Search Documents

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By J. W. Thompson

MINERALS OWNERSHIP AND POSSESSION. The owner of minerals under a conveyance from the surface owner does not lose his right or his possession by mere nonusage of the minerals. McBeth v. Wetnight (Indiana), 106 Northeastern, 407, p. 410, October, 1914. QUIETING TITLE TO MINERALS-PLEADING. A complaint in an action to quiet title to minerals and to the min- eral rights in certain land is insufficient in the absence of a direct allegation of possession, although it avers that the plaintiff from the time of receiving the conveyance assessed the mineral interest for taxes each year and paid the taxes thereon and exercised various acts of ownership of such mineral interests, in that he caused test pits to be dug on the land for the purpose of exploring the minerals and ascertaining their quality and extent, in going upon the land and looking after them from time to time, and that he accompanied or caused his agents to accompany prospective purchasers of such mineral interests and exhibited the same to such prospective pur- chasers in efforts to sell them. Fowler r. Alabama Iron & Steel Co. (Alabama), 66 Southern, 672, p. 673, Novem- ber, 1914. SALE BY MARRIED WOMAN-VALIDITY. A conveyance by a married woman of the mineral rights in certain described land is void where she had previously conveyed the land to another grantee who had acquired title by adverse possession under the deed.

Jan 1, 1915

By Frederick L. Hoffman

Miners' nystagmus is the result of a peculiar form of eyestrain, which often results in impairment of vision and a consequent diminu- tion of the wage-earning capacity of the workman. Historically it has been pointed out by Shufflebotham that "This disease was first recognized by Gillett, of Sheffield, about 1854, although no case was mentioned in medical literature until 1861, when the symptoms were described by De Conde, a Belgian physician. Cases were reported by Pepp Müller as early as 1860, by Von Graefe in 1873, and by Bell Taylor, of Nottingham, and by Nieden in 1874. In this country (England) we are indebted to a very large extent to the observations and writings of the late Simeon Snell and for his pioneer work on this many-sided disease; in France Dransart occupies a similar position." In the treatise on "The Effects of Arts, Trades, and Professions," by C. Turner Thackrah, published in London in 1832, it is stated that- The complexion of the colliers, even after the removal of the dirt, is generally sallow and unhealthy. Their eyes, from the swelling of the lids, appear small, are affected with chronic inflammation and intolerant of full light. * Sickness and vomiting sometimes affect persons at their commencing the employ; and many, after a few years' trial, are obliged, by the injury which their health has sustained, and especially by the weakness of their eyes, to leave the mine. According to Greer, an authority on industrial diseases and acci- dents, miners' nystagmus occurs in 5 per cent of all miners, but it is quite probable that the reference is to European coal miners rather than to men employed in all branches of the mineral industry. According to the same authority, miners' nystagmus "is associated with a twitching of the eyelids and with considerable diminution of the range of movement of the eyes, and is particularly liable to occur in patients whose vision is subnormal owing to errors of refraction, especially astigmatism. It causes much inconvenience to those suf- fering from it and prevents them from following their usual occupa- tion as, owing to the movements of the eyes, everything at which they look appears to be in a state of perpetual motion, and in conse-

Jan 1, 1916

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By H. H. Clark

The term "explosion-proof," as applied by the Bureau of Mines to an electric motor, refers to a motor inclosed by a casing so constructed that an explosion of a mixture of mine gas (methane) and air within the casing will not ignite a mixture of the same gas surrounding the motor. There are two classes of motors so constructed: First, a totally inclosed class built strong enough to withstand high internal pressures and so designed that the efficiency of all inclosing covers can be satisfactorily maintained; second, a class provided with relief openings or valves designed to relieve the pressure of an explosion within the motor casing and to cool any products of combustion dis- charged through the valves. A satisfactory motor of the first class is much more expensive to build than an equally safe motor of the second class. For this rea- son, attempts to make motors explosion-proof have been confined chiefly to motors of the second class.

Jan 1, 1912

By Arno C. Fieldner, Howard I. Smith, J. W. Paul, SAMUEL SANFORD.

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1,1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.a Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.b The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1913 to 1916. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22 and 85, the same plan of geographical classification has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1918

By Charles Janin

The recovery of gold from sands and gravels is one of the oldest forms of mining; it antedates history and has been practiced by savage peoples. In North America the search for placer gold has been a powerful agency in the exploration and development of unknown regions and has profoundly influenced the course of our civilization. With the progress of invention, the improvements in machinery, and the availability of large capital for the conduct of great operations, the tendency in placer, as in many other branches of mining, has been toward the working of extensive but comparatively low-grade deposits. The early miner washed the rich spots in stream beds or terraces with his pan, his long tom, and his primitive sluice. Then followed the growth of hydraulic mining and the use of giants supplied with water under pressures of hundreds of pounds to the square inch that could work at a profit gravels whose gold tenor was less than 3 cents to the cubic yard. Finally came the dredge that could handle deposits lying so far below water level as to be beyond attack by other methods. Although the gold dredge was first successful on a commercial scale in New Zealand, it has reached its present strength and efficiency in this country and its development is a monument to the daring, per- severance and technical skill of the many men, mine owners and engineers who have each contributed something to the final result. The Bureau of Mines, authorized to conduct investigations for the purpose of increasing efficiency in the mineral industries, had its attention called some years ago to the need of a comprehensive report on gold dredging in the United States. The director of the bureau recognized that such a report should summarize the development of the gold dredge, should describe in detail the essential features of present-day dredges, should discuss the facts that determine whether a placer deposit can be profitably dredged, and should point out the approved methods of prospecting placer ground and of operating dredges. At the request of the director, the author undertook the preparation of such a report and has been intermittently engaged on the task for several years. This bulletin is the outcome of his labors. He hopes that it will prove of interest to designers and builders of dredges, to mining engineers, and to persons who may contemplate investing capital in placer-mining ventures.

Jan 1, 1918

By Ira E. Sproat

The question "Why can not American kaolins be substituted for English china clay?" has been asked time and time again, and more often since the beginning of the present war in Europe, which has threatened to cut off the supply of European clays imported from abroad. The answer to this question has invariably been, that the domestic kaolins are not as pure and uniform in composition as the imported clays. This demand for white-burning American clays is of such economic importance that it was considered advisable to determine whether some of our vast deposits of impure white clays could not be refined sufficiently to permit their being substituted for the foreign materials. Up to the present time mechanical principles only have been applied in the refining of kaolins, but in order to keep pace with the increasing requirements for better quality and uniformity of product, the application of the principles of colloidal chemistry is necessary. The investigation described in this report was carried on to deter- mine the practicability of applying technical control of clay disperse systems to the refining of kaolins and the utilization of the prepared clay in the manufacture of vitreous china and wall tile. It is hoped that this report will prove a stimulus to the clay- washing industry; will point out a method of refining certain Amer- ican clays, and will lead to the substitution of domestic kaolins for imported china clays by manufacturers of high-grade ceramic wares.

Jan 1, 1916

By GEORGE S. POPE

This bulletin is a revision of Bulletin 63 and is published by the Bureau of Mines in order that purchasers of coal for Government, State, municipal, or private use may be informed regarding advances or refinements in sampling coal deliveries and preparing specifications for the purchase of coal. The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form, but the same in principle, has been gradually adopted by other departments until, at present, of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publioations a listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples representing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the specification method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly representative of the commercial product delivered in wagons, railroad cars, or ships. Therefore the method of taking and preparing samples for shipment to the laboratory has been given fully as much care as the making of the analyses and tests, and a general plan of collecting samples fairly representative of the delivered coal has been evolved through various modifications and improvements based on experience and increased knowledge of the physical and chemical characteristics of the various coals that are purchased by the Government. The method that is in general use by the Government is described in the following pages. In connection with studies of the coal deposits of the country, of the best methods of preventing waste in mining, and of increasing efficiency in the utilization of coal belonging to or for the use of the Government, geologists and engineers of the United States Geological Survey and of the Bureau of Mines have visited more than 2,500 coal mines scattered through all of the coal-producing States and Territories. From each mine 2 to 8 or more samples were taken, the number depending upon the size of the mine and its output. The analyses and descriptions of the samples collected up to the end of the fiscal year 1913 are published in Bureau of Mines bulletins 22 a and 85,b and those of samples collected in the fiscal years 1914 and 1915 are presented in a bulletin that will soon be published by the bureau. A study of the analyses of these samples and of the samples taken from cars shipped from a number of the same mines shows that the mine samples are as a rule of higher grade than the average commercial shipments, particularly with respect to containing a lower percentage of ash and having a correspondingly higher heating value. This difference is due to the fact that the Government inspector, proceeding on the basis of what can be done by a good miner, usually removes more of the partings of bone, slate, and other extraneous matter from his mine samples than the average miner does in ordinary practice, the aim of the miner being to get the maximum number of tons past the tipple inspection, as his earnings are based on his output. The average miner, therefore, does not always take as much care as he might in rejecting the impurities. The difference may be caused, too, by the presence of pieces of the mine roof and floor in commercial shipments. The Government inspector can readily

Jan 1, 1916

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lowergrade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful largescale concentration of low-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district. While studying iron-mining methods in the United States for the Bureau of Mines, Dwight E. Woodbridge, consulting mining engineer of the bureau, was impressed with the importance of this problem, and believed it merited the attention of the bureau. Accordingly, Mr. Woodbridge had Mr. W. J. Penhallegon, general superintendent of ore mines and quarries of the Republic Iron & Steel Co., of Birmingham, send the author of this report five samples of the unworkable siliceous ores of the district. The results of concentration experiments with these ores made a more thorough 'and systematic investigation desirable. In consequence, the author subsequently collected samples in the district, and these became the basis of the experimental work described in this report. The results are published by the Bureau of Mines as a part of its efforts to increase efficiency in the utilization of mineral resources. The experiments were conducted in the geological laboratory of the Johns Hopkins University, Baltimore, Md., with the aid of Raymond Leibensperger, mining assistant. The chemical analyses were made by A. C. Fieldner, chemist, of the Bureau of Mines. The author wishes to express his appreciation of the courtesies extended to him by the mining companies of the district, and particularly to Mr. W. J. Penhallegon, of the Republic Iron & Steel Co. Thanks are also due Prof. W. B. Clark, director of the geological laboratory of the Johns Hopkins University, the unrestricted use of the facilities of the laboratory.

Jan 1, 1917

By FRANKM. SEIBERT, G. G. Oberfell, GEORGEA. BURRELL

The Bureau of Mines is conducting a series of investigations with the common aim of minimizing the losses that occur in the mining and treatment of mineral substances. The results of the investi- gations are being published in reports of the bureau. This report treats of a method of preventing some of the waste of the natural gas incidental to oil mining. This method, the condensation of gasoline from natural gas, offers to the oil operator and others a profitable means of utilizing some of the oil-well gas now being wasted. The most desired constituent of crude oil is obtained, the production of oil is not hindered, and the gas, after the extraction of gasoline, can be returned to the leased area to drive pumps or into pipe lines for uses to which natural gas is ordinarily put, usually with its fuel value lessened only in slight degree. Publications already issued briefly discuss the subject. In this report the work is treated in greater detail, and the results of many additional tests are shown.

Jan 1, 1915

By John Hays Hammond, James Douglas, J. PARKE CHAN- NING, W. R. Ingalls, J. R. Finlay

The committee making this report, consisting of Walter Renton Ingalls (chairman), J. Parke Channing, James Douglas, James R. Finlay, and John Hays Hammond, was originally appointed at a meeting of the American Mining Congress at Denver, Colo., in No- vember, 1906. The object of this appointment was the drafting of a modern law governing quarrying and metalliferous mining which could be recommended to the several States for adoption, in the hope that the passage of such a uniform law by the mining States would tend to lower the number of fatal and serious accidents. The first step of the committee (the personnel of which has re- mained unchanged from the beginning) was to procure copies of existing laws from the officials of the several States of the Union. With the assistance of the Engineering and Mining Journal, copies of the laws of Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New Zealand, and certain European countries were also obtained. The replies to the inquiries made at that time developed the fact that a number of States in which mining was carried on had no laws at all. Other States were found to have elaborate provisions regulating coal min- ing, but none applying to metalliferous mining. Still other States were found to have miscellaneous and unrelated provisions passed at odd times, seemingly as the result of the occurrence of some dis- aster or other.

Jan 1, 1915

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By H. W. Gillett

This bulletin is issued by the Bureau of Mines as a contribution to the increase of safety and efficiency in the preparation and utilization of the mineral resources in the United States. Notable among the drains on these resources are the demands made by the nonferrous- metal industries, and in these the losses occasioned in melting brass and bronze are worthy of particular attention. This statement will be better appreciated by a consideration of the size of the brass industry.

Jan 1, 1914

By D Kentwell

IGO Ltd’s (IGO) Nova Operation (Nova) is 160 km east-north-east of the town of Norseman in Western Australia (WA). Discovered by Sirius Resources NL (Sirius) in 2012 and acquired by IGO in 2015, the Nova-Bollinger Deposit (Nova-Bollinger) occurs within the Fraser Zone of the AlbanyFraser Orogen. Nova-Bollinger is a complex nickel-copper-cobalt (Ni-Cu-Co) magmatic intrusive sulfide deposit, which is characterised by high-grade folded and undulating breccia lodes that host the bulk of the payable metals. Significant sulfide mineralisation is also found in several magmatic intrusive styles including net-textured, disseminated and blebby styles. A smaller but material volume of sulfides has also been remobilised into the deposit’s footwall rocks as ‘stringer’ bands in metasediments, or as discrete massive sulfide lenses. When interpolating Mineral Resource estimate (MRE) block grades in the presence of locally varying grade connectivity trends, such as folds or undulations, the sample search neighbourhood, which is used to identify the composites subset that is used for each block estimate, should be oriented to match the local trends. In theory, the most robust method of estimation where locally varying angles (LVAs) are applied to search neighbourhoods, are techniques where the composites and the blocks to be estimated are transformed to an unfolded coordinate system (UCS). However, UCS methods can be tedious to implement and require subjective decisions to be made that cannot always be fully defended. An alternative LVA method commonly used in the industry is dynamic anisotropy (DA), which is much simpler to implement and is often assumed (but not that often demonstrated) to result in similar results to UCS-style estimation. In 2018, Nova’s Mine Geology team (MGT) estimated the grades and density of the Nova-Bollinger MRE using the UCS approach. For the 2020 MRE update, Nova’s MGT tested and compared the USC grade interpolation method with the DA approach. As applied to the Nova-Bollinger’s 2020 MRE, the comparison, advantages and disadvantages of the two estimation methods are the subject of this paper

Mar 22, 2022

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By S Tierney, D Cumming-Potvin, I Thin, Y Potvin, D Grant

The preliminary modifying factors for future stope design in the Southern Mine Area of Olympic Dam consisted of only a single, arbitrary value of Equivalent Linear Overbreak/Sloughing (ELOS). In order to improve this, a study was conducted which developed a more comprehensive methodology for assigning ELOS, Equivalent Linear Lost Ore (ELLO) and Equivalent Linear Fill Overbreak (ELFO) to individual stope faces based on geotechnical and mining parameters. The approach used was to look at the simple cases, which were classed as vertical stope walls in good ground (RQD 80-100%), divided into wall orientations (North, South, East, West). The stope walls were also split based on the blasting practice used (toeing, parallel or a combination of the two). The expected ELOS and ELLO from these ‘base cases’ are then modified by parameters which have historically been found to affect stope performance (Hydraulic Radius and Q’). The size of the effect found in the historical data determines the ELOS / ELLO applied. The methodology was summarised in an easy to use flow chart and was applied to all of the proposed stope shapes for the Southern Mine Area and summarised per mining block. This allowed each iteration of the mine plan to be assessed in terms of overbreak (both rock and vertical fill exposures) and underbreak.

Mar 15, 2021

By G Sartor, A Rich, D Grimsey, R Forzatti, M White

An in-depth process model was developed for the pyrometallurgical, off-gas systems and water balance of the Kalgoorlie Nickel Smelter. This model was used to assess plant capacity with changing concentrate grades, increased throughput and tighter environmental emissions under a range of potential future operating conditions. Comparison of modelled results allowed for flow sheet optimisation across a range of metrics including sustainability, processing capacity and costs. Process modelling software, METSIM® (ver 2020.06 by METSIM International), was used to simulate the flash furnace, integrated electric slag cleaning furnace, Pierce-Smith converters, matte granulation, waste heat boiler, hot gas handling equipment, wet gas cleaning plant and acid plant. The METSIM® model was divided into three separate, yet interconnected models: metals, off-gas and water balancing. This allowed for improved modelling efficiency and traceability while minimising manual error. The METSIM® model was supported by inputs from other specialised software. Chemical thermodynamics software, FactSage™ (ver 8.2 by GTT Technologies), was used to establish relationships for the flash furnace fluxing strategy and determine the operating temperature. Arena® (ver 16.0 by Rockwell Automation), a discrete event modelling software, was used to simulate material movements within the aisle as well as Pierce-Smith converter operation, allowing for integration with upstream and downstream systems. A dynamic data exchange (DDE) was used to connect the results of each software package, interfacing through Excel® (version 4203 by Microsoft). The integration between models provided a streamlined approach to test capacity, bottlenecks, water consumption and emissions under a range of operating conditions, enabling a more robust process. Further downstream modelling techniques were used to assess mechanical equipment. METSIM® outputs provided key parameters for combustion assessments using computational fluid dynamics and finite element analysis for the furnace mechanical design.

Aug 21, 2024

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021