Search Documents

By D. J. Duck

INTRODUCTION Construction of the 3,600,000 kilowatt Third Powerplant at Grand Coulee Dam started in late summer 1967 approximately one year after authorization by Congress. The project was made possible by a treaty with Canada providing for cooperative development of the Columbia River which was signed in 1961 and ratified in 1964. Description of the Work The existing Grand Coulee power complex consisted of a dam and two powerplants with a switchyard serving each plant, one on each bank of the river. See Fig. 1. The switching facilities were connected to transformers at the powerplants by overhead 230-kilovolt and 115-kilovolt tie circuit conductors. [ ]

Jan 1, 1997

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina's first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller's earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller's earth, kaolin and vermiculite

Jan 1, 1977

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By M. A. Mahtab, N. M. Cruickshank, M. T. Wane

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment, and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) microseismic activity. Geophysical and engineering methods for detecting these characteristics are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1987

By Guillermo Velarde F.

El presente trabajo describe el proceso de la conductividad como herramienta de manejo de la aglomeración y la lixiviación en las pilas. En este sentido, dicha conductividad es un recurso necesario de manejo que garantiza la calidad de producto según los requerimientos hidrometalúrgicos. Para ello, se realizó un periodo de aplicación en la S.M. Cerro Verde, cual permitió eliminar las consecuencias de la deficiente aglomeración de entonces. De forma que el criterio de control operativo para el manejo de la aglomeración es mantener el valor de conductividad eléctrica del aglomerado en el rango de 150-180 mA,- aplicable al mineral muy alto o muy bajo en finos o arcillas- y el que garantiza un estándar y deseable calidad, sin segregación en las pilas, etc. En consecuencia, las operaciones mineras con mayores problemas en la permeabilidad de sus pilas por finos o arcillas en calidad indeseable, encuentran bajo este desarrollo, la solución para mejorar su aglomeración, así como el conocer la permeabilidad que tendrá la pila en emplazamiento, se pueda realizar las medidas correctivas.

Jul 31, 2003

By L. Zeng, Q. Feng, Z. Qiu, L. Ou, Central South University

It is well-known that the use of nanobubbles can significantly improve the flotation efficiency of ultra-fine particles. However, this is mainly focused on coal and phosphate rock flotation. In the field of nonferrous metal processing, the related research is few. In this paper, a small laboratory mechanical cell associated with a specially-designed nanobubbles generator was used to investigate the effects of nanobubbles on enhancing ultra-fine scheelite flotation. Nanobubbles were created and based on the hydrodynamic cavitation principle through Venturi tubes. Comparative flotation tests were performed using different tubes to evaluate the nanobubbles impact on the ultra-fine scheelite particle flotation recovery. In order to better understand the nanobubbles enhanced ultra-fine scheelite flotation, nanobubbles potential and size distribution were measured. The effect of nanobubbles on the particle aggregation and scheelite particles potential were also studied through the turbidity tests, microscope tests and zeta potential measurements. According to the results, the mean size of nanobubbles was about several hundred nanometers, and the surface of nanobubbles was of highly negative charge in alkaline conditions. The flotation recovery of ultra-fine scheelite particles was increased in the presence of nanobubbles. The zeta potential measurements indicated that the repulsive forces between scheelite particles decreased when nanobubbles existed. Through the turbidity tests and microscope tests, the promotion effect of nanobubbles on particle coagulation could be verified more directly. The existence of nanobubbles in flotation system promotes the particle aggregation, thus increasing particles apparent size and particles capture by bubbles, which may be the fundamental reason why nanobubbles enhance ultra-fine scheelite flotation.

Jan 1, 2016

By R. L. Loofbourow, Roger V. Pierce

THE degree to which our mineral requirements are being met by mining leaner, more complex or more remote deposits is indicated by developments during 1953. Heavy capital investment, skilled technical advice, planning, and able execution are requirements for the typical venture. Producers, faced with rising costs and with softer prices, are seeking improved mining and recovery. Developments in production of iron ore are typical of the course being followed in metal and nonmetal mining. Iron ore development in the U. S. is concentrated on the spectacular work with Lake Superior taconite, while in Canada new production is expected from Labrador and output from Steep Rock, Algoma, and Newfoundland is being increased. Shipment of iron will soon be made from Venezuela.

Jan 2, 1954

By Martins V, Dunne R

A re-evaluation of the Hampton Boulder prospect in the early eighties resulted in a decision to proceed with mine development in December 1985. A 500 000 tpa gold treatment plant was commissioned in December 1986. The treatment facility was expanded to 1 600 000 tpa in July 1988. A tailings treatment plant to improve recoveries from harder gold bearing sulphide ores was built in December 1990. The development of an underground mine in 1991 meant that a source of sand for backfill was required. A sands plant to fulfil this requirement was commissioned during November 1991.As of June 1992 a total of 7 710 487 tonnes of ore have been treated through the New Celebration gold plant. Total gold production from inception of the new mine until June 1992 is 545 470 ounces obtained at an average recovery of 90.1 per cent from an average gold head grade of 2.4 g/t. The combined quoted ore reserves at the end of December 1991 was 14Mt grading 1.8 g/t gold

Jan 1, 1992

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

Arkansas Geological Survey, Rooms 443-447 State Capitol, Little Rock, Ark George C Branner, State Geologist A list of available publications will be sent upon request Publications issued by the U. S Bureau of Mines, U S Geological Survey and Oklahoma Geological Survey, pertaining to' Arkansas, are also available through this Survey office. Annual Reports may be had for the following years. 1890, 3147, 1891, 81 35; 1892, $1 10 Other available publications: The slates of Arkansas, by A H. Purdue, with a bibliography of the geology of Arkansas by John C Branner (1909), $1.10, Coal mining in Arkansas, pt 1, by A A Steel (1910), 3175, An outline of the physical features of Arkansas, by George C Branner (1927), free, An outline of the metallic minerals of Arkansas, by George C Branner, free, Bulletin 3, The geology of the Arkansas Paleozoic Area, by Carey Croneis (1930), $3 20, Bulletin 4, St Peter and older Ordovician sandstones of northern Arkansas, by A W Giles (1930), $1 95, Bulletin 5, A geomagnetic survey of the bauxite region of Arkansas, by Noel H Stearn (1930), 80 cents, Information Circular 1, A barite deposit in Hot Spring County, by B Parks and George C Branner (1932), $1, Information Circular 2,

Jan 1, 1933

By Keith G. Wallace, Robert Wise, Ian J. Duckworth

This paper describes a case study for the ventilation planning at Utah Fuel Company's Skyline Mines which are located outside Price. Utah. The Skyline Mines are currently comprised of two longwall coal mining blocks located in two different mines. A third replacement longwall block is currently being developed. Future ventilation systems for the mines were determined by establishing ventilation models developed from data collected during a detailed ventilation survey. The paper discusses the challenge to coordinate immediate ventilation requirements with long-term demands. The continuous movement of the longwall, which frequently represented the only open split in the ventilation network, resulted in cyclic ventilation demands dependent upon the length of the tailgate. A series of system configuration changes were recommended based on the results of the network modeling exercise and an economic evaluation of the various options. The scope and cost of the configuration changes, and the mead improvement resulting from these changes is discussed.

Jan 1, 1995

By Kal V. S. Sastry

Modeling and simulation are two major tools available to a mineral process engineer for a consistent and systematic process analysis. The application of these tools to the analysis of specific mineral processing unit operations is well documented in the literature; nevertheless, they are used only to a limited extent in the industry. This is because the fundamental principles of modeling and simulation in the context of mineral processing context are not available. This paper represents the first in a series of papers planned to meet this need. General principles of process modeling and a unified mineral process model development methodology are presented. A simple example of model development using the flotation unit operation is given. A discussion of the practical significance, challenges and opportunities associated with mineral process modeling is included.

Jan 1, 1990

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Member, aged 34, married, technical graduate, 10 years' experience as mining engineer and mine superintendent, desires position. Can show low cost records and good references. No. 176.

Jan 1, 1916

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960's was done on coking coals.

Jan 1, 1981

By J. Y. Oldshue

INTRODUCTION The field of fluid mixing involves many different kinds of process objectives. In order to classify these objectives, Table 1 gives a listing of five basic application categories, gas-liquid, liquid-solid, liquid-liquid, miscible liquids, and fluid motion. However, each of these areas can be broken up into two different concepts one involved with uniformity of solids or liquids as a criteria, and the other involved with chemical reactions or mass transfer. The things that we would do to design a fluid mixing for solid suspension are quite different from things that we would do to design a mixer for heat transfer or gas-liquid mass transfer. Therefore, there are really ten separate mixing technologies. Each of these areas has its [ ] own principles of fluid mechanics, scale-up techniques and application experience. We will take a look at each of these areas and look at some of the ways that we can handle fluid mixing applications which.

Jan 1, 1979

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By P. R. A. Andrews, R. K. Collings

The beneficiation of barite has been the subject of many investigations at CANMET, thus reflecting barite's importance as an industrial mineral. Fifty-one studies relating to various aspects of beneficiation were conducted between 1920 and 1986, and a review of some of the more important studies is presented. The information, including mineralogy, beneficiation methods and results, flotation parameters, and reagent concentration data, is presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of barite ores from a variety of origins.

Jan 1, 1990

By H. D. Hagen, C. E. Nelson

14.1-1. Coal Mining. CORPORATE STRUCTURE. Most coal companies that operate surface mines had their beginnings as basically one-man organizations, with all decisions and controls in the hands of the founder. At the early stage of the company development, it is usually quite possible for one man to handle all management functions as the mining operations generally are quite localized and the founder can have a first-hand knowledge of all facets of the operation. However, with continued growth, the entrepreneur finds that he must limit himself more and more to the top level of management and delegate the day-to-day operation to others. An organization must be developed that provides not only for current operations but also for continued growth of the company through acquisition of coal reserves in market areas that the company desires to serve. In general, a successful coal company engaged in surface mining must develop an organization consisting of the following departments or divisions: operations, sales, engineering, exploration, land, purchasing, financial, and legal. Of course, all of these departments are not required in the beginning. When the company is small, there is much overlapping of functions. For instance, the operating department will handle purchases and the engineering department will also handle exploration and land functions. A growing surface-mining company has generally evolved through the various stages of development into an organization that is typical of large mining companies. An examination of a typical company and its various departments and their functions should give an insight into the organizational trends of surface mining companies. Having begun as a typical one-man organization, a company of today can be highly centralized, with firm control of all phases of the company's operations in the executive offices. This is achieved by having all department heads (Fig. 14.1-I), as well as the senior management, based in central offices.

Jan 1, 1968