Search Documents

By Ivan F. Avery

DOMEST1C production of carbon black in 1963, remained at about the same level as in 1962. Carbon black produced by the furnace process increased 2 percent to 1,880 million pounds in 1963 and accounted for 91 percent of the total output. Channel black production continued to decline and was 14 percent less than a year ago. Shipments during 1963 totaled 2,098 million pounds, a 1 percent increase for the year. An increase of 88 million pounds in domestic sales was partially offset by a decrease of 72 million pounds in carbon black exports. Total value of carbon black production in 1963 was $148 million. The average value per pound was 7.18 cents or 0.12 cent per pound more than in 1962.

Jan 1, 1964

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. II. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under-signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1934

July 1-Sept. 30, Centennial of Engineering, Chicago. Aug. 28-29, Oak Ridge Summer Symposium, Oak Ridge, Tenn. Sept. 3-8, AIME, Industrial Minerals Div., annual fall regional meeting, Chicago. Sept. 3-6, AIME, fall meeting, Palmer House, Chicago. Sept. 3-13, AIME, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-6, Engineers' Council for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 10-12, Porcelain Enamel Institute, annual shop forum, University of Illinois, Palmer House, Chicago. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, ill. Sept. 18, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver.

Jan 1, 1952

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Paul M. Ambrose

Overall the domestic abrasives industry had one of its best years in 1965. Production and value of all commodities increased over that of 1964 which also was a good year. Production of tripoli that was down in the previous year rebounded and production from two new mines was reported. Plant capacities for production of silicon carbide and fused crude aluminum oxide and production from plants in the United States and Canada increased, but demand was high and yearend stocks were less than at the end of 1964. Foreign Trade.-Increases in value of most imports of abrasive materials in 1965 were offset by a decrease in the value of imported industrial diamond. Production of fused aluminum oxide and silicon car-bide in the United States and Canada and imports of these commodities into the United States increased, but combined exports of finished grain of these materials was virtually unchanged from the previous year.

Jan 1, 1966

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

By David Bendersky

The principal objectives of this study are to: (1) survey electrical practices in metal and non-metal mines, (2) survey electrical practices in metal and non-metal mills, (3) clarify the federal regulations governing electrical practices in metal and non-metal mines/mills, (4) analyze electrical accidents, and (5) make recommendations aimed at improvement of the safety of electrical practices in metal and non-metal mines. Information was obtained from literature searches, accident reports, visits to 27 mines and 12 mills, and discussions with knowledgeable industry and government people. The various electrical power systems and practices at the mines and mills visited are described. Similarities and differences based on the type of mining and the minerals being mined or milled are presented. The federal regulations governing metal/non-metal mine/mill electrical practices (Code of Federal Regulations, Title 30, Sections 55.12, 56.12, and 57.12) are presented and discussed. Explanations of each regulation are provided in an appendix. The attitudes of mine/mill operators towards the federal regulations are described. An analysis of the electrical accidents in metal/non-metal mines and mills during the period 1972-1978 is presented. Recommendations, including specific research and development activities, aimed at improvement of electrical safety in metal/non-metal mines are submitted.

Jan 1, 1980

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By E. K. Stanek

This report contains the results of several related research efforts, all of which were aimed at enhancement of mine power system safety and reliability. The largest single effort was on optimum spares and maintenance scheduling for various components of a mine power system. Two closely related tasks involved calculation of the minimum arcing faults that could occur on dc trailing cables and the use of trippable load break switches to clear ground faults. Both of these tasks are concerned with reliable fault clearing to prevent shock and fire hazards. Three other closely related tasks were concerned with aspects of mine power system design: (1) alternate network topologies, (2) optimum voltage selection for mine power systems, and (3) selection of system components. The other research task consisted of laboratory tests to ascertain the effects of repetitive, low-level transients on insulation systems.

Jan 1, 1979

By Tim Hughes, Steve Gannon, Jennifer Abols

"In the past year, two very innovative gold ore processing plants have been designed, built and commissioned by Gekko Systems Pty Ltd. The first plant in Vietnam utilizes conventional crushing and ball milling followed by gravity concentration (Inline Pressure Jig (IPJ) and Falcon concentrator), flotation, intensive leaching (GFIL), the first industrial scale use of AuRIX®1001 ion exchange resin and a cyanide destruction circuit. The second plant, in Australia, uses a 3 stage crushing circuit to crush the gold ore to minus 1mm, followed by gravity concentration utilising a rougher, scavenger, cleaner circuit of IPJ’s and a Falcon concentrator. A direct smeltable gold concentrate is produced as well as a lower grade concentrate for future intensive leaching or sale. Both plants were designed and built within very tight time frames and budgetary constraints. The experience gained during the plants’ design, commissioning and operation are discussed.INTRODUCTIONGekko Systems (Gekko) is a leader in the development of innovative technology for gravity recovery and intensive cyanidation. It provides low cost and metallurgically optimal solutions for its customers. It has also led the trend away from whole ore cyanidation (CIP/CIL) towards gravity/intensive cyanidation (GIL) and gravity/flotation/intensive cyanidation (GFIL) plants. These types of plants offer low capital costs, low environmental impact and maximum return to investors (Rob J Longley et al, 2002). Key to this type of flowsheet is the application of a continuous concentrate unit, such as the InLine Pressure Jig (IPJ), which is designed to produce high gold gravity recoveries at a coarse grind (Sandy Gray, 2003). When combined with other gravity devices, and/or flotation, and intensive cyanidation, using the Gekko InLine Leach Reactor (ILR), very high overall recoveries can be achieved.In 2004, Gekko launched a new range of products called Gekko Modular Systems. The idea was to provide off the shelf, complete solutions for the separation and recovery of complex and free gold as well as the pre-concentration of diamonds. A series of modules were designed that incorporated Gekko manufactured as well as outsourced equipment. Gekko now offers modules ranging from feeding and conveying to crushing, gravity recovery, flotation, intensive cyanidation, refining and detox (see Figure 1)."

Jan 1, 2007

Jan 1, 1938

Jan 1, 1930

By R. V. Ramani, R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent. From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.

Jan 1, 1992

By A J. Jonaitis

The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar» filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product. Lab and pilot testwork conducted in Australia on coal fines (55-70\ -35 micron (400 mesh)) have shown that total moisture contents of less than 20\ are consistently achieved in the final cake products from the Tube Press. Currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 Series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50\ to achieve these results.

Jan 1, 1993

By D. C. Fuller

CoaLiquid, Inc. (CLI) has been in the coal- oil-mixture (COM) business for over five (5) years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August of 1979. For over two (2) years CLI has been expanding its efforts and conducting large scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit. CoaLiquid has conducted commercial scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.

Jan 1, 1982

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA), San Bernardino County, California During field work, BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1,188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) full access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion, $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrousmetal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry. MAGNITUDE OF THE BRASS INDUSTRY. According to the Thirteenth Census, in 1909 there were in the United States 1,021 fu-ms that dealt mainly in brass and bronze. This total included jobbing foundries, manufacturing plants that both cast and machine a brass or bronze product, and rolling mills, but did not include iron foundries having nonferrous departments nor the numerous large brass-foundry departments of manufacturing plants that produce the castings used in the manufacture of electrical apparatus, cash registers, pumps, and the thousands of machines that require brass castings for their construction. Penton's Foundry List for 1910 gives about 1,150 exclusively nonferrous foundries and about 2,300 iron or steel foundries that also melt brass. If the rolling mills and. jobbing foundries in manufacturing plants be included, and if due credit be given to the rapid growth of the industry in the last few years, largely through the stimulation of the automobile busi¬ness, it is probable that not less than 3,600 plants are to-day melting brass or bronze.

Jan 1, 1916