Search Documents

By Unnikrishnan Nair, Sandeep S. Nikam, Sanjay D. Patil, Prabir C. Basu

"Mumbai Metropolitan Region Development Authority (MMRDA) entrusted to implement Monorail Systems in various parts of Mumbai Metropolitan Region (MMR) with the objective to supplement the present transport system in MMR. The stretch of Monorail is starting from Sant Gadge Maharaj Chowk (SGMC) and extending up to Chembur Railway Station, divided into 2 phases. Construction of Phase 1 (Chembur to Wadala Depot) is complete and Phase 2 (Wadala Depot to SGMC) is under construction.Monorail runs on prestressed girder (guide beam) of span ranging from 20m to 28m supported on pier founded upon group of end bearing piles embedded in rock, pile group ranging from 2-4 piles of diameter 1000mm each.For the purpose of site characterization, geo-technical investigations were carried out along the alignment of Monorail system as mentioned above. These investigations included field and laboratory tests. The subsurface strata mainly consist of silty sand, gravel, underlain by marine clay extending up to stronger basalt rock with volcanic breccia. Overburden consisting of mainly marine clay ranging from 5.5m to 11m at all locations within the influence zone of settlement.The existing rigid pavement along of Sion-Koliwada and Anik-Wadala were constructed about 5 years prior to the construction of Monorail piers. Before laying the rigid pavement, to improve the geotechnical strength of subsoil (mainly marine clay), ground improvement using stone columns was undertaken by MMRDA. In light of limited right of way, the Monorail piers have been constructed in the median portion of the road. The line became operational on February 2014, in few months it was noticed that, in the vicinity of the Monorail piers, along Sion-Koliwada link and Anik-Wadala link, the Road Pavement Quality Concrete (PQC) panels adjacent to the Monorail piers started showing distress in form of nonuniform settlement of the concrete panels.Effect of pile foundation on pavements/PQC slab distress and possible causes of distress were investigated. Initially the distress was thought to be upheaval of monorail pier cap, but further investigations revealed the same to be soil settlement occurring over time. This paper describes the investigation carried out for identifying the cause of this settlement."

Jan 1, 2015

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By George Aristorenas, Carlos Englert, Jesús Gómez

"Laboratory test data of strain softening soils exhibit the development of a maximum (peak) shear strength followed by a decrease in the strength with continued straining. The rate of strength loss decreases such that an asymptotic minimum value, known as the residual strength, is approached. This paper presents an investigation of the evolution of strength degradation in excavation supported soils that exhibit strain softening behavior. The paper presents a numerical investigation of excavation support of slicken-sided clay, and results of shear testing on materials with similar strain softening behavior. A strain softening constitutive law is presented that can be used with the finite element computer software Plaxis for analysis of excavation support. A typical design section of a deep excavation support in stiff, fissured clay is presented that illustrates the limitations and conservatism of the residual strength approach for excavation support design. Finally, a discussion is presented on the impact of stiffer walls such as diaphragm walls, compared to less stiff systems such as sheet piles, on the design parameters.INTRODUCTIONIn the Washington, D.C. metropolitan area, the Potomac Formation is generally composed of stiff, fissured clays. Geotechnical engineers often associate the presence of slicken-sided planes within the formation as evidence that the soil cannot develop its peak strength. Although it is unclear how old and continuous these slicken-sided planes are, their occurrence, persistence and orientation appear to be somewhat random. Due to this uncertainty, the design of open cut slopes in these materials is often conservatively performed assuming residual shear strength values. This design approach may be justified for long-term open cuts when there is limited amount of geotechnical information and in view of back stability analyses of past slope failures. Furthermore, the lack of confinement in open cuts allows relatively high shear strains near the surface and toe throughout their existence, which promote mobilization of post-peak strength values and the ensuing progressive failure. Indeed, such behavior has been discussed in the past (Skempton, 1970; Schnabel et. al., 1982; Derrenbacher, 1998). A thorough study by Mesri et. al. (2003) of numerous slope failures concludes that the lower bound strength for stability analysis of non-failed slopes is the fully softened strength, which is intermediate between the peak and residual strengths, but that part of the slip surface may be in a residual condition prior to failure."

Jan 1, 2015

By J S. J van Deventer

"Conventional wisdom is that gold not assayable is not recoverable or does not exist. There has been no formal study on the possibility that gold assays using advanced spectroscopy such as mass spectrometry and neutron activation could grossly underestimate the gold recoverable by proprietary extraction techniques. Such gold is not considered here to be æinvisibleÆ to detection but rather æabnormalÆ or ædistortedÆ at atomic level. Large-scale extraction of gold from æabnormalÆ ores has not been demonstrated, hence this emerging field still lacks credibility and acceptance. For fear of harming their reputation, few academic researchers or companies are expected to venture into this field until it is well proven. This paper aims to create awareness amongst metallurgists of the potential of æabnormalÆ gold ores by reviewing unconventional observations, the pseudoscience mainly available in non-peer reviewed web sites, and hypotheses for the recovery of ænon-assayableÆ gold, including: the occurrence of high levels of nano-sized gold in clays detectable by high-precision analytical instruments, which represents æinvisibleÆ gold accounts of ambient transmutation of elements, mainly using thermal methods orbitally rearranged monoatomic elements (ORMEs), which are virtually undetectable by conventional means, and their conversion to normal metals the possibility of a æhigh spinÆ state of transition metals the formation of microclusters altering the chemical behaviour of gold and the possibility of clustering with other elements. It is suggested here that gold in ores displays a range of clustering, from ænormalÆ gold amenable to conventional extraction to the ORME state. The concepts of æintermolecular waterÆ in forming complex salts locking up precious metals, electro-dissolution in strong acids, and electrowinning at both the anode and cathode are discussed as a means of treating æabnormalÆ gold ores. It is also possible that the gas phase extraction of gold chlorides under controlled temperature and pressure conditions, as well as transferred-arc plasma fuming of gold through carbothermic reduction of sulfides, could be used as a basis for extraction of gold from æabnormalÆ ores.CITATION:van Deventer, J S J, 2013. Is there gold that we do not recognise?, in Proceedings World Gold 2013, pp 27-34 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By F. Botha

South Africa is amongst the 40 driest counties in the world, with extreme weather conditions and beset by both droughts and floods. Coupled with economic growth is an increased demand on water resources and, as with all other industrial developments, mining requires large volumes of water, which is likely to have an impact on the environment. Further to this, the mining industry also realizes that minerals are a non-renewable resource and the contribution to wealth creation from mineral extraction is not everlasting. It serves as an economic boost and careful planning is required to ensure that the legacy of mining is sustainable, and that some of the returns from mining provide continual economic and social prosperity.

Jan 1, 2012

By S Vink, A Wolhuter

Increasingly the community and government regulators are calling for æzero dischargeÆ mines. Some mining companies are beginning to explore ways in which they can transition to zero discharge. When striving to attain zero discharge, mines must consider multiple variables in addition to water quantity. These include climate regime, water quality and regional water budgets. This paper explores the drivers behind the concept of zero discharge mines and will use examples to illustrate the feasibility of attaining this goal.CITATION:Wolhuter, A and Vink, S, 2013. Is zero discharge a viable or useful concept in mine water management?, in Proceedings Water in Mining 2013 , pp 329-334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By B Dodd

This paper details how the Australian Securities and Investments Commission (ASIC), as a disclosure and conduct regulator, approaches regulation of continuous disclosure, capital raising and control transactions in the mining and resources sector, and the reasons for the approach. In examining this topic the paper considers the Joint Ore Reserves Committee (JORC) Code (JORC, 2004), the VALMIN Code (VALMIN Committee, 2005), the relevant ASX Listing Rules and the relevant provisions of the Corporations Act 2001 (Corporations Act). This paper discusses ASICÆs approach to expert reports and disclosure with reference to Regulatory Guides 111 Content of expert reports and 170 Prospective financial information.CITATION:Dodd, B, 2012. Issues in capital raisings and disclosure, in Proceedings International Mine Management 2012, pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Sergio N. Monteiro

Polymer matrix composites have been applied in components such as helmets and shielding for which toughness is a major requirement. Natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. The objective of this work was then to assess the Izod impact resistance of polymeric composites reinforced with different amounts, up to 30% in volume, of a promising high strength natural fiber from the Amazon region known as curaua. The results showed a remarkable increase in the notch toughness with the amount of incorporated curaua fibers. This can be attributed to a preferential debonding of the fiber/matrix interface, which contributes to an elevated absorbed energy.

Jan 1, 2009

By Alexander Ciccone, John H. Gill

Jet grouting is a highly versatile ground modification technique that can offer significant commercial and technical advantages over traditional concrete pit underpinning applications. Despite these advantages, jet grouting remains an underutilized technique in the construction industry due to its perceived complexity, cost, and risk. When performed thoughtfully, underpinning by jet grouting offers significant safety and schedule advantages over traditional underpinning approaches. The New England construction market has seen a recent acceptance in the use of jet grout underpinning on congested project sites across a variety of subsurface conditions. The reduction of the cement batch plant footprint due to equipment advances has allowed the use of this technique in urban sites where its use would be previously infeasible. Furthermore, jet grout underpinning has been utilized for support of historic and sensitive structures with generally lower tolerance to settlement than is typically feasible with conventional pit underpinning. Robust, real-time geotechnical instrumentation monitoring systems have helped reduce the uncertainty and further expand the feasibility of jet grout underpinning applications. When properly designed and constructed by qualified and experienced jet grouting contractors, the flexibility of soilcrete for design and construction may be utilized to overcome the many inherent challenges which complicate underpinning and earth retention systems. INTRODUCTION The construction of buildings and infrastructure in our increasingly dense urban spaces often requires excavations below the elevation of existing structures immediately adjacent to the proposed work. Where a proposed excavation system encroaches into an existing structure’s zone of influence, additional measures, such as the construction of an underpinning or excavation support system, are required to safely excavate and minimize the impacts on the adjacent structures. Jet grouting is one method of underpinning that offers significant commercial and technical advantages over many other techniques. Though it was first used to the United States in the 1980s and has grown in popularity elsewhere, jet grout underpinning remains underutilized domestically due to its perceived cost and risk premium. Jet grouting has significant technical advantages over other underpinning methods due to its applicability in a wide range of soil types and its flexibility of design and installation. The jet grouting process is capable of limiting the movement of foundations during construction and excavation to lower thresholds than most traditional underpinning methods (Droof, Furth, & Scarborough, 1995). Its use for underpinning historic and sensitive structures with lower settlement criteria provides additional evidence to its technical utility. Through thoughtful design, adequate planning, and experienced installation, jet grouting can be an appropriate underpinning solution that can provide significant cost and schedule savings.

Jan 1, 2019

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Robert Alperstein, Nidal AbiSaab, Joe Pastore

"This paper describes the design and construction aspects of the foundation support for a 57-story building currently under construction in lower Manhattan. The site is located near the East River with subsurface conditions consisting of about 40-ft [12.2-m] of unsuitable historic fill and soft plastic clay underlain by about 130-ft [39.6-m] of dense sand resting on bedrock. A mat foundation supported on unsuitable soils improved by jet grouting was selected for the project. Design concepts and selection of the engineering properties of the improved and natural foundation soils are discussed. The results of quality control testing and methods to verify design parameters during construction are presented.INTRODUCTIONNew York City (especially Manhattan) is known for its skyline of high rise structures. The geologic conditions in the New York Metropolitan Area influence the selection of foundations and feasibility of high rise construction as noted by Horvath (2013). These conditions include varying depth and quality of bedrock, multiple glacial events during the Pleistocene Epoch, and the effects of human modifications to the subsurface environment. Clusters of relatively taller buildings are generally located in Lower and Midtown Manhattan where sound crystalline bedrock is at relatively shallow depth beneath the ground surface and shallow foundations rest on the bedrock surface. In recent years the use of more costly high capacity driven piles or drilled caissons and deep basements has enabled the high skyline to spread to other areas."

Jan 1, 2016

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By Paul M. Schuman, Alessandro Bertero, Giuliana A. Zelada, Sharon G. Cranston

Many jet grouted columns were recently installed to create a jet grout-treated soil foundation for an earthen embankment used in a large shoreline stabilization project in the Mystic River in Charlestown, MA. A physical test program was used to determine whether the jet grouting parameters the Contractor selected would meet the design requirements given the local soil variability, including soft river sediments and organic soils. The presence of hydrocarbons encountered in the marine sediments during the test program caused concern that the design strength could not be achieved. The published literature discusses the environmental aspects of jet grouting with hydrocarbons. The literature did not include many studies of the effect on jet grout-treated soil strength for the types and concentration of hydrocarbons encountered on this project. The grout mix, air pressure, and number of passes of jet grouting were varied in a second field test program to determine jet grouting parameters needed to achieve the design strength of columns with hydrocarbons. A geo-probe study was performed to identify the type and concentration of hydrocarbons on the site. With few exceptions, the quality control core samples from the production columns met the design requirements with many strength values far exceeding the design strength. This paper presents the data, and reviews the lessons learned. PROJECT BACKGROUND The Charlestown Bus Garage, located in Cambridge, Massachusetts, is a Massachusetts Bay Transportation Authority (MBTA) bus maintenance facility located on the Mystic River. The site was home to a coal gasification facility before it was developed by the MBTA as a bus garage in 1978. A deadman-anchored steel sheet pile bulkhead wall installed along the Mystic river on the east side of the site supports the site grade at about El. 11 ft (NAVD 1988) (Figure 1).

Jan 1, 2019

By G Lane, M Bueno

In a recent publication (Bueno and Lane, 2011) the authors presented the analysis of a consolidated dataset composed by 137 autogenous/semi-autogenous grinding (AG/SAG) mill pilot trials. By comparing the measured data against theoretical specific energy consumption, the analysis indicated which circuit configurations were more or less energy efficient. However, the analysis has also indicated that the energy efficiency of each of the types of circuits vary significantly.There are numerous factors that contribute to the variations of energy efficiency of AG/SAG mill-based circuits, such as feed size distribution, recycle ratios and ore characteristics. In view of this, the present work accesses these factors individually and discusses what may lead a particular circuit configuration to be more or less efficient in terms of energy and costs.CITATION:Bueno, M and Lane, G, 2012. Key drivers of energy and cost efficiency in autogenous/semi-autogenous grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 113-118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

By Andreas Brandner, Karl Schoenherr-Strasse, I. B. Brandner, Dipl. Ing

"A world famous Wintersport resort in the Alpine planned to build a parking garage for more than 600 cars and busses situated between a torrent, a district road and the village.A nearly 200 m long building giving place for 6 parking levels and a maintenance level for busses and trucks is situated alongside a hill causing excavation height between 20 and 25 meters, which had to be secured. Due to restrictions – neighbours did not allow the client to drill anchors for retention – we designed a solution combining micropiles, strand anchors, shotcrete and nails as permanent earth retention not exceeding the space of 7 meters provided by the local street. Soil conditions were as challenging - reaching from backfill to moraine with boulders of more than 20 m³ volume – as the construction period of total 12 months for the whole project, which was opened mid of November 2015.The innovative solution outperformed the client´s project from the technical and commercial aspect and helped the contractor to save time and money.The design process with its difficulties as well as erection process is described in the following paper."

Jan 1, 2016

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By Matthew C. Janes, Mark C. Spence

"A former coal gasification site next to Rock Bay in Victoria, BC, Canada required a barrier to permit dewatering and excavation of the bay and surrounding property. The adjacent property owners had stringent requirements at the boundaries of their properties. Isherwood Geostructural Engineers designed a temporary steel sheet pile (SSP) water retention structure and excavation shoring system along the perimeter of the site. The project involved challenging geotechnical conditions in soft clay soils and a multi-faceted construction staging plan involving the diversion of two large storm water outfalls that drained into the bay. Despite a well-conceived design and construction plan, unexpected site conditions and delays led to significant changes in design and construction approach. Employment of the Observational Method and on-the-fly geotechnical investigation were instrumental in maintaining project momentum and schedule. The paper presents the geotechnical and geostructural design details and construction events as they transpired, highlighting the key issues, discussions and lessons learned.INTRODUCTIONFor over 100 years, the Rock Bay Site, in Victoria, British Columbia, Canada, had a legacy of contamination left behind from previous industrial activities. The site was the former location of a coal gasification plant that was in operation from 1862 to 1952. The site was also an infilling location for a nearby tannery and sawmill. The remediation of the Rock Bay Site involved the excavation and replacement of approximately 300,000 tonnes of contaminated soils on Transport Canada’s property. The project commenced in 2004 and has occurred over several phases on multiple properties. In the third and final phase of the project, a temporary steel sheet pile (SSP) excavation shoring system and ocean barrier wall – required to seal off the bay – was employed to enable disposal and replacement of approximately 90,000 tonnes of contaminated soils from the shoreline and base of the bay."

Jan 1, 2016

By Tai Luu, Maxim C. Schisler, Yaser Taheri

The Stevens Gateway Project is an expansion of the Stevens Institute campus overlooking the Hudson River in Hoboken, NJ. The plans call for 90,000 ft2 (8360 m2) of new classroom, research, and student life facilities in new, 4-story buildings. The excavations for the building footprints were bounded by city streets and existing buildings, including the historic Carnegie Laboratory of Engineering, built in 1902. Pit underpinning was originally specified for the Carnegie building. However, given the depth of cut, construction time required for the 13 ft (4.9 m) deep pits would be substantial. The geotechnical contractor retained for the support of excavation work therefore offered an innovative active soil nail wall design that would meet project requirements in a shorter timeframe. Unlike the passive soil nail systems common in the industry that are chiefly used for soil slope stabilization, active soil nail walls contain pre-stressed anchor components to resist soil movement and limit settlement of soil and structures being contained. In addition to a discussion of the overall design approach of the active soil nail wall system, this paper will include a detailed description of its constructability and effectiveness. This project’s use of a conventional slope stabilization technique for an unconventional purpose may have positive implications going forward. INTRODUCTION Stevens Institute of Technology is a private university in Hoboken, New Jersey that sits on the cliffs of the City of Hoboken overlooking the Hudson River and Manhattan Island to the east of the campus. In recent years, the university has executed numerous plans to expand and upgrade its campus academic, student life, and residential facilities. One such project is the Academic Gateway Complex. The plan adds 90,000 ft2 (8360 m2) of new classroom, research, and residential facilities while also enhancing community connections by building a park to serve as a green corridor for the city. The proposed construction took place on the north and south side of 6th Street between Hudson Street and River Street. The project included the demolition of an existing university building followed by the construction of two, 4-story buildings on the north and south property lots. The north and south buildings will be connected by a second floor bridge spanning 6th Street. The buildings each contain a full basement extending from the proposed ground floor at approximately El. 41ft (12.5 m) to the basement subgrade at El. 26 ft (7.9 m). Each building will be constructed on respective mat foundations. Figure 1 presents an overview of the project area.

Jan 1, 2019

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010