Search Documents

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By SME SME

NORTH AMERICAN TUNNELING 2024 PROCEEDINGS

Jun 23, 2024

By T. E. Swigart, C. E. Beecher

The Federal Government, as the largest lessor of oil and gas lands in the United States, is vitally interested in the conservation of those resources. This manual has been prepared at the direction of the Secretary of the Interior to call the attention of lessees of public oil and gas lands to the most common oil and gas field wastes and the best methods of preventing them; to outline the policies of the Interior Department on field operations; and to give information as to how the "Operating Regulations" of the department will be interpreted by the Bureau of Mines. The oil industry has progressed steadily. Present operating methods are much more efficient-and less wasteful-than those of a few years ago; moreover, the art of producing oil and gas is continually advancing. Public interest requires that improved methods, which will result in obtaining the greatest possible amounts of oil and gas from the natural deposits, shall be developed and used. Part I of this manual points out types of oil and gas wastes and suggests, in detail or by reference, the most practical and effective methods in current practice for stopping these wastes. Throughout Part I the department's operating policy is given, with interpretations of the "Operating Regulations" for enforcing every practical measure of conservation. Part II comprises the revised "Operating Regula-tions" which supersede all previous regulations and will govern future operations on public lands; it will be found in the pocket in the back cover of this bulletin.

Jan 1, 1923

By E. J. Babcock, W. W. Odell

The Bureau of Mines since its establishment has always taken an active interest in the utilization of lignite and in the development of the lignite dep'osits of the United States. Extensive lignite fields occur in the west central States, notably in North Dakota, Montana, Wyoming, Colorado, and Texas; there are smaller areas in several other States, some of which are widely separated. The total area of the deposits and the total amount of lignite in these several districts are so enormous that the economic value is seldom recognized. To the people of ·the west and west central regions, however, the larger utilization of lignite, in whatever form it may be, is of fundamental importance, and any new methods or uses that promise to open these great lignite fields for more general and more efficient use deserve careful study. Although these lignite deposits underlie areas of thousands of square miles, their development and general utilization has been rather slow. This is no doubt partly because many of the districts are not thickly settled or highly developed in manufacturing industries, but is largely because lignites, from their peculiar physical and chemical characteristics, are low-grade fuels. Most of the lignites in these areas are imperfectly developed coals; many have a more or less woody structure; some belong to the brown-coal type; and others are darker, denser, and more homogeneous, approaching subbituminous coal. The people living in the regions in which these vast deposits occur, especially in the west central part of the United States, are vitally interested in every effort toward bettering lignite as fuel and aiding its wider utilization.

Jan 1, 1923

By Oliver Bowles

Under a cooperative agreement between the Bureau of Mines, the United States Geological Survey, and the United States Bureau of Standards, a study of the stone-quarrying industries of the country was begun in 1914. The results of investigations made have been published from time to time.1 During the World War the Bureau of Mines centered its attention on problems relating to national defense, and detailed studies of stone-quarry problems were not undertaken except for an investigation of labor saving at limestone quarries, reported in Technical Paper 203, which related to a question of military importance. Since the return of peace, the high cost of materials and labor has made more imperative than in prewar times the conduct of investigations for aiding the quarrying industries in every way possible to adopt more economical methods and to utilize the most efficient labor-saving equipment. The publications already issued have had a wide demand, and in the interest of the quarry industries the bureau proposes to issue additions to the series as rapidly as funds are available. In an endeavor to promote economy and the reduction of waste in the slate industry, a study of slate quarrying was begun in 1920 and covered a period of about two years. Sixty-five active quarries were visited, and a detailed study made of all problems bearing on their successful operation. Field study was supplemented by a study of all information available in books or published articles on slate quarrying.

Jan 1, 1922

By Martin J. Gavin

The results of investigations of the oil-shale resources of the United States were first published by the United States Geological Survey in 1915.1 Other reports 2 have followed. These reports, investigations by private individuals and corporations, and the beginning of the development of an oil-shale industry in this country have aroused considerable interest in the possibilities of these shales as a commercial source of hydrocarbon oils. The Bu- . reau of Mines bas appreciated these possibilities, and since 1916 one or more of its engineers have given all or part of their time to investigations relating to the treatment of oil shales. A short pamphlet a containing general information on the possibilities of oil shale in this country, particularly the shales of the Rocky Mountain district, has already been published. This pamphlet gives methods for assaying the shales of oil and ammonia and contains a bibliography for the use of those desiring to search the literature.

Jan 1, 1924

By R. Van A. Mills

Rapid deterioration and destruction of metal equipment in oil and gas fields cause waste of resources and financial losses that must be lessened or eliminated if operations in many important fields are to continue profitable. The magnitude of this destruction is proved by the huge consumption of iron and steel pipe, tubing, casing, pump valves, and sucker rods to replace worn-out equipment, and by the amount of such equipment that is left in wells or junked. (See PI. I, A and B, and PI. II, A and B, and Fig. 14, p. 61.) This destruction of equipment constitu~es in itself a serious waste, but contingent production troubles, such as underground leakage of oil through defective tubing and pumps, and the consequent loss of oil and gas because of damage to pay sands by infiltrating water and silt, frequent and costly repairs with necessary suspension of production, and the ultimate injury to or loss of valuable wells, often cancel all operating profits. Many of these troubles result from rapid destruction of metal equipment by corrosive waters. The strata penetrated by the wells usually contain saline waters. Certain types of these waters, with their associated gases, are intensely corrosive; they attack well casing or tubing so vigorously as to riddle it with holes, rendering it useless in a few years or even a few months or weeks after it is installed. Pump plungers, working barrels, balls and seats of valves, and screen pipe, as well as lead lines and other surface equipment, are ruined with equal rapidity. The development and application of practical methods to retard or prevent this corrosion are among the most urgent problems of the oil and gas industry. Although much progress has been made in preventing the corrosion of metals, the need for reducing the damage from corrosion in oil and gas fields is still imperative. This is especially true of underground corrosion in the wells, because underground conditions favor corrosion and are difficult to study; hence they have not been thoroughly understood. In efforts to stop ~amage to oil and gas field equipment by corrosion, numerous methods have been proposed or tried with varying success. Some of these methods are cheap and effective. However, it is surprising that in many important fields the damage by corrosion is accepted as necessary or unavoidable, although cheap and effective methods that have been developed and successfully tried elsewhere might greatly reduce the trouble or eliminate it. This bulletin describes common causes and effects of oil and gas field corrosion and outlines methods of abating the damage. In order to accomplish this purpose best, the writer has avoided taking sides in controversies between the advocates of different metals for oil-field use; instead he describes the methods of combating corrosion in the various fields and suggests experiments that may yield valuable results. Throughout the paper he has freely used information from published reports of other investigators.

Jan 1, 1925

By Brendan Howard

Rio Tinto has a large globally distributed technical workforce and needs to ensure these employees have the requisite skills to not only manage technical risk and enable safe efficient production, but also ensure they are keeping pace with a fast-changing technological landscape. Traditional approaches to learning struggle for scale and an inability to respond to the extreme diversity of capability development needs. In response, Rio Tinto has successfully introduced innovative approaches to learning and employee engagement via leveraging the power of globally distributed networks for peer-to-peer knowledge transfer and providing mechanisms to recognise, reward and retain the individual technical contributors.

Feb 1, 2024

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By S. Mudau, P. Mohasoa, M. J. Cole

Derelict and ownerless (D&O) mines in South Africa have been an ongoing concern for over a decade. While some progress has been made to rehabilitate D&O asbestos sites, significant work remains, exacerbated by the growth in illegal mining. There are concerns regarding the accuracy and transparency of the D&O database, lack of oversight, and constrained funding, and the government is increasingly looking to the private sector to fund rehabilitation. Given these challenges, a new, sustainable approach to D&O sites in South Africa is needed to bring clarity and transparency to the process, recognise responsibilities and promote partnerships, and explore economic opportunities at D&O sites to reduce the financial liability and respond to the growing demand for critical minerals. This article has three components: i) reviews of international D&O good practices; ii) it analyses South Africa’s current approach and the D&O sites; and iii) proposes a D&O framework that addresses data, risk ratings, responsibilities and rehabilitation, economic opportunities, and stakeholder engagement. The study finds that the majority of the 6,100 so-called abandoned D&O mines are quarries and mine site features, 16% are operational, at least 11% have owners, and only 752 (12%) require rehabilitation. The framework aims to bring clarity and fairness to decision-making and to assign risk and responsibility for rehabilitation and seeks to incorporate economic opportunities to reduce the financial burden of rehabilitation, create jobs for local communities, and respond to the growing demand for critical minerals for the clean energy transition.

Apr 25, 2025

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By Paul Culvenor, Brad Gyngell

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organizations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyze the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Feb 1, 2025

By Ron Derrick

SX operators have conducted extensive shut-downs and repairs over the years to mitigate solution leaks from failed stainless steel false floors and walls in rectangular mixersettler mix boxes. Hydrodynamic modeling using first principles and constitutive equations of fluid mechanics can inform an efficient structural redesign sufficient to eliminate the plate failures. Updated mix boxes have been performing without failure for over a decade. Given the extensive construction of the original Holmes and Narver mixer-settler design throughout the world that includes stainless steel lined rectangular primary and auxiliary mix boxes, SX operators may benefit from the approach, eliminating costly shutdowns, leaks to containment, and hazardous repairs.

Feb 1, 2024

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

By Wei Zhang, Jinhong Zhang

An atomic force microscopy (AFM) image analysis has been applied to study in situ the adsorption of hydroxamic acid collector, i.e., octanohydroxamic acid (OHA), on malachite in aqueous solutions. AFM images show that hydroxamic acid collector adsorbs strongly on malachite mainly in the form of insoluble copper hydroxamate complex. Increasing the collectors’ concentration and the adsorption time both increase the adsorption of hydroxamic collectors on malachite. Results from the attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that the collector adsorbs strongly onto malachite, with strong absorbance spectra being detected, and the ATR-FTIR results confirm those as obtained by AFM. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of malachite. The findings of present study also show that AFM image analysis is a powerful tool for the study of the hydroxamic acid collectors’ adsorption on malachite surface and it can help with the development of novel collectors for malachite flotation.

Feb 1, 2025

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By Kadri Dagdelen, Steven Hoerger

For gold mines, orebody uncertainty is one of the leading causes of differences between planned and actual production. Geostatistical conditional simulations create multiple equally probable orebody block model realizations which are conditional to the current drilling information and demonstrate the sampled grade distributions and spatial statistics. These simulated block models are key inputs for a stochastic evaluation to show the likely range of grades and cash flows to be delivered by a mine plan. The stochastic evaluation outputs can be used to compare different mine plans in terms of expected values and risks to planned grades, production, costs, Net Present Value (NPV) and other plan metrics. For the McLaughlin gold mine, risk profiles are demonstrated to show how different mine, cut-off and stockpile strategies can reduce risk and improve expected value. The strategies considered were effective in improving expected NPV and reducing or eliminating tonnage uncertainty, but the strategies had little impact on reducing the uncertainty of NPV’s or mill grades. The stochastic evaluation process is also used to compare the risk impact of orebody uncertainty against the risk of not achieving planned mining tonnages or vertical advance rates. Risks for plans created with and without stochastic mine plan optimization are also compared.

Feb 1, 2025

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

Mining operations adopt a variety of measures to combat dust underground. These include ventilation systems, water sprays, physical barriers, and personal protective equipment (PPE). Respirators are a class of PPE that can provide clean particulate- free air to the users. Powered Air-Purifying Respirators (PAPRs), used commonly in medical and other sectors, are not prevalent in the mining industry. PAPRs use P100 filters that have 99.97% dust capture efficiency. We present our results from computational fluid dynamics (CFD) simulations performed to understand the impact of a PAPR on airflow and dust particle concentration in the vicinity of a miner. These results show that donning PAPRs can lower the miners’ exposure to respirable coal dust in their workplace.

Feb 1, 2025