Search Documents

By Yi Luo, Jian Yang, YUJIA LIAN

Scale physical models, constructed according to the principle of similarity theory, are widely used to simulate the mining disturbances to surrounding strata and to evaluate the effectiveness of implemented ground-control techniques. This technique has also been used for studying mining-induced surface and subsurface subsidence. The movements of the observation points installed on the physical model at different mining stages are currently measured using a total station, which is time consuming and inaccurate, especially on small-scale models.

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By K Ionkov

The oolitic iron ore reserves in Lisakovsky, North Kazakhstan represent quite a challenging deposit both from a technological and from a resource point of view. The difficulties in processing such types of ore are connected with the extremely fine dissemination of phosphorus and gangue minerals inside the oolitic formations. The goethite crystals are cemented in their structure by aluminosilicates with quartz and other gangue minerals and dissemination is so fine that they are not separable by physical methods. The laboratory tests performed for dephosphorisation show that the combination of alkaline roasting followed by low intensity magnetic separation and acid leaching enables the obtaining of high grade iron concentrate. The magnetic separation performed ahead of leaching is effi cient as a means of buffering the high pH by washing out the soluble salts and the excess of base and after leaching facilitates the removal of secondary liberated gangue minerals in the non-magnetic fraction. As a consequence, phosphorous content is dropped to a more acceptable level for the ferrous metallurgy and iron grade and recovery reach 61.6 and 80.8 per cent respectively.

Jul 11, 2011

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluates the effectiveness of similitude theory in predicting the draft of a rubber tire loader’s bucket during initial penetration. The work uses 1:16 and 1:8 scale models of an 18-t capacity load haul dump, scaled with the Buckingham Pi theorem, to evaluate the prediction of draft and penetration under different operating and different dynamic conditions. We hypothesized that the observed relationships between draft and longitudinal penetration and the operating and dynamic conditions will hold true for an upscaled model. Similarly, we hypothesized that the results of experiments conducted with the smaller scale model should predict the draft on an upscaled model.

By Yuting Xue

The classification of rock and coal will assist in automated coal rib rating and shearer horizon control, and is studied with machine learning techniques in this work. A database of rock and coal images is created by filtering photographs taken by researchers from the National Institute for Occupational Safety and Health (NIOSH). The classifier was trained with patches extracted from the coal and rock images, and an accuracy score of 0.9 was obtained. The trained classifier was then applied to classify rock from a new coal rib image with three rock layers of different thicknesses, and good agreement was achieved. The results demonstrate that it is promising to use machine learning techniques and rib images for rock and coal classification.

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By A M. Avis

This paper presents an overview of recent developments in the Environmental Impact Assessment (EIA) process to provide the background for a more detailed analysis of environmental and social constraints that the Heavy Mineral Mining industry has encountered over the past decade. Four cases studies are reviewed to provide a context for further analysis and identification of cross cutting environmental and social issues that either resulted in the projects not proceeding, or in the Australian case study, places existing operations under significant pressure from anti-mining lobbyists. The Xolobeni project, from the Eastern Cape in South Africa, is presented as the primary case study because it is recent, topical, and accessible; and raised numerous issues related to mining in a sensitive environment. A proposal to mine an area adjacent to the Okefenokee swamps in 1997 was also met with strong opposition from various environmental groups in Georgia, USA. This case study is briefly reviewed to further understand what ultimately resulted in the project not proceeding. Opposition to mining at North Stradbroke Island is reviewed to identify current issues more applicable to a developed country. A further review of a strategic assessment undertaken at Wavecrest, Eastern Cape, South Africa is provided in support of possible solutions to the challenges identified in the case studies. Important common themes were identified, including in some cases unfortunate timing of the environmental studies, but in all cases opposition was due to ecological sensitivity, landscape quality and sense of place. In one case study limitations to the EIA process included inadequate detail in the specialist investigations and insufficient information on mitigation. In all cases public participation was a limitation. It was either insufficient; flawed through possible bias; too ‘top down’ and required engagement with mobilised, motivated lobbyists. There was also insufficient investigation of social impacts, particularly amongst rural communities directly affected by a project. Generally alternatives were inadequately considered, a recognised limitation of project level EIA. It is concluded that the EIA process should be started as early as possible (at prefeasibility), and that investigations should be expanded from a typical fatal flaw assessment to one that applies methodologies used in strategic assessment. In particular, opportunities and constraints of the natural and social environment should be assessed in the context of the mining option as well as other options, to allow for a more meaningful assessment of alternatives. Public participation must form an important part of this initial study, despite the potential risks associated with public engagement at an early stage in the project. The application of the IFC Performance Standards; and expanding the scope of the EIA into an environmental, social and health impact assessment will lead to a more rigorous procedure, and result in more defensible products which could successfully unlock the key to the resources in these sensitive areas.

Oct 5, 2011

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modeling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. The test results validated the feasibility and rationality of the coupled FD-DE method for modeling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modeling experience for investigating the shear behavior at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

By Z U Bajwah

During the Palaeoproterozoic, a large number of granitic intrusions were emplaced in the various parts of the Pine Creek Geosyncline (PCG). In the central region, the granitic magmatism is represented either by the coalesced mass, eg the Cullen Batholith, or individual plutons such as the Mount Bundey Granite which together with the Mount Goyder Syenite intrude the metasedimentary strata, causing wide spread contact aureoles. Some of these granitic intrusions are temporally and genetically related to gold (and less commonly base-metals) mineralisation present in the adjacent metasediments. These plutons are characterised by the presence of biotite and homblende which appear late in the paragenetic sequence. Electron microprobe analyses of biotite and homblende show that these minerals are poorly to moderately zoned. Biotites are characterised by a decrease in Fe/(Fe + Mg) ratios when plotted against AIVI. Similarly a modest decrease in Ti from centre to the margins of the biotite crystals has also been observed. Furthermore, an increase in Mg/(Mg + EFe) ratios from centre to the margins as well as in mafic to felsic rocks is also apparent. On the other hand, homblendes from the granitic bodies display less well marked trends and are poorly zoned. However, they show systematic increases in Mg/(Mg + EFe) ratios, and decreases in Fe, Al"' and Fe/(Fe + Mg) ratios, when plotted against Si. Magnetic susceptibility measurements on powdered samples of the plutons give results characterised by high values ranging from 0.8 x 10-4 to 2.0 x 10-3 emu/g which place the granites in magnetite- series field. This indicates that the oxidation state of the magma was high during crystallisation. The range of chemical compositions of the mafic phases indicates a rise in the oxidation state of the magma as it progressively became saturated in H20-volatiles and other metals, not partitioned into the earlier crystallised phases in the final stages of magma consolidation. These variations in chemical compositions also indicate that initially fOz was high and became progressively higher during fractional crystallisation of magmas; this subsequently led to the emanation of hydrothermal fluids responsible for the mineralisation in the adjacent metasediments.

Jan 1, 1994

By V. H. Valenzuela

Materials in process or in stocks are quite relevant items in almost every plant, particularly in mining operations, where efficiency in rate of recovering material of interest becomes a key issue when production costs are evaluated. A manager requires information to do an effective use of the resources, especially when raw materials are involved. Losses associated to leaking, efficiency in the transformation process, performance of equipment, and operating conditions are a short list of items which must be properly identified and evaluated. Operations supervisors require information in order to keep key process variables under control. Because of these information needs, it is absolutely necessary to carry on a series of activities related with installation and maintenance of measuring equipment, sampling equipment, sample preparation, chemical analysis, statistical analysis, data handling and reports generation. These pieces of data must be managed on a wise manner in order to get the most of it, keeping always on mind data reliability. Normally, information related with metallurgical balance and even more, the metallurgical balance concept, is handled under an accounting criteria which does not allow dealing with the real world. This situation happens because the criteria utilized do not consider aspects such as bias and uncertainty associated with every measurement that affect the quality of the information and therefore conclusions drawn from it. The purpose of this paper is to give a few rules, necessary to follow, in order to develop an adequate Metallurgical Balance System for an operational point of view. The Gaussian approach for error propagation is used as a basis, allowing one to know the actual uncertainty of the balance and the way how it can be improved. A few real applications of this concept are listed, detailing experiences obtained from practice.

Jan 1, 2007

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry not only as a tool to improve the efficiency of its processes and to reduce costs but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios, such as lower ore grades, extreme weather conditions, deeper deposits, harder rock mass and high-stress environments.  

By L. R. MURPHY

This paper gives a general description of mining operations at the Rosebery Mine and a brief account of the older Hercules Mine. The more unusual aspects of the operations, such as the sinking of the inclined shaft, blast-hole experiments, diamond drilling practice, and proposed future developments are described in detail.The following main heads are used:Roseberry- General production Data.General Description of Ore-body, and Characteristics of Ore and Country Rock.Layout of MineMining Methods, Filling, etc.Blast Hole Stoping.Sinking Main Inclined Shaft.Mining Timber. Contract System.Diamond Drilling and Sampling.Surveying.Labour Force.New Developments, Sand Filling and Pumping.Hercules-Situation of Mine.Transport-Haulage and Aerial.Ore Bodies.Stoping Methods.Ore Handling.

Jan 1, 1949

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By SAHENDRA SINGH, SANJIT KUMAR PAL, DHARMITA HORO

This study was carried out in Ichadih to map the sulfide/gold mineralization using combined electrical resistivity tomography (ERT) and self-potential (SP) methods. No geophysical analysis has been carried out to delineate such ore deposits in the area. Thus, the study provides a different approach for approximate location and extension of the quartz reef associated with sulfide/gold mineralization. It also provides the elementary idea for further detailed subsurface investigation in terms of geological and geophysical approach. 

By O. A. Bascur

In recent years, metal-producing companies have increased their investment in automation and technological innovation, embracing new opportunities to enable transformational change. Transformation to a digital plant can fundamentally revolutionize how industrial complexes operate. The abundant and growing quantity of real-time data and events collected in the grinding and flotation circuits in a mineral processing plant can be used to solve operational issues and optimize plant performance. A grade recovery model is used to identify the best operating conditions in real time. The strategy for increasing the value of instrumentation in current plants is reviewed. An optimal Gaudin size distribution model provides augmented information from traditional sensors to find the optimal grind cut size to reduce metal losses in the flotation circuits. Sensors in flotation circuits enable an estimate of the recovery and determination of the optimal froth depth and aeration using an air hold up flotation model. A strategy of classifying data for on-line generation of insights to using operational intelligence tools is described. The implementation of a recovery/grind strategy with industrial examples in non-ferrous mineral processing is presented.

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.