Search Documents

By W. W. Adams

Fatal accidents at coal mines throughout the United States numbered 170 during May , 1923 , according to reports received by the Bureau of Mines of the Department of the Interior from State mine inspectors . The production of coal during the month was 54,649,000 tons ; hence , the fatality rate was 3.11 per million tons . In May last year the fatality rate was 4.22 , based upon an output of 20,636,000 tons , including 35,000 tons of anthracite . Because of the miners ' suspension of work last year, the production of fresh-mined anthracite in May 1922 was completely stopped ; in May 1923 the anthracite output was 9,573,000 tons . For bituminous mines alone , the fatality rate in May 1923 was 2.67 per million tons as compared with 4.17 in May a year ago . During the first five months of the present year , the fatality rate for bituminous mines was 3.55 per million tons , based on 809 deaths , as against a rate of 3.70 for the corresponding months last year, based on 611 deaths . The rate for 1923 represents a reduction of 4 per cent . For anthracite mines alone the five-month fatality rate for 1923 was 5.36 per million tons , based on 228 fatalities , as against a rate of 6.72 for the first five months of 1922 based on 147 fatalities . The rate for 1923 represents a reduction of 20 per cent . The average fatality rate for May during the past ten years ( 1913-1922 ) is 3.37 per million tons for bituminous coal mines and 6.02 per million tons for anthracite mines . A gas explosion , due to open light , occurred on May 6 at Aguila , Colorado , and resulted in the death of ten men . This explosion brought the number of "major disasters " in 1923 to 4 , with a loss of 145 lives . During the first five months of last year, there were 7 similar disasters with a loss of 82 lives . The year's record to date for all fatalities from all causes shows a reduction in the fatality rates per million tons from haulage accidents and from falls of roof and coal , an increase in explosions of gas and dust and in accidents due to electricity , and no change in the fatality rate from explosives . The reductions in haulage accidents and in falls of roof and coal are particularly gratifying, because these two classes of accidents usually cause about 65 per cent of all fatalities in the coal-mining industry . Reports of Investigations , Department of the Interior , Bureau of Mines .

Jun 1, 1923

By Raymond W. Hiteshue, Henry H. Ginsberg, Paul S. Lewis

Coal was gasified in the presence of up to 3.57 million roentgens of gamma rays by the Bureau of Mines to determine whether the irradiation increased the gasification rate or yields of methane and hydrogen . High volatile A bituminous coal was gasified with steam at 500 and 1,500 psig and temperatures of 1,400 ° and 1,800 ° F ; five other coals ranging in rank from lignite to anthracite were gasified at 500 psig and 1,800 ° F. The average results of replicate experiments with and without radiation were compared for possible effects of radiation from 40,000 curies of radioactive cobalt . The irradiation had no gross effect on the gasification rate or on the yield and distribution of methane and hydrogen . It was concluded that gammaray irradiation produced no improvement in the technology or economics of coal gasification .

Jan 1, 1964

By Raymond B. Ladoo

The Bureau of Mines frequently receives requests for information on the mining , preparation and marketing of epsomite or Epsom salt , and in order to answer such inquiries the following information has been compiled . While it is probable that few people have considered epsonate as a mineral product , it will be noted that it should be so regarded and its production forms an important industry .

Mar 1, 1922

By Andrew Dobson

The assessment and control of environmental noise from mines has become increasingly important in recent years, due to urbanization and population growth, increased regulation of environmental factors, and overall awareness and sensitivities to noise exposure. Minimizing adverse effects on communities and achieving compliance with local ordinances is now commonplace, and consideration of noise during the design and/or operation of a mine cannot be ignored. Ventilation equipment can represent the loudest and most bothersome equpiment at mines, however there are complexities when attempting to control the assocaited noise, due to the acoustical nature of mine vent fans. In fact, the utilization of traditional and/or industry standard methods can intensify the noise impact, or simply not work as intended. This paper provides recommendations on specific noise control methods that are suitable for mine ventilation equipment, based on recent assessment work and field experience.

Oct 1, 2024

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By Jeanie Wills, Theresa Nyabeze, Samantha Espley, Donna Beneteau

This presentation reports survey findings that aim to modernize the definition and understanding of the term 'mining.' The survey, conducted via LinkedIn in Winter 2024, garnered responses from a diverse group of individuals, including current or former employees of mining or exploration companies, mining consulting firms, service providers, supplier firms, as well as students and retirees with industry experience. The data, ethically approved by the University of Saskatchewan, offers valuable insights into satisfaction levels within the mining sector and suggests an expansion of the identifying characteristics of definitions of mining. This marks the third CIM gaining insights paper by Beneteau, Espley, and Nyabeze, following previous works on 'Career Satisfaction for Women in Mining' (2010) and 'Mentorship Initiatives in the Canadian Mining Industry' (2018*)."

Oct 1, 2024

By Muhammad Usman Siddiqui

Managing and analysing the vast amounts of data collected in a mining project effectively is crucial for enhancing the project's economic feasibility. The efficient utilization of this data is critical to minimising the time spent on projects and increasing project value. Process engineers can effectively integrate geometallurgical data into plant operations by employing analytical tools like Python, significantly optimizing the mine-to-mill process. This practical approach is a game-changer in the mining industry. Classifying a geomet dataset into units of similar characteristics (properties of the ore) is an important outcome of a geomet study. This approach simplifies data classification, allowing for class-by-class process modelling, which improves the decision-making process in mine planning and development. Classifying a geomet dataset involves using grade, lithology, and test work data (if available) to create blocks of similar characteristics, known as ‘geomet units.’ Compared to conventional methodologies, these units provide context and empirical evidence that can be more accurately mapped onto block-by-block process flowsheet development and net present value (NPV) estimation. This robust classification method reduces a project's technical risks and influences the initial mine planning sequence to maximise profitability. Defining robust geomet units with data sets with similar material is challenging due to the vast amounts of data available and the database's high heterogeneity. The methodology's purpose is to minimise time-consuming low-value-adding aspects of geometallurgy. The approach is different for a greenfield and a brownfield study, as all the valuable data in a brownfield process can be utilised to define the geomet units. Python has various libraries providing multiple machine-learning algorithms to assist in classification. The k-means algorithm is used for clustering, and the SHapley Additive exPlanations (SHAP) method is used to quantify the effect of each feature on the clustering results. However, even with automation, the methodology still requires a keen eye to account for the nuances that appear from project to project.

Oct 1, 2024

By Amir Karami, Derek Kinakin, Catherine Schmid

The Mathews Stability Graph Method (Mathews et al., 1981) has been used by geotechnical engineers and mining engineers for over 40 years to estimate the performance of longhole open stopes in underground mines. The method is widely used and accepted by practitioners because it is relatively simple to use and can be modified to account for observed performance at a given mining operation. While the simplicity of the method increases its accessibility and utilization, it does not intrinsically account for variability in the various inputs, including rockmass quality, structure, stress, or stope orientation. This paper presents a modified approach for the Stability Graph Method, whereby Python scripts are used to process available geotechnical datasets and combine them with actual or potential distributions of Q parameters, induced stress, structure, or stope orientation. The resulting Stability Numbers are then plotted as a contoured distribution on the Stability Graph.  This allows the practitioner to quickly incorporate large datasets into the analyses, while also developing an understanding of how variability in rockmass quality, induced stress, structure, or stope orientation could affect stope stability.  This paper presents the fundamental principles of the Stability Graph method, the Python script and workflow, and two case studies to demonstrate the utility of the tool.

Oct 1, 2024

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By Gurupraveen Ramanathan

Slot raises are relief holes within a stope in longhole stoping methods, designed to provide a free face that facilitates the expansion of the blasted rock during blasting, ultimately achieving the desired fragmentation. Various methods are employed to produce these slot raises, like conventional drop raise drilling, raisebore & V30 drilling. However, slot drilling is generally characterized by high costs and limitations in precision, resulting in unplanned ore losses and dilution. This paper introduces a novel alternative to slot drilling referred to as the "paste slot", designed specifically for paste backfill operations in underground mining. This new method emphasizes considerations in cured paste strength, paste wall removal, and stope dimensions and employs modified drop raises or dumped rings to optimize blast gas effectiveness and material flow. The paste slot method eliminates the need for reamers and reduces the total slot drill meters an average from 650m to only 300m for narrow stopes (3-4m wide). This significantly reduces the stope cycle time, leading to substantial cost savings and increased productivity. This new method was successfully implemented at the underground mines in Canada and Australia, resulting in a 20% reduction in stope cycle time and cost savings of 53,000 USD per slot compared to the conventional slot. This paper discusses the design and execution strategy of the paste slot method in underground paste backfill operations. It highlights the advantages of the method, shares operational insights gained during implementation, and showcases its potential applicability to other mines across Canada and globally.

Oct 1, 2024

By G R Ryan

Recent events have raised the issue of whether, and if so when and how, an explorer may gather data from a mining tenement or permit which is held under the relevant mining Act by another party. Two situations arise: that of the small operator who wishes to prospect, and if successful mark off, ground held by others by virtue of the local form of exploration permit; and that of a regional explorer who may wish to enter on to some one else's existing mining tenement within the region of interest. The legal situation varies from state to state. At present the broad consensus seems to be that, provided consent is given, small-scale prospecting on another's exploration permit is at least tolerated if not actually provided for by the relevant Act. Entry onto a granted tenement to carry out any form of exploration is, however, prohibited in all jurisdictions unless consent is given. Furthermore it would appear that the proposal and conclusion of a joint venture agreement places certain obligations upon the party proposing to carry out exploration. These conclusions apply where ground surveys are proposed. Where data acquisition is by aerial survey the situation is much less clear, principally it would appear, because up to now little thought has been given to it. If trespass applies at ground level, at what height does it cease to apply? Can aerial magnetometry or photography be classified as prospecting? Is there an obligation upon public authorities who carry out remote sensing to make data available to the holders of mining tenements within the surveyed areas? Moves are now afoot to address these and other considerations, and it would be in the interests of everyone if a national approach to the problem could be adopted from the beginning. Certain suggestions in this respect are put forward.

Jan 1, 1994

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By B. J. S. Sceresini

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentra­tion and high pressure to achieve extremely rapid gold dissolu­tion rates. This is made possible without suffering from high energy or wear rates by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device which can be constructed from a variety of wear and chemical resistant materials. High temperature tolerance is also possible so that the device can be incorporated into a pressure leach circuit with significant capital cost savings because of the high capacity to volume ratio that is an inherent feature of the device. For cyanidation applications the outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of about 150 dry tonnes per hour at 40-45 % solids. Service life at this throughput is at least three months. Six mines are currently employing the Filblast Process and another six are conducting plant trials. The ore types range from highly reactive, almost impossible to treat, pyrrhotite/ arsenopy­rite to deeply weathered clay ore which forms a highly viscous pulp. It has been found that the effect of shear thinning has resulted in improved leaching and adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately eight million tonnes per annum. This paper presents the operating benefits and cost savings which have been achieved in four plants, two treating oxide/ sulphide ore blends and two treating highly reactive sulphide ore and concentrate. Filblast leasing and maintenance charges and pump operating costs are about ten percent of the benefits. A conceptual cyanidation circuit based on the Filblast Cyanidation Process is also discussed. The Filblast System is an in-line pressure leach aerator/ reactor which generates very high shear and greatly enhances mass transfer rate by generating extremely small gas particles where oxygen gas is required for oxidation reactions and/or utilising the high shear characteristics to minimise the diffusion boundary layer. Both of these rate limiting factors effect the rate mechanism for gold cyanidation. Initially two multi-stage Filblast aerator cartridges formed a leach train but now the trend is to install a single submersible cartridge of equivalent perfor­mance. This design simplifies installation and minimises change-out times. However the in-line concept can be employed where high pressure leaching or pressure oxidation is required. The reactor is submerged in the leach tank so that the mass of gas micro-bubbles contained in the discharging slurry is entrained in the agitator vortex and is thoroughly dispersed throughout the tank. A diagrammatic representation of a leaching circuit incorpo­rating the Filblast Reactor is shown in Figure 1. The recirculation pump takes new feed directly from the cyclone overflow trash screen either under gravity or pump fed and recirculates the balance to maintain 250 - 270 m3/h total slurry flow. All of the leach feed slurry gets at least one pass through the Filblast thereby eliminating short-circuiting. Typically a 6/4 EAH Warman pump drawing 60-70 kW is required to circulate 250 m3/h through the system. The back pressure generated by the Filblast is in the range of 400-500 kPa depending upon pumping rate, pulp density and slurry rheology. The high shearing rate effectively negates the viscous effect of slurries and the addition of a gas further reduces the pulp density by virtue of the intensely aerated, homogeneous medium. The gold leaching Filblast cartridge elements are made of polyurethane but stainless steel, ni-hard, rubber or ceramics can be used depending on the operating temperature and design duty. The efficiency of the Filblast Leach Reactor in gold cyani­dation is due to the extremely efficient mixing, oxygen dissolu­tion and surface polishing action of the Filblast design. Either air or oxygen may be used but Atomaer recommend the use of oxygen because of the rate benefits gained from cyaniding at [02] significantly > 20 ppm D O in the reactor. Very high DO concentrations have been measured; in excess of 50 ppm. There is some debate as to whether the value is a true measure of the DO or the oxygen meter sensor is measuring the effect of a mass of very fine bubbles of free oxygen. Regardless of the fact the reactor has registered some amazing gold dissolution rates commonly in excess of 80 % during transit of the pulp through the reactor. The elapsed time is less than half a second!

Jan 1, 1995

By Bruno Sceresini

The Filblast Cyanidation Process incorporating intense high shear mixing, high gas mass transfer efficiency and high oxygen concentrations under conditions of elevated pressure has now been been successfully applied in gold cyanidation mills since May 1993. The first commercial unit had a slurry capacity of 110 cubic metres per hour. Since then 230 and 450 cubic metre per hour units have been installed and a 1,000 cubic metre per hour unit has been designed. Laboratory and pilot plant Filblasts have also been built. The reactor is a robust, compact in-line or end-of-line device and may be constructed out of a wide range of materials including wear and corrosion resistant alloys and ceramics. The Filblast Process may be applied to high temperature leaching of refractory gold ores and base metal concentrates. The development and application of the Filblast Gas Shear Reactor as a cyanidation tool has removed the constraints of plant size in cyanidation applications in mobile or readily transportable gold plants. A 250,000 tonne per annum fully modularised gold ore treatment plant with the Filblast and AARL Pump Cell as core technologies is nearing completion. This plant includes several novel features which are predicted to achieve widespread adaptation in modem cyanidation plants. This paper presents a briefreview of the development of the technology and the principles incorporated in the Filblast system. A number of case studies are presented which show significant financial benefits due to more efficient reagent utilisation, higher recovery and increased through-put.

Jan 1, 1997

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011

By U König

The use of high speed detectors made X-ray diffraction (XRD) an important tool for quality and process control in the mining industries. Besides knowledge about the mineralogy of a sample it provides useful information in terms of quantification of the crystalline phases and the amorphous content. Cluster analysis of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. The studies of this paper demonstrate how XRD and data clustering can be used for grade control, process optimisation and quality control of iron ores and iron ore sinters. These new developments have an enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron and sinter materials implemented in an industrial environment.

Jul 11, 2011

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011