Search Documents

By João Victor Gomes Guimarães Ananias, Itavahn Alves da Silva, Thiago Araújo Santos de Oliveira, Salvatore Giuliano Peixoto Tropia de Abreu, Guilherme Santiago Queiroz, Carlos Antônio da Silva

Oct 1, 2019

By Marcelo Ferreira Martins, Breno Totti Maia, Sandro Luís Zahner, Leandro Martins Perreira, Paulo Roberto Ogliari Hopperdizel, Geraldo Vieira da Silva

O reator EOF foi desenvolvido no Brasil nos anos 80 com características únicas. O pré-aquecedor de sucata e a distribuição dos pontos de injeção de gases oxidantes e combustíveis conferem estas características. Um reator dinâmico e versátil capaz de adequar-se a grandes variações de carregamento de gusa e sucata, porém com equipamentos de injeção calcados ainda nos princípios da concepção da tecnologia. O objetivo deste trabalho é apresentar a etapa 1 de uma seqüência planejada de 3 etapas os desenvolvimentos que visam o aumento de produtividade do EOF. Nessa etapa 1 são apresentadas os ganhos relativos a modificação do número de pontos de injeção de oxigênio e a adequação desses pontos para condição supersônica de sopro.

Oct 1, 2019

By Raquel Húngaro Costa, Jonathan Tenório Vinhal

The demand for natural resources has grown over the years, however, the environment offers a limited amount of these resources for exploration. Then, the investigation of new methods for recovering and reuse some compounds and elements are essential to know later tailings purposes. Zinc is used in corrosion resistance as a protective coating for several products. One of the steps for the extraction of zinc is by flotation process to obtain the concentrated ore, in which a residue is generated. The aim is to characterize this residue, allowing the choice of recovery routes for compounds and elements in future stages. The methods of analysis were Malvern, VA, Eltra and ICP-OES, besides the water content. In this study, a characterization of elemental chemical analysis was performed, in which the main elements presented were: calcium (17.4%), magnesium (10.3%) and iron (7.97%); the water content was 27% and the grain size of the material presented an average size of 50μm. With the presented characteristics the material can be used, after treatment, in the recovery of other compounds for applications in the sector of fertilizers, ceramics and steel industry.

Oct 3, 2019

By Daniel Horta Fernandes, Walter Gomes de Albuquerque, Adriano Cesar Carvalhido, Victor Dias Martins

O trabalho apresenta a experiência recente da troca de 38 staves contribuindo no prolongamento da campanha operacional do Alto-Forno 3. Durante 13 dias ocorreu a substituição dos Staves originais de FoFo instalados em 1999 por novos Staves de cobre fundido. Além da recuperação do sistema de refrigeração, a mudança no material dos Staves contribui para maior troca térmica favorecendo a formação carga inativa (cascão) que protege os Staves e o corpo do Alto-Forno. Esta substituição foi fundamental para recuperar a estabilidade da temperatura da carcaça e prolongar a vida útil do equipamento até o final de sua campanha. Diversos aspectos do projeto serão apresentados: engenharia, metodologia, planejamento, segurança, qualidade técnica, cronograma e outros.

Oct 1, 2019

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Dagoberto Brandão Santos, Dalila Chaves Sicupira, Graziele Gianini Braga Maria, Jéssica Caetano Fortes Monteiro, Raphael França Assumpção

O objetivo desse trabalho foi avaliar o efeito do tempo de recozimento na resistência à corrosão do aço inoxidável duplex UNS S32205 laminado a frio. Quando o aço duplex é submetido a deformações intensas, a austenita transforma-se parcialmente em martensita, elevando a resistência mecânica do aço. Já quando é feito o recozimento essa transformação é revertida, ou seja, a martensita se transforma em austenita. Porém, esses aços apresentam forte tendência à formação de fases secundárias quando expostos a determinadas temperaturas por certo intervalo de tempo, que levam à deterioração das propriedades mecânicas e corrosivas dos mesmos. O aço estudado foi submetido à laminação a frio até 60% de redução da espessura, e posteriormente recozido a 850°C, temperatura na qual a cinética de precipitação de fases é máxima, nos tempos de 300, 600, 1800 e 86400 segundos. Para a análise microestrutural foram utilizadas as técnicas de microscopia óptica, microscopia eletrônica de varredura e a difração de raios-X. A resistência à corrosão foi estudada por meio da técnica de impedância eletroquímica (EIE), utilizando solução de NaCl 3,5% à temperatura ambiente. O aumento do tempo de recozimento aumentou a precipitação das fases secundárias, o que leva ao aumento de regiões empobrecidas em Cr e Mo. Com o aumento do tempo de recozimento, essas regiões são parcialmente recuperadas pela difusão desses elementos, melhorando a resistência à corrosão.

Mar 1, 2019

By Kashyap Chaturvedula, Emad Farouz

The paper presents a discussion on the axial capacity of deep foundation elements bearing in the Yorktown formation in the southeastern region of Virginia. The fossiliferous marine soils of Tertiary age Yorktown formation typically consist of silty/clayey Sand or sandy Silt/Clay with varying amounts of shell fragments. The Yorktown formation is generally divided into Upper and Lower Yorktown layers depending on the shell content and the percent fines. Results of multiple load tests performed by Jacobs Engineering on auger cast piles as part of water and wastewater treatment plant expansion projects in southeastern region of Virginia are presented in this paper. The paper describes the subsurface investigation methods used to study the existing subsurface conditions and the design methodologies followed to estimate the axial capacity of the auger cast piles. The paper provides details regarding installation of test piles, instrumentation, load testing procedure, and interpretation of test results. The paper presents a comparison between the various methods of estimating axial capacity of auger cast piles based on the SPT-N values, the empirical methods for the Yorktown formation and the load test information. The paper distinguishes the side resistance values obtained within the upper and lower Yorktown formations. The paper compares the various design methods to the multiple load test results and recommends a design modification that is closer to the load test results.

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

By Verônica Scarpini Candido

Este estudo tem por objetivo caracterizar a escória de alto forno proveniente de uma siderúrgica do estado do Pará visando a sua incorporação em argilas para produção de telhas. O resíduo passou pela etapa de beneficiamento e, depois, foi realizada a difração de raios-X (DRX) e fluorescência de raios-X (FRX). Além disso, realizou-se também a análise morfológica por microscopia eletrônica de varredura (MEV). Os resultados mostraram que hematita, magnetita, goethite e wustita são as fases predominantes a associadas aos óxidos de ferro. A análise química por FRX mostrou que o resíduo apresenta elevados teores de sílica (SiO2) e óxidos de ferro associados a baixos teores de alumina (Al2O3). Dessa forma, a caracterização da escória de alto forno mostrou que esse resíduo apresenta-se como um potencial constituinte mássico cerâmico podendo contribuir par ao aumento da refratariedade das peças queimadas.

Oct 30, 2017

By Sushant Upadhyaya, Deniz Karadeniz, Ahmed Mohamed

Soil setup analysis provides opportunities for efficiencies in pile foundation design and installation. Soil setup gain with time was evaluated as part of the foundation design and installation for twelve bridges along the Interstate 64 corridor between York County and Newport News in Virginia. The substructure elements of the bridges consist of driven precast prestressed concrete piles or H-piles. This case study describes lessons learned to understand the soil setup phenomenon during the installation of the piles in coastal plain. We were able to make expedited decisions during construction by analyzing previously performed pile dynamic analyzer (PDA) test results within the project alignment. Data evaluation included analyses of PDA data obtained from initial driving and restrike after a few hours to 5 weeks. The test data showed pile resistance increase up to twice in most cases and as high as four times in some cases. Foundation design and acceptance based on soil setup can provide opportunities for cost savings and advanced scheduling during construction.

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

By Verônica Scarpini Candido

Diante a atual preocupação com a disposição de resíduos industriais, diferentes alternativas vêm sendo desenvolvidas a fim de que hajam aplicações referentes a utilização desses resíduos. A lama vermelha, rejeito da lavagem da bauxita, cujo a disposição final estabelece-se dentro de grandes barragens, vem sendo alvo de inúmeras prospecções para uso. Deste modo, o presente trabalho visa estabelecer uma análise comparativa da granulometria da lama vermelha a partir da sedimentação hidráulica, valendo-se da Lei de Stokes e de ensaios em granulômetro visando conhecimento para a futura aplicação em polímeros. Sendo assim, foram desenvolvidos testes experimentais em proveta para gerar dados de processo para testes em maior escala. As amostras pós-sedimentação foram analisadas em um granulômetro Mastersizer 2000-HYDROG. Verificou-se que existe uma variação significativa no tamanho das partículas de lama vermelha, e que é possível proporcionar futuramente a formulação de compósitos a partir de cada faixa granulométrica.

Oct 30, 2017

By Andrew Wetherelt

Blast vibrations are of paramount importance in a society where ever increasing development is putting more stringent requirements on their control. Increasing civil development and more complex extraction scenarios make the trade off between proficient vibration control and productivity difficult to ascertain. Historically, reduction of induced vibrations levels was achieved through a reduction of MIC’s leading to smaller but more frequent blasts in order to meet extraction targets.

Jan 1, 2007

By Werner Klein

The utilization of production facilities in an optimum way, with reliable due date fulfillment, reducing raw material and energy consumption, are challenges iron and steel companies are facing in their business every day. By using an APS system such goals can be achieved to increase the competiveness of iron and steel producers. A sophisticated APS supports the overall planning process by applying complex rules based on product and order mix, its production routings with corresponding processing and transport times and resource availability. Specific technological as well as steel grade and energy related constraints are also considered to meet company specific KPIs. A core feature of APS solution is to react online on deviations to plan during the production process. Deviations such as nonconformance of intermediate material attached to an order, sudden production delays, unavailability of important production resources, makes it necessary to update the production plan. In general the task of APS is to support the preferred work-to-order concept, by assigning work-orders to available production facilities along the product specific process route and generate optimized material sequences for critical work centers.

Aug 17, 2017

By Franz Ramstorfer

No lingotamento contínuo de placas, rompimentos de veio pelo colamento e problemas de qualidade de superfície, como trincas longitudinais, são frequentemente relacionadas à lubrificação insuficiente no molde de lingotamento contínuo devido ao pó fluxante ou a prática de oscilação inadequados. Para detectar, com vistas a prevenir, este tipo de problema de processo, um método para avaliar em tempo real o coeficiente de atrito entre o veio e as placas do molde foi desenvolvido, utilizando-se a medição da força que atua nas placas laterais do molde e as forças de oscilação. Observou-se que o coeficiente de atrito do molde é um parâmetro confiável para auxiliar no desenvolvimento de pó fluxante, na otimização de parâmetros de oscilação e no monitoramento online do desempenho de pó fluxante.

Aug 16, 2017

By Jorge Luis Braz Medeiros

As ligas de Alumínio ASTM 2014, caracterizam-se por apresentarem elevada resistência mecânica, quando comparadas a demais ligas de Alumínio. Este comportamento está associado ao tratamento térmico de Solubilização e envelhecimento, sendo que no envelhecimento artificial existem diferentes curvas de avaliação do limite de resistência, limite de escoamento, alongamento etc. Neste trabalho serão apresentados os efeitos da cura de revestimento de Politetrafluoretileno, realizado a 230ºC, nas propriedades mecânicas e na dureza, destas ligas, após a condição preliminar de solubilização. O Politetrafluoretileno confere baixo coeficiente de atrito e acabamento diferenciado, sendo comparado seu efeito com processos de anodização.

Aug 7, 2018

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007

By Isadora Pereira Nunes

O objetivo deste trabalho é estudar o efeito do recobrimento de níquel-nióbio por eletrodeposição na resistência à fadiga de um aço carbono SAE 1020. Os corpos de prova para os ensaios de fadiga foram extraídos de barras de diâmetro igual a 7,94 mm (5/16’’). Os ensaios de fadiga foram realizados por flexão rotativa com carregamento em balanço. Foi empregada uma velocidade de rotação de aproximadamente 1500rpm. Foram realizados ensaios de dureza do aço e da camada depositada de Ni-Nb. Análises microestruturais do aço e das fraturas de fadiga foram realizadas através de microscopia eletrônica de varredura (MEV). Os ensaios de fadiga foram realizados de forma a se obter curvas S-N (curvas de Whöler). Foram realizados três ensaios para cada carregamento. Foi observado que o recobrimento de Ni-Nb proporcionou tendência ao aumento do limite de resistência à fadiga do aço.

Aug 17, 2017