Search Documents

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter's rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it 'is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By Jerry A. Steding

How many times have you heard "You can't drive piles because of the vibration."? You hear these words come out of the mouths of owners, engineers, and contractors. When a piling contractor hears this, he can almost always do a psychological profile of the individual uttering these words of wisdom. If the owner makes the statement, we know the odds are about 95% that the owner owns the building next door or he wouldn't care what happens to it; or the guy next door has threatened to sue the owner if he even so much as walks across the site of the proposed new building. If the owner owns the building next door to the new construction you can also be just as certain the old structure has undergone settlement. If the statement comes from the mouth of the contractor, it is usually just a case of him being inexperienced.

Jan 1, 1988

By T. D. Dreger

In the spring of 2009, Suncor Energy Inc. technical personnel saw an opportunity to improve planning and mining of overburden material in order to address aggressive construction goals and increased mining complexity. By tying together current and historical equipment performance, geological model information, and material observation in the field new operating elevations for the shovels were developed. At the same time, methodology of recording and reporting overburden movement through the Modular Mining DISPATCH system was changed. The result of this first stage of improvements was an increase in construction-grade material available at the face. The personnel involved realized that other opportunities were available to build on the initial successes and establish processes that would stand up to attrition and experience levels. A cross-functional technical team was assembled to identify ways of further improving workflows around overburden mining. Some of the opportunities realized include greater alignment between planning, reporting and operations as well as development of reporting tools that help steward Mine Operations to the plan. All of which have resulted in Suncor meeting or beating its forecast overburden targets. The cross-functional technical team continues to seek out new and better ways of doing business so Suncor can continue to deliver on its commitment of outstanding performance and results.

Jan 1, 2012

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA's Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta's central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta's showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979

By Ted Schwinden

It's my pleasure to welcome the Rocky Mountain Coal Institute to Montana. Now that you've ended a 74 year history of meeting outside our borders, I hope you'll be back more often. Even if I can't convince you to come back before 2060, when another 74 years will be up, I'm confident the Kalispell and Flathead Lake area will do the persuading for me. In recent weeks, I've made a number of speeches around the state pointing out just how wrong the revenue projections in Montana's state government made in April of '85 were when we came to April of '86. Since the middle of this month, Montana's legislators have been in Helena struggling to balance a state budget that, by the end of fiscal year '87, threatened to be some $88 million in the red. Other western states reliant on natural resource and agricultural economies have found themselves caught in the same deflationary spiral. The "window of opportunity" I proposed and the 1985 Montana Legislature passed, couldn't have been opened at a more difficult time. What was envisioned as an incentive to expand Montana's coal production, and our tax base, ran aground on low oil prices and excess hydroelectric power. De- spite the one-third severance tax rebate offered on new coal production, year-to-date figures published in the June 2nd Coal Week show that production in Montana is down almost 10 per- cent from last year. Again, we're not alone. Production in Wyoming is down 8 percent and in North Dakota, it has dropped 13 percent. An over- all 3 percent production decline in western states looks even worse when contrasted against a 12 percent increase for your eastern competitors. Montana's "window of opportunity" had the potential to be a significant signal to your industry. That potential was quickly tempered by the inability of Arab nations to stabilize world energy prices. If any of us had forgotten, the last twelve months have reminded western states that the well-being of our natural resource economies has a tremendous impact on the ability of all levels of government to provide services. The past year has also driven home that in the world of business and in the business of the world, risk-taking is still the name of the game. The Western Governors recognize the problems facing this industry - and our states - and we're prepared to fight for the future of western coal. In the past two decades, legitimate environmental concerns have created a vast body of new legislation affecting coal producers. The industry has been required to meet new reclamation standards - tough regulations relating to ground water, air quality and wildlife habitat. To the industry's credit, coal companies have hired professionals with the technical know-how to do it right. Rather than considering reclamation laws to be an unreasonable burden, today's coal company is more likely to view its reclamation efforts as a source of corporate pride. In a sense, the industry and the agencies which regulate it have matured together . . . although at times OSM is reluctant to admit that either of us capable of or willing to play by the rules. Certainly some abuses exist and OSM's oversight has been helpful in ensuring parity between those states willing to comply and those that would rather defy federal law. Nonetheless, penalizing the more modem and responsible western coal industry for abuses that occur elsewhere is both unfair and counterproductive. Federal penalties range from "cruel and unusual" reporting requirements to the proposed electricity tax that would effectively force utilities and ratepayers who have already met the sulphur emission standards to subsidize those who have dodged their cleanup responsibilities. As a member of the Alliance for Acid Rain Control, I have joined corporate leaders, academicians, environmental representa-

Jan 1, 1986

By B. C. Litzinger

Minerações Brasileiras Reunidas S.A. - MBR is a brazilian iron ore mining company geared for the export market. It is controlled by Companhia Auxiliar de Empresas de Minerações - CAEMI through its subsidiary Empreendimentos Brasi leiros de Minerações - EBM which holds 51% in MBR and is formed by CAEMI, the six major japanese steelmills and five japanese trading companies, Universe Tankships, Inc., and Indústria e Comércio de Minérios S.A. - ICOMI. The remaining 49% of MBR's capital are held by St. John del Rey Mining Company, a subsidiary of The Hanna Mining Company. MBR iron ore reserves exceed 1.5 billion tons of high grade ore distributed in 36 deposits located in the so-called IRON QUADRANGLE in the State of Minas Gerais. The Aguas Claras Mine is the largest presently known and highest grade deposit owned by MBR. Other mines such as Pico, Mutuca and Jangada are in operation at a combined rate of production of about 2 to 2. 5 million tons per year. The project consists of mine, railroad and marine terminal (slide). The Aguas Claras deposit, which is located about six kilometers southeast of Belo Horizonte the Capital of Minas Gerais, was selected for initial development. The Sistema Regional Centro of the Rede Ferroviária Federal, through its 6th Division known as the "Central " is responsible for the transportation of MBR ore, and provided the necessary railway construction to connect Mine and Terminal. The Terminal is located on Guaiba Island near the entrance to Sepetiba Bay, at about 120 kilometers west of Rio de Janeiro.

Jan 1, 1974

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the key parameters influencing the gold recovery. The model was used to direct modifications to plant operating practice. The cyanide dosing strategy was changed to reduce preg-rob gold masses and cut reagent consumption A finer grind was achieved without capital investment. The density in CIL was lowered, and tighter control was exercised over plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz, and concomitant reagent cost savings of $55,000/month.

Jan 1, 1999

By Eugene Guccione

"All engineering societies should encourage and motivate their members to take part in public affairs. And engineers, in turn, should learn to translate their technical knowledge in a language which politicians can understand," stated James Boyd last month as he received the Hoover Medal, which is awarded annually by four engineering societies-AIME, IEEE, ASME, and ASCE-to an engineer who has rendered important public service. James Boyd is no ordinary engineer (see box). A few weeks ago, Dr. Boyd took time out of his busy schedule to stop at MINING ENGINEERING'S editorial office for the following exclusive interview.

Jan 1, 1976

By Carl G. Consalus

The Kemmerer Coal Company's Sorensen Mine is located approximately 7 miles Southwest of the Town of Kemmerer, Lincoln County, Wyoming. The coal it produces is delivered via conveyor directly to Utah Power and Light's Naughton Steam Generating Plant. The Plant went on the line in the spring of 1963 and the Sorensen Mine has been producing coal since February of that year. In this period, approximately 2, 000, 000 tons of coal have been delivered to the Plant. Present Sorensen mining operations are being carried out in the upper seams of the Adaville Formation. The formation contains, in some places, up to 30 coal seams of varying quality and thickness. Thirteen seams are considered major and are given numbers; the rest are considered splits off of the major seams and are so named. The lowest seam stratigraphically is the No. 1, or Elkol seam. So far, it has not been committed to power production but is being held in- reserve. It is the thickest seam with 80-90 feet of coal as its average thickness. The other major seams vary from 10-50 feet thick, with most of the seams averaging 17-26 feet of thickness. Each major seam has been opened at least once' to obtain a true gross sample of the coal's performance in the Plant.

Jan 1, 1967

By Alan R. Buehler

A mineral survey of the 67, 110-acre Raven?s Eye WSA (Wilderness Study Area) in the north-central Snake River Plain of Idaho was conducted by the U.S. Bureau of Mines in 1985, at the request of the Bureau of Land Management. The WSA is in Blaine and Lincoln Counties; the northwest corner is about 1 mile east of Carey, 10. A search of county mining claim records indicated that no claims have been located in the WSA. Basaltic lava is the only rock type exposed within the WSA. A platy variety of lava (slab pahoehoe) occurs that is produced from other lava fields in southern Idaho. The material is marketed as decorative stone, used for wall veneers, and retails for approximately $125/ton. Within the W5A, approximately 18,000 tons of indicated reserves are concentrated in two areas, and a total of 12,000 tons of indicated subeconomic resources were found at six other localities. An additional 10,000 tons of inferred subeconomic resources are unevenly distributed over the remainder of the WSA.

Jan 1, 1986

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By B. C. Alberts

Planning the use of South Africa's energy resources, especially coal, is of the utmost importance. The State and the mining industry require reliable official estimates of the economically mineable coal reserves for planning purposes. An overview of al the previous reserve estimates is given, with specific attention to the two most recent estimates-those of Petrick and De Jager. The differences between these two estimates are highlighted. The following important aspects are discussed: . the need to update the information regarding South Africa's mineable coal reserves, . the necessity of understanding and agreement between the coal-mining industry and the State department responsible for updating the coal-reserve data, and . the importance of the specific assumptions used in the updating of the data. A downward adjustment of mineable reserve figures is proposed, and the factors that influence the meaningful exploitation of the coal reserves are discussed. A recommendation is made as to how the Waterberg coal reserve should be exploited, and it is concluded that the Soutpansberg Coalfield cannot be exploited economically in the foreseeable future. An evaluation of the status of the coal-export trade is made and compared with the assumptions and targets set at the start of the coal-exportation scheme. The comparison shows the extent to which the exploitation of the coal reserves is being negatively influenced by the current market situation. Recommendations are made regarding planning for the coal-export market, and the aspects that have to be taken into account to keep South Africa in the export market are identified. Reference is made to the fact that the present unrestrained wage and salary adjustments, which show a total disregard of South Africa's poor productivity record, require serious thought and speedy rectification if the country is to survive in the export market. A salary and wage strategy must be developed to suit the specific needs of the Republic of South Africa.

Jan 1, 1987

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018

By Gustavo Elói de Sá Lima

A estratégia de manutenção de locomotivas da VLI sofreu significativa modificação após a implementação de propostas de consultores americanos, baseadas principalmente, na execução de atividades fora de oficina, realizadas em estruturas chamadas de “Track Service”, estruturas as quais contam basicamente com uma vala para inspeção na parte inferior das locomotivas. Dessa forma, foi possível capturar diversos ganhos em custeio e redução de investimentos, como por exemplo o aumento de periodicidade entre manutenções preventivas e redução do projeto da nova oficina de Paulínia.

Oct 30, 2017

By Ronie Magno Pinheiro de Souza

A partir do segundo semestre de 2013, iniciou-se um período de maior dispêndio energético para o controle da resistência à compressão da pelota AFXX. A este problema somou-se o desafio de atingir elevados patamares de produção e chegar à produção nominal da usina. Desta forma, foi necessário fazer a partir de um complexo diagnóstico de todas as etapas do processo para encontrar a causa do problema e determinar a melhor forma de contorná-lo. Observou-se uma elevada geração de superfície específica granular somada à dificuldade de obter granulometria (-325#) na moagem, além da elevação da umidade do filter cake. Além disso, observou-se uma considerável elevação do PPC (perda por calcinação) no período, o que explica as constatações anteriores. Os objetivos do trabalho são avaliar os efeitos do aumento do PPC no pellet feed na produção da pelota AFXX e buscar explicação para a queda da resistência à compressão.

Aug 1, 2018

By Ismar Antônio Sardinha

Usually outer straight steel tubes are used to blow supersonic oxygen into LD converters (BOF) to make liquid steel, although conical tubes are used too. Inner tube for oxygen blow and intermediary tube for water IN and water OUT are normally straight steel tubes. Present paper shows the influence of outer tube shape and metal used to in lance cooling and, consequently, a skull retention on lance surface. There are two parameters more important related to lance cooling: velocity of water out and the total lance cooling by addition of thermal conductivity of outer tube metal to it. For this comparison outer tubes are made of carbon steel or copper, and can be straight or conical. As related to velocity of water OUT, outer straight tubes have bigger efficiency than conical tubes. As related to total lance cooling, outer tube metal made of copper has much bigger efficiency than steel because of its thermal conductivity 7 to 12 times more depending on work temperature. The lance cooling has much bigger efficiency for the patented SKULLS3® technology with no skulls on the lance and no skulls into the mouth of LD converters (BOF).

Aug 17, 2017

By Thiago Pinto Silva

Este estudo teve como objetivo investigar o efeito da substituição da dolomita por magnesita como fonte de MgO no processo de sinterização. Em testes realizados em escala piloto, observou-se que a utilização de magnesita eleva a resistência mecânica do sínter. A diferença de resistência foi decorrente da formação de uma solução sólida entre magnésio e ferro durante a sinterização. No caso da dolomita, que é fonte tanto de cálcio quanto de magnésio, a solução sólida Mg-Fe promove o encapsulamento do cálcio no seu interior, o que dificulta a formação das fases mineralógicas que promovem o endurecimento do sínter. Assim, a participação do cálcio na formação das fases ligantes é inibida, limitando a resistência mecânica obtida. A magnesita, por sua vez, não apresenta cálcio em sua constituição, sendo esse elemento adicionado via calcário. Dessa forma, o efeito do encapsulamento do cálcio não ocorre, havendo grande disponibilidade desse elemento para a formação de fases ligantes, permitindo a obtenção de níveis mais elevados de resistência mecânica do sínter. Portanto, a substituição da dolomita pela magnesita mostrou-se viável, desde que a granulometria seja similar à da dolomita, com grande potencial de melhora produtiva da sinterização industrial.

Oct 30, 2017

By Mônica Aline Magalhães Gurgel

O presente trabalho estudou a evolução microestrutural durante o recozimento no campo intercrítico de um aço baixo carbono com micro-adição de nióbio e molibdênio, laminado a frio, destinado a indústria automobilística, sendo este material da classe dos aços bifásicos. Com o intuito de verificar se os parâmetros utilizados no processo de fabricação (laminação a quente e a frio em função de uma determinada composição química) foram definidos de forma eficaz para obtenção da microestrutura esperada para um material “Dual Phase”. Os estudos foram suportados pelas análises da evolução microestrutural durante o processo de recozimento em escala laboratorial e análise dilatométrica, com o objetivo de determinar a faixa de temperatura no tratamento de recozimento em que as melhores propriedades foram atingidas. As caracterizações microestruturais e mecânicas foram avaliadas por Microscopia Óptica, Microscopia Eletrônica de Varredura (MEV) e ensaios de dureza Vickers.

Jul 30, 2018

By Jorge Luiz Soares do Couto

O presente trabalho tem como objetivo realizar uma análise comparativa do comportamento de quatro metais de solda obtidos pelo processo arame tubular de forma a avaliar o efeito da relação Ni-Mn nas propriedades mecânicas. Foram soldadas juntas multipasse, com consumíveis da classe 110ksi de resistência mecânica, preaquecimento de 200°C, corrente contínua e posição plana e aporte térmico nominal de 1,2 kJ/mm. Após a soldagem, realizaram-se ensaios mecânicos e metalográficos em corpos-de-prova retirados integralmente do metal depositado, na condição de como soldado e após tratamento térmico pós-soldagem. Os resultados mostraram que as melhores propriedades mecânicas foram obtidas para uma composição contendo 1,35%Mn e 2,50%Ni. Adicionalmente, verificou-se que o tratamento térmico pós-soldagem propiciou uma redução da tenacidade ao impacto dos metais de solda de maior resistência devido à precipitação de carbetos nos contornos de grão.

Aug 7, 2018