Search Documents

By Zong-Xian Zhang, Charlie C. Li

It has been observed that the rock debris of a strain burst event are often in the mode of tensile fracture. Seismic waves could create tensile fractures in the material nearby reflecting surfaces, such as at the boundary of the fracture zone and the rock surface of an underground space. The fractured rock could be ejected to the space when the seismic waves are powerful enough. The average ejection velocity of the ejected rock is a measure of the magnitude of a burst event. The ejection velocity is directly associated with the released energy from the seismic waves and with the strain energy stored in the rock prior to the burst. In some cases, the seismic wave induced tensile fracture and the energy conversion occur in successive moments during bursting. In this paper, tensile fracture caused by seismic waves is investigated through an 1D model. The relationship of the average ejection velocity of the ejected rock in a rockburst event is analytically established with the energy of the seismic waves and the strain energy stored in the rock.

Apr 26, 2022

By B. Simser, T. Butler, A. Hall

The longterm future of Glencores’ mining operations in the Sudbury basin area of Ontario, Canada likely depends on mining deposits at depths below two kilometres. To gain a better insight into the rockmass response to mining, a geological scouthole program has been implemented at Glencores’ Nickel Rim Deep and Onaping Depth Project to gain insight into rockmass conditions ahead of the devel-opment face. The scouthole program involves drilling long (up to 600 m) subhorizontal boreholes drilled ahead of the development end and collecting data about the rockmass conditions from various geophysi-cal and mechanical tools (in addition to conventional core logging). Once all data has been collected and the borehole is available, seismic sensors are installed up to 450 m down the hole as part of the micro-seismic monitoring program with the leading sensor always located ahead of the development end. The recorded seismic data is used to provide realtime insight into the rockmass response to mining. On May 20, 2017 a flurry of seismicity with a maximum moment magnitude (Mw) of 0.7 occurred causing damage to the ramp heading. Data from the microseismic monitoring system had indicated that conditions at the development end were changing prior to the rockburst. A back analysis of the scouthole data indicated a clear anomaly in the rockmass at the location of the rockburst. The scouthole data also provided sufficient information to suggest that once this anomalous zone was exited, mining conditions would improve. With the microseismic monitoring system providing realtime information from the rockmass, the area was re-habilitated and ramp development continued successfully. Details of the rehabilitation and adjustments to the ramp development are discussed. Some correlations between the scouthole data and recorded micro-seismicity are also presented.

Apr 26, 2022

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

By Stephanie Singarayer, Damodara Reddy Chinnasane, Mike Yao, Danielle Pelletier

Mining at Vale’s Creighton Mine has been active for nearly 120 years in Sudbury, Ontario, Canada. Being the deepest mine in the Sudbury region, mining induced seismicity is a common occurrence at Creighton Mine. Over the past five years, 26 large magnitude seismic events ranging from 2.5 Mn to 3.7 Mn (Nuttli) have occurred. Out of these large magnitude events, three 3.0+ Mn events occurred between April 2020 and January 2021. The majority of the 3.0+ Mn events are believed to be the fault-slip type that could be linked to the known major geological structures and/or long-term effect of mining over many years. The recent large magnitude events are believed to be triggered by high induced stresses while mining the first few stopes of a new lower horizon in the top-down centre out mining sequence.

Apr 26, 2022

By Christina Dahnér, Kristina Jonsson, Savka Dineva

The iron-ore underground Kiirunavaara mine (Sweden) has been seismically active since 2008. In 2021 the production is on levels 1079 and 1108 m, at the deepest. The seismic activity has changed in character over time with one step change in 2015 when the number of large (ML>2) seismic events increased, and another one when the mine experienced a seismic event with Mw 4.2 in 2020. In 2017, the mine evaluated Hydraulic Fracturing (HF) as a possible mitigation technique for larger seismic events and a one-hole trial was performed. The trial proved promising, and it was decided to go forward with a large-scale trial covering an entire production area in the mine. The large-scale trial consists of 25 fracturing holes, 50 – 100 m long, running along 500 m out of the ~4500 m long orebody and spanning between production levels 1108 m and 1252 m. The fracturing process continued for a year, resulting in ~38,000 seismic events with −3.3<ML<1.4. The breakdown pressure varied between fractures in the same hole as well as between holes in the same area. Average breakdown pressure per hole was between 12 MPa and 50 MPa. The seismic response to HF in 2021 varied greatly from hole to hole and between fractures in the same hole. The variation in response could be related to the geological conditions and the infrastructure, such as large caving ore passes. In this paper some details about the experiments and broad preliminary analysis of the effect of the HF by using seismic source parameters of the induced seismic events are presented: 1) Distribution of seismic activity, 2) the ‘equivalent’ magnitudes for each hole calculated from the cumulative seismic energy and seismic potency released during the fracturing, compared with the local geological conditions; 3) the predominant failure mechanism of the seismic events caused by HF was defined. A difference in the behaviour between larger and smaller events was noticed, as ML>0 events seem to be compression type failures and ML<0 events seem to be related to slip on pre-existing structures. No seismic events related to creation of a new fracture have been identified yet.

Apr 26, 2022

By Ehsan Moosavi, Kamyar Tolouei, Mehran Gholinejad

The literature defines rockbursts in slightly different ways based on their generation mechanisms, field phenomena, and degree of damage, but in a way that is almost consistent. Generally, a rockburst refers to seismic events that mainly happen in underground excavations, for purposes such as underground mining, road and railway tunnels, nuclear power, etc., and that are followed by the collapse and outburst of rocks. Long-term rockburst prediction can be abstracted as a classification problem mathematically, in which we can introduce deep learning to solve it. Further, using deep learning in rockburst prediction can overcome drawbacks such as subjectivity and inconsistency brought from previous traditional approaches. A rockburst data-set, was employed to evaluate the current method for predicting rockburst grade, and the good results of overall success rate were obtained. The results indicated that the proposed algorithms can speed up parameter optimization search, the proposed method is robust model and might hold a high potential to become a useful tool in rockburst prediction research.

Apr 26, 2022

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Boyd Wise

A jet pump injector was developed and successfully tested, thereby demonstrating the feasibility of a jet injector for introducing coarse coal into an operating slurry face haulage system: In Phase I a variety of injection concepts were evaluated, and the jet pump was identified as best, due to its simplicity, compactness and performance potential. In Phase IIA subscale jet pump injector tests were conducted, and a computer model of a jet pump injector was developed whose performance predictions correlated well with subscale test results. In Phase IIB various system configurations were defined for integrating a jet pump injector into a fully operational underground coarse slurry face haulage system, further highlighting the feasibility and practicality of such a system. In Phase III a full-scale mobile haulage vehicle embodying a jet pump injector and coal sizing equipment was detail designed into a practical vehicle with attractive performance characteristics. More importantly, fully operational full scale jet pump injector -and feeder/breaker subassemblies were tested and proven successful in their ability to down-size coal to 3" in all 3 dimensions and to consistantly provide slurry of 4217 weight concentration at 6.4 TPM throughput under a wide range of operating conditions including zero to maximum feed rate within 5 seconds.

Jan 1, 1985

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By Ping Zhang, Shahram Mozaffari, Andreas Ylmefors

The risk associated with mining induced seismicity and the related rock bursts has become one of the major threats to the safety and sustainability of mining at the Kiirunavaara mine. The causes of mining induced seismicity at the Kiirunavaara mine are very complex and have affected our understanding on the source mechanisms of seismicity and further the mitigation of the seismic risk. Detailed analysis of historical mining induced seismicity at the Kiirunavaara mine was conducted. The focus of this analysis was placed on the classification of large seismic events and the evaluation of the influential factors on the classified seismic events. 145 events with local magnitude larger than 1.5 that occurred between January 1, 2011 and March 31, 2021 were analyzed. For this analysis, seismic events located in the hanging wall were not included, as these have not been observed to cause large damages to the mine itself. It was found that the magnitude of the events had good correlation with the stress change in relation to the production location. The seismic events were classified as mining-front associated, ore-pass associated, mining-front and ore-pass associated and others, according to their hypocenter location. Most of the mining-front associated events, concentrated around the production levels and slightly above and below them, generally correlated with shear cracks, and most of them occurred when the ore flow between two production levels started. The numerical modelling showed that slip of the geological discontinuity, due to unclamping between hanging wall and footwall, could be the major causative mechanisms, which further supports this finding. The ore-pass associated events are located close to the ore passes. Large seismic events located between ore passes have the source mechanism of both fault-slip and non-shear, but events located at the outer side of ore passes were all fault-slip type. By checking with the ore pass scanning data, it was concluded that the most of the events located between ore passes could be pillar bursts. An elastic core concept has been then used to define a critical pillar width. The paper is not intended to be prescriptive but rather to initiate discussion of the possible classification of seismic events at the Kiirunavaara mine and to present new perspectives of the causes of the seismicity for improving the present seismic risk management.

Apr 26, 2022

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By Peter Zhang, Mark Van Dyke, Ted Klemetti, Morgan Sears

Room-and-pillar mining is a mining method used in the United States to extract coal from underground, and pillar recovery is widely practiced for maximizing coal recovery and mining economics. Under certain conditions, room-and-pillar mining can create high stresses in coal pillars resulting in a coal outburst. These outbursts represent one of the more severe safety hazards in underground coal mines, potentially causing injuries and fatalities. Over the past ten years, coal outbursts have resulted in three fatalities in U.S. room-and-pillar mines. Though coal outbursts generally occur under deep cover, they are more likely to occur during pillar recovery and under multiple-seam mining conditions. Coal outbursts are generally associated with strong roof and floor and heavy loading of coal pillars, but it is difficult to predict whether, where, and when they will occur. In this respect, risk management provides a proactive tool to prevent coal outbursts in room-and-pillar mining by identifying mining areas with high risk of outburst and mitigating the risk accordingly.

Apr 26, 2022

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By C. E. Johnson, R. L. Bauer, E. M. Johnson

In industry, the strength of a blasting cap is often equated to the type of explosive it can detonate. Comparable cap strength is becoming less important as nearly all caps manufactured today can initiate high explosives, such as primasheet, with ease. Previous studies were conducted to assess the quantity of energy released by various detonators into the directional propulsion of the detonator’s casing. However, the question of how much of this propulsion energy is needed to initiate an explosive remains unanswered. This study will assess the fragmentation size and velocity needed to initiate a high explosive when they are not in direct contact. For this study, primasheet was used as the main charge as it is relatively insensitive and can be situated in different positions relative to the detonator. Electric, non-electric and electronic detonators were used to evaluate initiation potential. The primasheet is observed in response to being in contact with a detonator, and not in contact with the detonator at various distances and angles. This allowed the quantity of energy transferred into the primasheet to be observed and for the initiation of the sheet to be recorded using high-speed video. This study will report the energy necessary to initiate the primasheet at various distances and angles from the charge from a number of widely used, commercial, hot wire blasting caps.

Feb 6, 2023

By L. E. Jackson, E. W. Dean

One of the refining processes to which lubricating oils are frequently subjected effects a reduction in content of paraffin wax. The actual treatment usually involves chilling and filter pressing; the most important result accomplished from a commercial point of view is lowering of the ""cold test"" of the oil. The Bureau of Mines has recently had occasion to ascertain the effect of changes in paraffin wax content upon the viscosity of oil and has conducted a series of experiments described in the present report.Object of the present investigation:The Bureau of Mines has devised and is using a method for the analysis of crude petroleum* which includes determination of the viscosities of lubricating oil distillates. The Bureau method does not provide for preliminary removal of paraffin wax, and it has seemed advisable to determine whether this omission causes any important variation from the results that would be obtained through commercial refinery processing. It was also thought that the present tests, though limited in scope, might be of some practical value in indicating the general effect of paraffin content upon one of the most important properties of lubricating oil.Experimental procedureA five-gallon sample of Pennsylvania crude petroleum was distilled at atmospheric pressure until 50 per cent of the charge had been vaporized. Two liters of the residuum was distilled at a reduced pressure of 40 mm. (absolute) and cuts were separated that came over between the temperature limits of 250° to 275° C. (462° to 527° F.) and 275° to 300° C. (527° to 572° F.). The viscosities of these fractions were determined and they were subsequently subjected to treatment that removed successive percentages of paraffin wax. Viscosity temperature curves were determined for the oil obtained after each removal of wax.

May 1, 1921

By Milind Deo, Neale R. Neelameggham

The mixture of carbon dioxide and water vapor - called Soda [as in carbonated water] can be converted to easily stored transportation fuels. Earlier papers on Soda- fuel metallurgy noted that this conversion is endothermic requiring energy. Reduced state metallic elements - preferably the alkali, alkaline earth elements, or aluminum can act as oxygen carriers. Availability of such a combination in commonly land fille waste materials is shown. Plant based wastes which are normally composted form a better-controlled reagent. The energy required for the reaction can come from solar energy. This paper describes possible reactor designs, which can accommodate this conversion effectively using carbon dioxide recovered from flue gases.

Jan 1, 2008