Search Documents

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By V Poizat

In different parts of the world the term epithermal is commonly used for a variety of deposit styles. Using the redox state of the ore-forming fluid (inferred from mineralogy and alteration), the metal assemblage of deposits, and other characteristics, at least five different styles of epithermal deposit can be distinguished. Most of these different deposit styles appear to be related to magmatic fluids, with differences resulting from different compositions of source magmas. The most common style of epithermal deposit (low-sulfidation gold-silver deposits associated with calc-alkaline volcanic rocks) remains the most difficult to explain; the metals in these deposits may be derived by basement leaching without magmatic input, or they may come from magmatic volatiles, with contaminated I-type or S-type magmas as the most likely source.

Jan 1, 1995

By J. G. Savins

Analytical procedures are described for optimizing the selection of a rheological model when it is desired to express the functional relationship between true shearrate and shearing stress in analytical form. The procedures are extended to two principal model categories — "Generalized Newtonian" and "Viscoplastic" models. Graphical examples are presented to illustrate the utility of certain characteristic deriuative functions in distinguishing between these categories and in determining how well a particular model reflects the flow behavior of rheologically anomalous materials in simple shearing flows. INTRODUCTION Modern drilling fluids and fracturing fluids, being chemically complex, are frequently non-Newtonian — a peculiarity which complicates the solution of problems such as designing flowline and process equipment, and predicting laminar-turbulent behavior, solid-suspending ability and cutting-transport efficiency. Therefore, techniques of data analysis which accurately characterize the behavior of rheologically complex materials are needed for the accurate formulation of solutions of these and similar problems. It is the purpose of this paper to describe the application of a sensitive method of rheological data analysis — the dual differentiation-integration method of optimizing the selection of the functional relation between shear rate and shearing stress — to a variety of materials of interest in drilling and production practices. BASIC CONCEPTS THE DIFFERENTIATION METHOD To a first approximation, the viscosity function for a non-Newtonian system can be expressed in a form analogous to Newton's law of viscosity by the following generalization2.3 between the stress On introducing the restrictions that the system is incompressible and the motion is rectilinear, then l = 0 and l3 = 0 ; and with the further restriction that the flow is slip-free, the viscosity (an invariant) is then determined solely by 12. With this approach one can set up a suite of integral equations relating observed kinematical and dynamical parameters for certain types of flow experiments involving simple shearing motion, e.g., flow in a cylindrical tube, flow between rotating concentric cylinders, and flow between fixed parallel surfaces of large aspect ratio. Taken in the order cited, these integral equations are as follows.

By Oberlin Smith

It may surprise the learned metallurgists who read this paper to learn that, by a recent discovery, nails of good quality can be made at one operation, directly from the ore, at the rate of, say, sixty per minute for each operator. It should be stated, however, that the raw material referred to does not answer strictly the ordinary assayer's definition of' an ore. It is found, in strata of various thickness, in Harlem, N. Y., and other localities where the débris from restaurants and from sheet-metal factories of various kinds has been dumped. In other words, it is old and new tin-scrap—one of the few substances which this generation, mainly occupied in exhausting the accumulated resources of the past, seems to have laid up, by way of atonement, for the benefit of posterity. In speaking of this material as ore, we are simply looking forward, prophetically, to the time when our descendants may dig it. up and write learned papers for the American Institute of Mining Engineers upon the best methods of assaying and smelting it. At least such has seemed to be its destiny hitherto. It may fairly be said that the many attempts which have been made to utilize it by separating, through chemical or electrolytical processes, its two valuable constituents, metallic tin and first-class wroughtiron, have failed, either technicaljy or commercially. The reasons fur such failure need not here be discussed: Either the separation has been incomplete, the iron still retaining enough tin to spoil it for the sinking-fire, or other use short of re-melting (perhaps even for that), or the manipulations of the process have been too expensive to make its results profitable—or both. Meanwhile the great tin-scrap deposits have gone on growing faster than any other strata of our Post-Tertiary, Psychical Era; given up by metallurgists, not yet attacked by geologists, and explored only by that mining engineer of the transitional period, Gulielmus Caper. Before leaving these heaps of tin-scrap, however, to become mere mineral deposits for future ages, it may be well to consider a novel plan for their immediate utilization—novel, not only in its means, but in its principle. For it undertakes to use this material just as it is, without trying to separate its constituents at all, and to use it,

Jan 1, 1889

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;' this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.' Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.' The effect of stress on M, (2°C per kg mm-') was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-'. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). 'A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. 'C. Crussard: Comptes Rendus (1953) 237, p. 1709. ' G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By Gustaf Ising

For relative gravity measurements, the author in 1918 described an instrument1 of which the essential part consists of a highly astatized, standing pendulum turning about a horizontal elastic axis. This type of instrument has been used recently in practical field work, therefore a description of its principle and technical development is given herein. Part I, describing the principle, is a direct translation of the original Swedish paper.l Part II gives an account of the practical elaboration of the instrument, together with some description of measurements performed. I. Principle of Using Astatized Pendulums1 In order to reduce the trouble and waste of time attending the use of ordinary pendulums in measuring the force of gravity, various instruments of another type have been suggested for relative determinations, as a rule arranged in such a way that the attraction of the earth on a certain body or mass of fluid is balanced by elastic force from a spring or a shut-in mass of gas. A change in the force of gravity is then made manifest as a change in the position of equilibrium of the body, in that the deformation of the spring (or compression of the gas) is changed. With such instruments there are, however, great difficulties in keeping the elastic force constant or its variation known with sufficient exactitude, because of elastic after-working, influence of temperature, and so on. The author suggests for relative determinations of gravity another type of instrument, in which two directional forces (control coefficients) rather than two forces are compared with one another. By "directional force" or "control coefficient" is meant that quantity in a rotatable system that, multiplied by the angle of deflection, indicates the moment counteracting the deflection. In this way it will be possible greatly to reduce the influence of the elastic after-working, which in instruments with spring devices acts so disturbingly. The instrument is made with a rotatable system arranged in such a way that the total control coefficient acting upon it, is composed

Jan 1, 1940

By V Rodríguez, M Hormaza, R J. Romañach, C Pinzón-de la Rosa

The authors have presented their ideas for developing a powder sampling device in the I-Corps™ program sponsored by the National Science Foundation (NSF). This is an intensive customer discovery program developed to increase the economic impact of the research sponsored by NSF.The I-Corps™ program requires performing at least 100 interviews with potential customers in various industries. These interviews are essential to establish the need for a particular product or solution, and identify potential commercialisation partners and competition. The interviews have revealed the absence of Theory of Sampling (TOS) principles in many companies. The interviews are designed to identify the difficulties associated with current sampling practices that do not meet TOS principles.The I-Corps™ program is a significant challenge for scientists who often avoid discussing a concept in fear of losing their research idea. The program teaches how to obtain information without releasing the important intellectual property related to a product development idea. The I-Corps™ methods have been used to discover the prevailing ideas on sampling in various industries.I-Corps™ also teaches how to present ideas to investors; another significant challenge for a scientist. We are currently learning to present sampling and TOS to investors and business development experts, and will share some of these experiences.CITATION:Pinzón-de la Rosa, C, Rodríguez, V, Hormaza, M and Romañach, R J, 2017. Theory of Sampling meets the National Science Foundation I-Corps™ program, in Proceedings Eighth World Conference on Sampling and Blending , pp 351–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

THE annual meeting of the Lake Superior Mining Institute was held on Sept. 7 and 8, Crystal Falls and Iron Mountain, Mich., being the principal centers of activity. Members of both institutes began assembling early, and by the evening of Sept. 6, some 60 had already arrived at Crystal Falls. The greater number arrived the following morning, however, and after the usual formalities of registration were attended to, the party were loaded into automobiles and set out on a tour of inspection of the mines near Iron River; some properties were passed through, and some were briefly visited to permit the inspection of any unusually interesting piece of equipment or detail of practice. The last stop of the morning was at the Caspian, Iron River, where the entire party was entertained at luncheon at the Caspian Club House. Both the food and the company were excellent, and as the weather was superlatively good (though the natives of the district modestly declared it was only ordinary autumn weather) the lunch was served on the lawn at the rear of the club, where the green turf, abundant flowers, and music by the band, added to the charm of good fellowship. The degree to which mining men have become addicted to golf was indicated by the large number of plus fours in evidence, whose wearers appeared just before lunch and disappeared immediately afterward.

Jan 1, 1928

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

By W. Z. Rogers

U.S. feldspar output sold or used in 2004 was estimated to be 790 kt (871,000 st), valued at $43 million free-on-board plant. This was below 2003 and about the same volume as 2002. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures, and fiberglass insulation requiring feldspar and shipments of glass containers increased by about 4 percent. Imports of ceramic tiles and plumbing fixtures continue to increase, taking the place of U.S. produced goods, and the feldspar required to make them. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite.

Jan 1, 2005

By William L. Payne, Edward E. Ives

A unique feature of Potash Co. of America&apos;s A new potash property near Saskatoon, Sask., is the use of semi-dome-shaped buildings for product storage. Four domed structures, timber-framed and corrugated-sheet covered, are being built; each designed to handle 20,000 cu yd. The relatively small capacity units, PCA believes, give flexibility not only in storing different grades and sizes of product, but also in permitting greater ease in shipping products as market demands change. The domed buildings are 150-ft diam, comprised of a 16-ft-high concrete wall base, topped with a metal sheet-covered octagonal timber frame. The dome of each unit is designed to fit very closely the angle of repose of the contained material, which results in the maximum usable volume. The entire roof is flood coated with a bitumin to provide a complete weather seal.

Jan 9, 1959

THERE are two general types of scientific approach to a problem. One approach, which is the more widely known, involves an analysis of the situation at the beginning of the experiment; this is followed by an analysis of the situation at each instant of time during the experiment and leads to a-detailed description of the prevailing conditions at the end of the experiment. Suppose, for example, we wish to predict the final rest position on a billiard table of a ball moving initially in a certain known direction with a known speed. The obvious approach is to estimate or measure off its course by consideration of angles of rebound, taking account of the "English" or spin if necessary and finally estimating from experience (or calculating from coefficients of friction) the slowing down occasioned by friction, thus establishing the point of the course at which the ball may be expected to stop. Any interference with the calculated course occasioned by collision with an unanticipated object would obviously cause us to revise drastically our estimate of the rest position. This general method of approach characterized by detailed description of how one situation developed from another seems intuitively appealing and is the most widely known method. There is no doubt that it gives very satisfying results when it can be used. There is a second general method of approach. In this method, the final state of a system is predicted from knowledge of general broad principles and their application, considering only the restrictions imposed upon the system. It is unnecessary to follow the course in detail; intermediate steps are not even considered. For example, if the billiard table mentioned in the first paragraph were tilted to one corner, one could predict that the final resting place of the ball would be in that corner; this prediction can be made independent of any particular course the ball may follow. This second general method of attacking problems is the one used in thermodynamics. There its use is so outstand-

Jan 1, 1951

By A Mackay

As a result of the explosion in the 512 panel at the Moura No 2 mine in 1994 the role of the ventilation officer (VO) to submit sealing plans (on behalf of the operator/underground mine manager) has become one of the key duties of the VO of an underground coal mine in Australia. The intent of a sealing plan is to document the controls used to manage the build up of flammable concentrations of gases, and for these controls to be reviewed by the industry regulators. These sealing plans have brought a large amount of focus onto the sealing process and served the industry well. The legislation does not define sealing, or when it begins, but throughout the industry typically sealing plans are submitted 30 days prior to the last seal being constructed. This practice appears to have originated from the Moura 512 panel being a standing bord and pillar panel and where the explosive gas mixture could only occur after it was sealed. However, since the Moura disaster the industry has become dominated by goafing style longwall mining. Goafing panels differ from standing bord and pillar panels in that they typically have an unventilated goaf that can potentially contain an explosive mixture from start-up. This was recently highlighted by the explosion and fire on Longwall No 1 Tailgate at the Blakefield South Mine in 2011. The author ponders whether the industry should revisit sealing plans to focus on the core hazard and define that sealing begins when flammable concentrations of gases are created. Although defining when mine sealing begins is the key outcome of this paper, the main point is that VOs and industry regulators need to clearly understand what can occur in the atmosphere of underground coal mines. CITATION:Mackay, A, 2013. A case for change - Defining mine sealing and understanding flammable mixtures during sealing, in Proceedings The Australian Mine Ventilation Conference , pp 307-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By G. P. Conard, E. H. Rennhack

The creep behavior of hot-rolled, hypoeutectic Zn-Ti alloys was investigated in the temperature range from 0.43 to 0.53 TM. Secondary flow was found to originate primarily from strain-induced gvain growth where grain boundary )nigvation served to relieve the strain energy of distortion introduced by slip, grain boundary sliding, and subgvain formation. The extent to which this recovery mechanism operated was determined by the ratio of grain width to the spacing between planar fibers of TiZn,, compound particles generated in these alloys during rolling. When this ratio was unity, creep resistance demonstrated a marked improvement. In this condition, which was fulfilled by annealing following rolling, structural stability was enhanced with decreasing grain size below the equicohesive temperature (-0.5Tm), while the reverse was true above this temperature. TITANIUM concentrations approaching the eutectic composition of 0.23 wt pctl have been shown to promote a significant increase in the creep resistance of rolled zinc,2 The alloying effect created with titanium is somewhat unique; a structure closely resembling that of a fiber-reinforced metal composite can be developed which selectively modifies creep strength in preference to other mechanical properties. In an earlier investigation,~ the present authors found that, while the fiber network, composed of individual TiZn,, compound particles, had a distinct influence on rolled texture, the crystallographic variations produced were of minor importance with respect to creep. Rather, creep resistance seemingly increased when the grain size appeared to coincide with the in-terfiber spacing. The work described here was undertaken to explore this effect in greater detail. EXPERIMENTAL PROCEDURE Three zinc-base alloys containing 0.05, 0.12, and 0.16 wt pct Ti were prepared from CP zinc and iodide titanium in the form of 4 by 2 by f in. chill-cast ingots. The melting and casting procedures for these alloys have been detailed el~ewhere.~ Individual ingots of each alloy were hot-rolled at 200°C (392°F) to total reductions of 10, 25, 50, 75, and 90 pct in from one to five passes, respectively, employing a 10-min reheat prior to each rolling pass. With grain, tensile-type creep specimens with a 1-in.-long, -in.-wide gage section were machined from the rolled strips for test purposes. Annealing studies to explore the influence of grain size on secondary creep flow were carried out at 400°C (752°F) in argon for times extending up to 60 min. The grain-size effect was evaluated in terms of average grain width and length values statistically derived from lineal intersection measurements.4 A similar method was applied in establishing the average interfiber spacing, i.e., average perpendicular distance between adjacent planar fibers. The creep characteristics of the alloys were investigated by means of constant-load and constant-stress creep tests. The former tests were conducted at 25°C (77°F) under an initial stress of 10,000 psi, while the latter were performed in the range from 25°C (77°F) to 90°C (194°F) at stress levels varying from 8000 to 22,000 psi. Total specimen strain, as determined with Budd HE-1161-B strain gages, was in excess of 0.10. Maintenance of constant stress was achieved through periodic load reductions made at 0.01 strain intervals to compensate for the attendant incremental reduction in specimen cross-sectional area. The maximum indicated error in the applied stress at these strain intervals was less than 3.0 pct. RESULTS AND DISCUSSION Constant-Load Creep. In an effort to clarify the in-terrelation between interfiber spacing and grain size with respect to the creep resistance of the Zn-Ti alloys, their separate effects on secondary creep rate were determined as a function of titanium content and rolling reduction. These results are set forth in Figs. 1 and 2, respectively. The average grain diameter plotted in Fig. 2 was resolved from average grain width and length values. No data are presented for reductions of less than 50 pct because of the inability to obtain consistent measurements on these strips. The curves of Fig. 1 indicated that, for a given titanium content, a decrease in interfiber spacing, as produced with increasing reduction, promoted a decrease in creep rate. Depending on titanium content, however, wide variations in creep rate occurred at the same interfiber spacing suggesting that interfiber spacing, by itself, has little or no influence on creep resistance. Grain size, on the other hand, decreased progressively with both increasing rolling reduction and titanium content, the effect of which led to a pronounced decrease in creep rate, particularly when the average grain diameter became smaller than 3.0 x 10"4 in., Fig. 2. The continuity of this relationship tended to support the view that grain size rather than interfiber spacing was predominant in controlling secondary creep. Annealing Effect. The observed dependence of creep flow on grain size suggested that a further contribution to creep resistance would result when the alloys were annealed to effect a coincidence between grain width and interfiber spacing, see Fig. 3(b). ~eiides creating an immediate barrier to grain boundary movement, annealing offered the possibility of providing increased structural stability by eliminating many high-energy, mobile grain boundaries.= To test this hypothesis, specimens from the Zn-0.16 Ti strips reduced 75 and

Jan 1, 1967

The regular activities of the Institute are financed mainly by income derived from members&apos; dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the amount of these endowments totals more than $637,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which Henry Krumb is Chairman, and of which the other members are: George D. Barron, Cleveland E. Dodge, John V. N. Dorr, Howard N. Eavenson, D. C. tackling, Harvey S. Mudd, Wallace E. Pratt, Milnor Roberts, and Wilfred Sykes. This committee believes that there exists a tremendous opportunity for the Institute to be of evergrowing service to the public, to the mineral industries, and to the &apos;profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light.

Jan 1, 1946

By G. D. Van, Arsdale

IT IS particularly appropriate that a paper on this subject should be presented in Spanish, before a Spanish speaking audience, and in a South American country, first because of the facts that these countries today have not only the largest copper leaching plant in existence but also present great opportunities for future extension of hydrometallurgy; and second, because of the fact that the first copper made by any wet method was doubtless produced before existing records at the Rio Tinto deposits in present day Spain.

Jan 1, 1925

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By Ward C. W

Conventional polygonal and block modelling techniques inadequately represent the grade-thickness distribution of some narrow shear and stratabound gold deposits. The polygonal influence of high-grade drill intercepts can result in overestimates of resource tonnages at high-grade cut-offs. Although block modelling methods provide grade smoothing and a better representation of structural continuity, the technique can lack precise definition of ore width. An alternative method known as Spatial Object Modelling (SOM) has been developed on MineMap software to overcome some of these modelling issues. This method does not rely on a uniform cell size and allows grade smoothing between resource intercepts in three-dimensional space. The SOM technique creates grade-thickness bars on regular, user-defined spacings which allow easy visual comparison of raw intercept data to the interpolated model. Model cell values are readily transformed into isopachs, isopleths and resource perimeters for reporting and mine planning purposes.

Jan 1, 1997

By N. Hosking, M. Nichols

Aluminum alloys are increasingly used for automotive body construction but are susceptible to filiform corrosion or paint blistering in service. Filiform corrosion resistance of two 6000-series aluminum alloys was investigated in this work. Test panels were produced with full automotive coating layers and scribed parallel and perpendicular to the rolling direction. The corrosion exposure comprised an inoculation step with acidified salt solution followed by a 6-week exposure period at 95% relative humidity and either 25°C or 70°C. Greatest corrosion activity was measured on the alloy with higher copper content, AA6111. Higher temperature exposure led to greatly enhanced corrosion activity for AA6111 compared to the lower temperature exposure. The 70°C exposure also led to greater mean corrosion-affected area measurements for the low copper aluminum alloy, AA6022, but the effect was not as stark as that observed for AA6111. Rolling direction affected the propagation direction, and possibly mechanism, of the corrosion effects. Cross-sectional analysis revealed dense corrosion products within the filament, comprising mostly aluminum and oxygen but with traces of chloride and sulphate. Development of varying filament and blister types on a single test panel and the progression of corrosion underneath a filament into the substrate indicate that several corrosion mechanisms can develop on the test panel, testament to the complexity of the corroding surface developed on an aluminum automotive body panel.

Jan 1, 2015

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Galis Mfg. Co. roof drill. The instructions are based upon two actual installations: one made in a mine on roof drill, model 300, and one in the factory. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other roof drills with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other roof drills and can determine any necessary modifications if they are not.

Jan 1, 1973