Search Documents

By G. Zain, Abdel-Zaher M. A. Abouzeid, Y. S. Mustafa, A. A. S. Seifelnassr

The main forces acting on minerals in conventional size reduction units are compression, impact, attrition, and/or abrasion. Usually a combination of these forces shares the breakage action of the minerals with one or more of these forces dominating the breaking action, depending on the machine used. The present work concentrates on the behavior of quartz when stressed with compression force in a confined piston die. Several size fractions within the size range minus 10 mm to plus 0.85 mm were compressed in the piston die. The measured parameters are compression load, bed thickness, displacement as a result of compression, rate of displacement, and the size distribution of the products. It was found that the size distributions are, to some extent, different from those produced by the ball mill or the high-pressure roll mill. This is mainly because of the differences in the type of the acting forces in each case. It was also found that the cumulative weight of the distributions is reasonably normalizable with respect to the median particle size of the product. The specific energy expended is inversely proportional to the median size of the products, and the reduction ratios, xf/xp, are directly proportional to the applied compression force, and hence, to the specific energy expended. A simple model is suggested for predicting the particle size distribution as a function of the expended energy. The calculated values of the size distributions match fairly well with the experimental values, except at the very low energy levels, where most of the energy expended is consumed in the rearrangement and packing of the particles in the confined space with little or no breakage.

By Revy T

A testwork program aimed to improve the assaying of underground face samples established that for an Accelerated Cyanidation Extraction using the LeachWELLTM 60X catalyst, followed by an Aqua Regia finish (to quantify non-cyanide-extractable gold): ò Assay results (including the aqua regia finish) from a full set of samples from one underground face can be returned within four hours. ò The reagent dose to make the method simple and 'bullet-proof' is 8 gm LeachWELLTM 60X and 20 gm NaCN per 200 gm sample (30 per cent solids). Pulverising is to 90 per cent passing 75 micron (compared to the standard of 90 per cent passing 150 micron), and cyanidation is completed within one hour - however both might be further optimised. ò The LeachWELLTM/Aqua Regia results demonstrate that Fire Assays suffer from a significant nugget effect which makes the Fire Assay data relatively unreliable. ò Original costs, specific to Bannockburn (viz including an Aqua Regia finish), handling approximately 20 000 to 25 000 per annum is estimated to be $5.40, ie about one-third less than fire assaying. Optimising is further reducing these costs. It is estimated that the LeachWELLT"'/Aqua Regia assay procedure has reduced the probable error limits of any given assay of this ore from the range 0.74x to 1.36x for Fire Assay, to an appreciably smaller range of 0.90x to 1.11x. Thus for a cut-off grade of 1.60 g Au/t, samples with Fire Assays ranging up to 2.18 g Au/t have 25 per cent chance of being below cut-off, while samples with Fire Assays as low as 1.18 g Au/t have an equal chance of actually exceeding cut-off grade. This 1 g Au/t range in uncertainty is generally unacceptable for many practicalgrade/tonnage relationships. By contrast, using LeachWELLTM + Aqua Regia assays, the estimated corresponding limits are 1.44 g Au/t and 1.78 g Auk respectively - a far more tolerable 0.34 g Au/t range of uncertainty. Subsequent data has demonstrated that sufficient accuracy for grade control is achieved by Accelerated Cyanidation alone, further halving the cost of assays.

Jan 1, 1994

By S Russell

The completion of the $1.1 B Cape Lambert Upgrade project is the second ‘pillar’ in Rio Tinto Iron Ore’s expansion program that has enabled Rio Tinto Iron Ore to effectively double iron ore shipping capacity from the Pilbara between 2003 and 2009 to 220 million tonnes per annum (Mt/a), following the successful completion of the Dampier Port upgrade project two years earlier.The Cape Lambert Upgrade has built on and enhanced many of the engineering achievements of the Dampier Port upgrade project, as well as developing innovative and unique engineering solutions for this complex ‘brownfields’ project that presented its own challenges, particularly in this distinctive open-water port environment.The project was implemented in two phases to achieve an increase in port shipping capacity from 55 to 80 Mt/a – an enhancement phase and an expansion phase.The initial enhancement phase, which provided an increase to shipping capacity from 55 to 60 Mt/a, focused on increasing the utilisation and effi ciency of existing plant and equipment with a relatively small capital expenditure.The expansion phase, which provided the increase in shipping capacity to 80 Mt/a, included extending the existing iron ore wharf by 256 m to create four shipping berths, a new shiploader, an expanded stockyard (including a new fourth bucket wheel reclaimer) and a new surge bin facility to maximise outloading tonnage rates.The Cape Lambert Upgrade project was implemented whilst the port remained fully operational and continued to ship record tonnages of iron ore throughout the project duration. This achievement required signifi cant upfront planning and sequencing of construction activities to support the operation of the port. Innovative design and construction techniques were used to mitigate the impact and enable construction activities in and around the operating plant.Throughout the project, new benchmarks in engineering design and construction practices were established, which have since been adopted for new iron ore port facilities currently in planning phases.

Jul 11, 2011

By L E. Howard

Micro-computed tomography (Micro-CT) is an X-ray imaging technique that produces high-resolution 3D computerised ‘virtual’ models of geological specimens based on the X-ray attenuation of different materials in the specimen. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels, each assigned a gray value based on X-ray absorption. Micro-CT has enormous potential for allowing non-destructive, digital analysis of structure and composition when the mineralogical phases can be digitally separated. However, variation in X-ray flux between scans results in highly variable grayscale values for identical materials. Consequently, materials usually have to be segmented manually, which is subjective, inaccurate, labour-intensive and time consuming. Here we present a protocol and imaging software package that can be used to accurately and precisely extract quantifiable information in a repeatable and objective fashion. The software will allow the separation, visualisation, measurement and analysis of spatial and volumetric distribution of different mineral phases without damaging the specimen. This paper explains the potential use of this protocol and software package to ultimately allow automatic segmentation and quantification of gold in drill core samples, removing subjectivity and inaccuracies from data processing.

Sep 5, 2011

By T Honeyands

At present we are witnessing large investments in the iron ore industry, fuelled by demand from Asia. At the same time, there is a changing landscape in pricing of iron ores, with the recent demise of the benchmark system and the evolution of market based index pricing systems. From a customer perspective, it is the behaviour of iron ores in downstream processing that gives them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions, and in setting quality price differentials.This paper describes the use of the Marx value in use (VIU) model to quantify the downstream value of iron ores. The Marx model consists of heat and mass balance modules for sintering, pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples given for the relative value of haematite, Marra Mamba, and channel iron deposit (CID) ores.

Jul 11, 2011

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

By C F. Stokes

The Trident Gold Deposit has been successfully developed by Alacer Gold (formerly Avoca Resources Limited) into a 1.3 Mt/a operation in the space of four years from discovery to first gold pour (2008). The current in situ Resource for Trident is estimated to be 5 900 000 t @ 5.0 g/t for 940 000 ounces at a cut-off of 1 g/t or 2 g/t depending on ore style. Production to date (Alacer and previous owners) is in excess of 500 000 ounces. The deposit lies towards the southern end of the Norseman-Wiluna Greenstone Belt in the Archaean Yilgarn Craton, where it is centred on the historical Higginsville Mining Centre, midway between the world class gold centres of St Ives (+15 Moz) and Norseman (+6.5 Moz). Trident is hosted primarily within a thick, weakly differentiated gabbro with subordinate mafic and ultramafic lithologies and comprises a series of north-northeast trending, shallowly north plunging ore zones. The deposit comprises two main mineralisation styles; large wallrock-hosted ore-zones comprising sigmoidal quartz tensional vein arrays and associated metasomatic wall rock alteration (Eastern Zone, Western Zone and Apollo) hosted exclusively within the gabbro; and thin, lode-style, nuggety laminated quartz veins (Athena and Artemis) that formed primarily at sheared lithological contacts between the various mafic and ultramafic lithologies. The initial interpretation of the Trident Deposit was based on steeply-dipping structures controlling the zones of mineralisation, with much of the targeting and drill-testing aimed at this style of orebody. Subsequent exposure of the orebodies has identified a series of shallow-east dipping mineralised systems (interpreted to be large reverse shears) that at their intersection with the steep-dipping structures cause significant gold enrichment. It is postulated that both orientations are primary fluid pathways with the intersection between the two resulting in zones with significantly high concentrations of gold mineralisation (in excess of 300 000 ounces). This new understanding on ore controls at Trident has identified that the thin lode-style shear-hosted laminated veins are continuous for over 1700 m along strike as they step en echelon down-plunge. In addition, a repetition and periodicity to the intersection between these steep dipping lode-style systems and the shallow-dipping mineralised zones (estimated to be 700 - 900 m down-plunge) has been identified which has considerably increased the down-plunge potential of the Trident Deposit.

Aug 22, 2011

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Yuting Xue, Khaled Mohamed

The failure of coal ribs is a major hazard in underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) have been working on the development of an engineering-based rib control method. A user-friendly standalone application, called Design of Rib Support (DORS), is being developed to ease the calculations of rib support. DORS can estimate the Primary Rib Support Density (PRSD, ton/ft2) for development loading. However, it still needs to take account of another key factor, bolt length, in rib support design. The bolt length can be estimated from the rib fracture depth, and this study focuses on the coal rib fracture depth analysis with numerical modeling and artificial neural network. A total of 331 FLAC3D simulations with different mining scenarios and rib conditions were conducted for this study. Machine learning was then used to predict coal rib fracture depth under different conditions. Based on the numerical simulations, the parameters for mining scenarios and rib conditions were collected as features for machine learning, and coal rib fracture depths were collected as the target to predict. Good data correlation (r-square) was obtained with the use of an artificial neural network. The

By Denise Crocce Romano Espinosa, JUNIOR AMILTON BARBOSA BOTELHO, Jorge Alberto Soares Tenorio

Bauxite ore is used to produce alumina in the Bayer process. For each tonne of alumina produced, around 1 to 1.5 t of bauxite residue is generated, with an estimated 4 Mt of the residue generated worldwide in 2015, four times more in 1985. The residue is currently stocked in tailings dams. A new step in the Bayer process has been used to recover sodium hydroxide, which is used as a leaching agent, and reduce its content in the residue. After digestion, the residue is separated from the Bayer liquor and passed through press filters. This bauxite residue is known as a source of scandium. Characterization of the residue is an important step to map opportunities worldwide. For this reason, the goal of the present study was to characterize the bauxite residue and evaluate the challenges for scandium recovery. The scandium content was found to be 43 g/t, which makes this bauxite residue attractive for extraction purposes.

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By S A. Ravishankar

In heavy minerals separation, the titanium and iron oxide phases are separated from silicates in the coarser particle size range (80 - 150 mm) using magnetic and electrostatic separators. With the ongoing challenge of heavy mineral ore deposits getting increasingly finer in particle size, conventional separation equipment suffers from the ability to process this material at the same throughput rate as coarser particles. A variety of magnetic separation technologies were developed to perform at a much finer particle size range, down to 2 mm in the clay industries mainly to remove titaniferrous oxide particles. Complementing the developments made on the physical aspects of magnetic separation, Cytec Industries has recently developed a ‘bolt-on’ chemical enhancement technology for magnetic separation (CEMS). This is to enable separation of finer particles, and weakly paramagnetic titanium phases from diamagnetic silicates that are not amenable to magnetic separation. This paper will provide an outline of the technology, illustrate its ability to process a wide variety of ores, and also discuss plant limitations. The major advantages of chemical enhancement technology to magnetic separation includes: simple dosing equipment extension to existing magnetic separation technology; ability to produce product of comparable quality with improved cost effectiveness, when compared to incumbent flotation; removal of impurity minerals over wider size range; enhanced removal of non-magnetic impurities; and improving the process robustness. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for removing impurities at lower levels in other mineral systems as well.

Oct 5, 2011

By A G. Noble

Tunnelling for hydro-electric power projects can be a very challenging component of the overall development. In contrast to urban transportation tunnelling where the logistics for access and supply of power, water and other essentials are readily available, hydropower projects are usually in very remote locations and all necessary plant, equipment, spares and materials need to be brought in and the site must function as a self sufficient unit.For a large scheme the river diversion tunnel(s) are usually on the initial phase critical path in order to meet the non-negotiable deadline of river diversion before the onset of the wet season. A newly formed tunnelling crew, once mobilised to the site for the project, will face the first major learning curve of the project’s systems and logistics during this critical tunnelling activity.Power tunnels convey the water to the turbines in the powerhouse and are usually on the critical path for the main works, especially if the scheme comprises a powerhouse located within an underground cavern. A modern cavern arrangement requires a complex warren of various openings: access adits, ventilation/cable tunnels, shafts, surge tunnels, etc.Hydropower tunnel construction tends to be dominated by tunnel boring machine (TBMs) or drill-and-blast excavation techniques and each has its challenges in very remote locations. TBMs still have long lead times as for any type of project, but additionally require a thorough roads and bridges infrastructure assessment of the country from the port of entry to the site to ensure a problem-free delivery. In some cases the project also requires the establishment of a complete precast concrete segment production facility and the space for creation of laydown areas; there is no ‘just-in-time’ delivery mechanism applicable to typical remote hydropower sites.This paper highlights the technical and risk management considerations in the planning, design and construction of tunnels for hydropower projects. It contrasts the typical factors that govern the design of urban transportation tunnels with those for remote hydropower tunnels. The perspectives of stakeholders are provided including those of international lenders. With examples from large and small scale projects across the globe it provides an insight to all parties and in particular, those tunnellers that are working in the hydropower field for the first time.

Mar 8, 2011

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By R Miller

The enrichment of magnetite to haematite and haematite-goethite leads to a coincident magnetic low and gravity high within the banded iron formation. Palaeochannel deposits of pisolitic limonite can be expected to provide a relative magnetic high and gravity low in a sinuous geometry. Detrital iron deposits of conglomerate, scree or ‘canga’ might have indistinct magnetic response but will usually have a relative gravity high.These signatures provide clear discriminators detectable by a joint gravity and magnetic survey.The combination of airborne gravity gradiometry and magnetometry is particularly powerful in detecting and discriminating targets, as well as mapping lithologies and structure, across a wide variety of iron ore deposit styles. It provides detection capabilities in a platform capable of rapid, complete coverage with minimal access issues. This approach has been used in FALCON™ airborne surveys for iron ore exploration in the Great Lakes, USA; the Middleback Ranges, South Australia; and the Hamersley Basin, Western Australia.The complex magnetic properties of iron formations (particularly remanence, anisotropy and depth of weathering) prevent this approach from being simple. The use of vector residual magnetic intensity (VRMI), calculated from the measured total magnetic intensity (TMI), assists by reducing the complexity due to the different directions of the remanent and induced magnetic fields.Estimations of the density to magnetisation ratio via the pseudo-lithology calculated from the VRMI and gravity gradients provide a useful method of capturing the discriminatory power of joint magnetic and gravity gradient data.

Jul 11, 2011

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By Laxaminarayan Holla

Significant coal reserves in New South Wales lie underneath major bodies of natural and stored surface waters. In order that mining can occur safely and without any adverse effect on the surface, various statutory provisions and administrative guidelines have been framed for regulating the surface and sub-surface strata disturbance. There are particular bases for the existing guidelines and the assumptions which were made in their choice. Evaluation of the guidelines in the light of the knowledge gained during the last ten years indicates that they are conservative in some cases and can be made less restrictive without lowering the safety standards. The suggested changes include reduced width for pillars in both bord and pillar first workings and panel and pillar workings, and increased level of extraction for a given degree of subsidence. Changes, if implemented, would lead to increased coal recovery.

Jan 1, 1987