Search Documents

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited's T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By B. Kraus

Many of us who have interacted with senior executives from leading oil and gas companies over the last few years on the subject of HSE performance have observed a marked shift in their engagement on this aspect of their business performance. There seems to be a shared impression that HSE performance will have markedly increased impact on their businesses going forward. On the back of this very real concern, many are taking material actions to secure a step change in their safety and environmental performance: hiring respected mainstream operational personnel to lead their HSE function; investing in capacity/skills development for HSE professionals to increase their effectiveness in addressing the needs of the business; taking a hard look at the efficacy of established management and audit programs (too much paper, not enough results?); investing in information management systems so they can have access to real time reliable performance indicators; and, critically, initiatives to reduce accident statistics (especially focused on fatalities and contractors? activities) and deliver meaningful reductions in their environmental footprints. Underpinning all of these actions is a clear sense that substantial, very well-intentioned activity and investment in HSE aspects of the business has not been hitting the mark and yielding too little return in terms of performance improvement. The very serious recent events on the US Gulf Coast and at a refinery in the US Pacific Northwest have added fuel to this fire. The need for approaches which will secure a step-change in performance on the front line in the global oil and gas industry has never been greater.

Jan 1, 2011

By D. B. Paterson

In view of decreasing head grades, the relatively high gold price, and recent developments in metal evaluation, an exercise was initiated to determine the extent of gold concentration, the mode of occurrence, and the areas of concentration within the run-of-mine milling circuits of Randfontein Estates Gold Mining Company (Witwatersrand) Limited. The total gold content of three of the thirteen run-of-mine mils in the Group was measured as a typical lock-up of approximately 200 kg per mil. The majority of this gold was concentrated either behind the grid-type body liners or within the pockets of the body liners. This paper is an account of the experimental procedure and the results obtained, and highlights possible means of limiting gold lock-up in future.

Jan 1, 1988

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961

By John E. Willson

Typical of southwestern Wyoming are coal structures that dip from 4 degrees to 17 degrees. Those at the Reliance and Winton mines of the Union Pacific Coal Company average 9 1/2 degrees and 15 degrees, respectively, and dip almost directly to the west. By using a hoist for main haulage. a method of mining has been developed whereby four places are driven on the pitch of the seam. Slightly upgrade from the strike at intervals of 300 feet, a two-entry system is driven to the north and to the south. In both fields, which are non-gassy, an exhaust system of ventilation is used. Slope, manway, and lower or haulage entries are placed on the intake. Two air-courses and upper or breaking entries are placed on the return. A retreat system of mining is used exclusively. From the opening of its first coal mine, in the year 1868, until 1923, when the Joy Loader was introduced into the Union Pacific Coal Company's operations, slopes, aircourses and manways were driven by hand. Development work was conducted on the night shift or off shift, and the main hoist was used for haulage. The slope was driven down the pitch with crosscuts turned at intervals of 75 feet and entries at 230 feet. Connections to the workings above were made by driving up the pitch 75 feet. Mule haulage was used to furnish cars to the hand loaders driving planes up the pitch. A sheave was placed at the upper end of the plane with a 1 1/4¬ inch hemp rope doubling around it and having one end attached to the car and the other to the mule. The mule, pulling downhill, raised to the working face a small wooden car of one-ton capacity.

Jan 1, 1941

Optimisation of the Advanced Automation System at Inmet Mining's PyhSsalmi Mine, Finland

Sep 13, 2010

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary's river, is 3,700 feet. To th'e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By H. G. Fleshman

?Wyoming bentonite? has become almost a world-wide trade mark for high quality sodium bentonite. Although bentonite is produced in more than a dozen U.S. states the largest producing area covers Wyoming and adjacent parts of Montana and South Dakota. Bentonite was originally known as Taylorite and later renamed Bentonite by Dr. Sam Knight, the State Geologist of Wyoming. The new name came from the Fort Benton shale member of the Mowry Formation. Bentonite is a clay consisting essentially of the montmorillonite group of minerals. Since bentonite has good ion exchange capabilities, various cat-ions are easily replaced. These cations are usually calcium and sodium; however, magnesium, lithium, potassium, and others can be exchanged. One way of classifying the clay is based on its swelling capacities when wet or added to water. Bentonite having sodium as the dominant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium is more abundant than other ions has much lower swelling properties than sodium varieties.

Jan 1, 1987

By Alvin Kaufman

Following the gold discoveries of the late 1800's much was written regarding the vast mineral resources of Alaska, and much interest was aroused, and yet over the years little has been done to exploit those resources. Between 1906 and 1935 the Kennecott copper mines of the Copper River region were the keystone of the mineral economy (fig, 1). After the depletion of the Kennecott ore reserves and aided by the statutory rise in the price of gold, the yellow metal became the major mineral commodity. In recent years it has shared the honors with coal and sand and gravel. Although this trend should indicate the development of a stable, diversified mineral industry, yet the trend of production is downward. This report results from a study by the Federal Bureau of Mines to delineate the problems and to forecast the growth of the mineral industries in Alaska. The need for such a blueprint for the future was enhanced by the population explosion in the United States and the consequent eventual need for additional living space, as well as the current interest in new areas, and the necessity to develop reserves of strategic minerals.

Jan 1, 1961

After a short presentation of the Division of Mining at the Royal Insti- tute of Technology, Stockholm, Sweden, the author presents some of-the fill research carried out at the Division. Literature surveys and testing methods and equipment are described. The use of flocculants' in hydraulic filling has been tested both in laboratory and in mines and the results are very promi- sing. Finally compressibility investi- gations and some finite element calcu- lations are presented.

Jan 1, 1973

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

By C Woodfull, S Munroe

Geological uncertainty is reduced by improved understanding of the relationship between regional-scale geological basement features (structure, composition, depth) and known local structural risk (such as recognised structural hazards at the mine). Coal mining and exploration entities can be more efficient and effective in managing geological risk at a range of scales. A more efficient and effective performance in forward interpreting and managing geological risk will result in a more efficient and effective exploration and also incremental or even significant mining cost improvements. In order to improve the understanding of basement features, a new 4D regional structural/basin framework for the Sydney Basin and the eastern part of the Gunnedah Basin has been constructed to provide primarily coal exploration and mining with a more integrated geological framework for ongoing subregional to mine-scale geological risk based studies. The model has been developed from a range of available regional geophysical and geological datasets, of variable detail and reliability, which have been brought together to generate a more robust structural and tectonic model than could be generated with any one single dataset. An initial regional structural model for the Sydney Basin was constructed in 2003 and an update to the model was released in 2005 (SRK Consulting, 2003; 2005). The development and ongoing refinement of the model was undertaken with financial and data support from a number of coal mining industry, gas exploration and government organisations. Prior to, and following the development of the regional structural/basin model and associated Information Base, a number of more area-specific studies have been completed, using the æbasement upÆ assessment approach. The methodology for developing comprehensive structural models, from the basement up, is outlined. The approach can be applied at a country-wide, regional or lease area scale. Case examples of where this approach has been used as an effective and efficient method in improving geological certainty and as a predictive tool to help manage geological risk are also presented.

Jan 1, 2006

By T E. Hayward, D H. English, S J. Smith

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By J. F. T. Agapito

Significant increases in extraction ratio on the order of six to eight percent, equivalent to as much as 142 t/m of panel advance, have occurred at the Big Island Mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-laying trona beds at depths of 250 to 260 m in the Green River Formation in south-western Wyoming.

Jan 1, 1988

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other stat is tics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d?Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964