports.Morris (1980, 1985) suggested that the most important genetic factor that distinguishes the two main ore types was regional metamorphism of Paleoproterozoic M-G ores at temperatures normally related to diagenesis (ca 80 - 100°C). As temperatures increased, mplH grew in goethite both spontaneously as well as by nucleating on martite and other pre-existing haematite. Because the conversion of goethite to haematite involves a ~27 per cent reduction in volume, the crystals probably grew within microvoids of their own creation, with iron transfer through water resulting from the process itself, a local hydrothermal process requiring no introduced hypogene fluids.Barley et al (1999) and Taylor et al (2001) concluded instead that oxidation of introduced siderite in hydrothermally metasomatised BIF ‘protore’ resulted in mplH + ankerite by reaction with heated meteoric fl uids. This postulated ‘protore’, still preserved locally at Mt Tom Price, was described during the CSIRO-AMIRA program as local post-ore BIF metasomatic residuals. These new hypogene-meteoric concepts for M-mpl H genesis have formed the basis for a range of varying local and international models that currently dominate the literature of iron ore.No valid petrographic data supporting the hypogene-supergene modelling was found but petrographic images of goethite-related mplH growth in a range of different environments are shown.

Jul 11, 2011

By Kamran Esmaeili, MINGLIANG TANG

An understanding of the spatial and temporal variations of surface moisture content over a heap leach pad is essential for leaching production and to achieve a high ore recovery. The current leach-pad monitoring and data-collection practice remains highly labor intensive and exposes technical staff to cyanide solution, a hazardous material. To address these challenges, we propose using unmanned aerial vehicles (UAVs) equipped with thermal imaging sensors to remotely obtain image data with high temporal and spatial resolution for monitoring the surface moisture distribution over heap leach pads. A field study was conducted over a sprinkler-irrigated heap leach pad at El Gallo gold mine in Sinaloa, Mexico, and the acquired data were used to generate moisture distribution maps of the heap leach pad’s surface. The created moisture maps provide direct visualizations of surface moisture variation over the surveyed area. Such graphical results are effective tools for inspecting heap-leaching operations.

By J Wheeler

The objective of this paper is to examine the operation of high frequency screens in closed circuit grinding, where the outcomes achieved indicate favourable economic gains at the comminution stage and downstream processes, including flotation, dewatering, and filtration operations. The classification process in grinding circuits has been slowly evolving within the last century. The history of classification devices brings to mind rake classifiers and spiral classifiers, which although having higher efficiencies compared to hydrocyclones, were not able to keep pace with the evolution of concentrator equipment treating higher tonnages. This higher tonnage throughput has tended to drive the concept of utilising hydrocyclones as the classification stage in closed grinding circuits. The comminution process is commonly the most energy intensive stage of mineral processing. Researchers have determined that the classification stage in the comminution process has the greatest potential for improvement. This paper is intended to inform mineral process engineers of the benefits that high frequency screens offer over hydrocyclones. This will be done by reviewing the purpose for the evolution of classification in the comminution process, documenting past and recent studies, and explaining the modern technology that is currently available.

Aug 8, 2011

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By M Sparrow

The Victoria Park Tunnel project is an inner-city alliance project in central Auckland, New Zealand. The existing two-directional viaduct will be modified to single-direction flow, and a new northbound 440 m cut and cover tunnel will be constructed beneath Victoria Park. Three-dimensional (3D) visualisation media were used to communicate key design innovations to stakeholders and the general public. The 3D visual material has proven a useful tool for informing motorists of a new safety barrier method adopted for traffic management.This presentation will explain how 3D visualisation was incorporated in the project and will showcase the 3D visualisation media created for the project.

Mar 8, 2011

By J D. Lubben

Hibbing Taconite is a Lake Superior-type granular magnetite taconite deposit occurring within the Biwabik Iron Formation along Minnesota’s central Mesabi Iron Range. The deposit is situated on the northern margin of the Proterozoic Animikie Basin. The deposit strikes northeast, dips gently southeast, and occupies 10 km of strike length. Mining focuses on 50 m of granular cherty and laminated slaty taconite within the Lower Cherty member.Ores generally consist of a quartz, magnetite, siderite, ankerite, minnesotaite, stilpnomelane, and haematite mineral assemblage. Processing is optimised by exploiting the physical and chemical variations that exist between three major ore types. Taconite ore averages 20 per cent magnetic iron (MagFe), 27 per cent weight recovery (WtRec) and produces a final concentrate with 4.5 per cent silica (SiO2). Since 1976, production has totalled approximately 237 million long tons (Mlt) of pellets (8 Mlt per year rated capacity).Ore processing uses a simple fl ow sheet of autogenous grinding (<0.044 mm) followed by two phases of wet magnetic separation, fi ltering, limestone/bentonite addition, balling, and firing to create pellets averaging 66 per cent total iron. A Liberation Index (LIS) is used as a primary guide for ore grading and metallurgical control. Grind requirements, magnetite liberation and silica grade are closely monitored to ensure plant optimisation and product quality.A recent program of benefi ciation of low-grade ores by in-pit crushing and dry magnetic cobbing has demonstrated that low-grade ores (<17 per cent MagFe, <25 per cent WtRec) can achieve a signifi cant metallurgical upgrade (up to 25 per cent MagFe and 40 per cent WtRec). This operation recovers 60 per cent of the total crushed volume, and has a calculated effi ciency factor (magnetic iron recovery) of 79 per cent. This paper discusses the benefi ts of this upgrading and its effects on ore blending and processing.

Jul 11, 2011

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat, A. J. S. (Sam) Spearing

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. Initially, ASTM A615 grade 60 steel roof bolts, which are the most commonly used bolt material in the United States, were tested with and without stresses in a simulated underground coal-mining environment for approximately six months. This paper mainly discusses the test system, protocol and system shortcomings, and makes recommendations based on the observations and results.

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

This study examines a process for the recovery of precious metals from difficult minerals that exhibit refractory characteristics to cyanidation: low extraction of metals and high consumption of leaching reagent. A mineral sample from Monte del Favor Mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay and atomic absorption spectroscopy (AAS). Two stages of leaching were carried out, first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent along with sulfuric acid (H2SO4), and second to dissolve gold and silver with hydrochloric acid (HCl) and sodium hypochlorite (NaClO). The results show extractions of around 96 percent for manganese (Mn), 98.73 percent for silver (Ag) and 83 percent for gold (Au). The usefulness of high acidity and Na2SO3 to obtain better results in Mn and Ag leaching are discussed along with the roles that HCl and NaClO play in Ag and Au dissolution values.

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By P Ramsaywok

The use of saline water for mineral beneficiation in arid regions is general practice and also the case with Exxaro Namakwa Sands, situated on the west coast of South Africa. Although it is ‘cost effective’ to use sea water for mineral beneficiation, downstream process separation efficiencies may be negatively affected. This is more specific to surface dependent separation techniques such as electrostatic and high tension (HT) separation. If minimal fresh water is available then, proper washing is often neglected. Salt crystals can form on particle surfaces during the drying process before electrostatic separation.This paper describes a study that has been conducted to determine the effect of upfront salt water processing on downstream electrostatic/HT separation. The study indicated that minor quantities of salt can cause the separation efficiency to decrease substantially.

Oct 5, 2011

By K.H. Song, H.T. Son, H.S. Kim, W.Y. Kim

In order to evaluate the grain refining and mechanical properties due to severe plastic deformation (SPD), this wrok was carried out. Convential rolling (CR) and cross roll rolling (CRR) as a SPD method were introduced, and NI-20Cr alloy as an experimental material was chosen. The materials were cold rolledto 90% in thickness reduction ans subsequently annealed at 700oC for 30 min to obtain the fully recrystallized microstructure. For annealed materials after cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). CRR process was more effective to develope the grain refinement relative to CR process, as a result, grain size was refined from 70 um in initial material to 4.2 um (CR) and 2.4 um (CRR), respectively. These grain refinements directly affect the mechanical properties improvement, in which microhardness and yield and tensile strengths were significantly increased than those of initial meterial.

Jan 1, 2012

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By D FitzGerald

A critical component of any new tunnel design in a complex geological setting is the development of an integrated three-dimensional (3D) geology model with a full set of geotechnical properties of the rocks present. A novel means of predicting the geology based upon sparse observations of structural geology at the surface and from drill holes has been developed and used in several major tunnel studies in Europe.An example of this is the Lyons-Turin twin rail tunnel which is still in a development phase. This tunnel has been in planning and development for over 15 years already. An important aspect of this work is to characterise geological uncertainty along various possible tunnel paths as an input into early design optimisations for time, cost and risk avoidance strategies. Once the tunnel works commence and more detailed geological data is collected by daily mapping, progressive refi nement of the geological model is desirable; geological conditions still to be encountered can be more accurately predicted. Faults and their offsets, dykes, geological unconformities, folding, as well as standard sedimentary processes are all correctly modelled in the software. It is important to allow for seamless interchange of geological models at various scales with CAD workflows so that sufficient detail can be readily accessed at the required scale. Also, the proposed tunnel in its correct geometry can become a ‘section’ in its own right. Progressive detailed local geology models in the vicinity of the advancing head are created from the regional scale work by cutting and pasting a starting model, then adding all the extra detail for the required engineering geology work.For all rocks, most standard geotechnical quantities such as sonic velocities, Young’s modulus and Poisson’s ratio are handled. These and any other phenomena from borehole observations can have variograms calculated and stratigraphically constrained estimations made in a least biased geostatistical manner, in advance of the tunnel. RQD, or a prediction of rock fractures, is handled by the faulting and folding modelling facilities. This is probably the more interesting issue to pursue, as the fractal nature from small scale fractures and joints, to large-scale faults, can now be characterised more convincingly.

Mar 8, 2011

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By C Rizos

Many of the ‘new paradigms in mining’ and notions of ‘sustainable mining’ have at their core the requirement for reliable, continuous centimetre-level positioning accuracy to enable increased automation of mining operations. The deployment of precision systems for navigating, controlling and monitoring machinery such as drills, dozers, draglines and shovels with real time position information increase their operational efficiency, and reduce the need for humans to be exposed to hazardous conditions. The Global Positioning System (GPS) is the best known, and only currently fully operational, Global Navigation Satellite System (GNSS) providing positioning capability anywhere in the globe, on a continuous 24/7 basis, with accuracies ranging from the dekametre-level to the sub-centimetre-level depending on hardware and operational configuration. Despite this versatility, GNSS cannot satisfy the high accuracy positioning requirements for many applications in mine surveying, and mine machine guidance and control. The reason is that increasingly open cut mines are getting deeper, resulting in a reduction of the ‘sky-view’ necessary for GNSS systems to operate satisfactorily. Yet, to date there have been no viable alternatives to GNSS that can be deployed in mine environments that can meet the challenging requirements in open cut mines.Locata Corporation, a Canberra-based company, has invented a terrestrial high accuracy positioning system known as ‘Locata’ that can augment GNSS with extra terrestrial signals to permit cm-level positioning accuracy even when there are insufficient GNSS satellite signals for reliable positioning and navigation. Locata relies on a network of synchronised ground-based transceivers that transmit positioning signals that can be tracked by suitably equipped user receivers. Hence Locata can be considered a new type of ‘local constellation’, able to provide high accuracy positioning coverage where GNSS fails. This paper introduces some of the technical aspects of this Australian technology and describes tests conducted by Leica Geosystems over the last few years at Newmont Boddington Gold in Western Australia. A recent news announcement by Leica Geosystems (12 January 2011) has confirmed that their new mine management system will have combined GNSS + Locata positioning capability – the first commercial product that integrates GNSS and Locata capabilities into a single high accuracy and high availability navigation device for open cut mine machine automation applications.

Nov 22, 2011

By Taghi Sherizadeh, Paul Brooks, Dogukan Guner, Samuel Nowak

Large excavations are well known to result in rock mass deformations which can present challenging situations for mine personnel. Most of the currently available ground movement monitoring devices fail to adequately provide mine operators with highly accurate and meaningful insights into rock mass deformation or displacement. The use of distributed fiber optic sensors (DFOS) in industries such as oil and gas and civil engineering has shown the potential of these sensors to deliver real-time, highly accurate, and long-range distributed strain measurements with great success. However, the use of these sensors in underground mining is limited to a few case studies.