Search Documents

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By A. E. Bellis, T. W. Hardy

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operatioqs. Hundreds of dollars are spent in the design and manufacture of milling cutters of special form for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring-the tool out "clean," is a difficult one and calls for no small amount of skill. In order to be on the safe side the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed stee1, in which metallographic means were used to determine the correct hardening tempcratures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accom- . panying table. Six specimens from the same bar of each kind of steel

Jan 1, 1917

If you are to be and remain competitive in the mining industry, it is vital that your company management systems are efficient. An integral part of today's competition in a ruthless market is to keep internal costs to a minimum. Integrating our core and parallel management systems is becoming an essential strategy to ensure efficiencies are maintained to the highest level, allowing the maximisation of profits, and to maintain that leadership status within our industry. The uniquely designed Integrated Management Process provides the path to develop, implement, and monitor an Integrated Management System in a simple but highly efficient and effective manner.

Jan 1, 1997

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By J. D. McBeth, G. M. Potter, Ramon Pizarro

Heap leaching is used by the Carlin Gold Mining Co., Carlin, Nev., to supplement conventional processing of gold ore by agitation-leaching and countercurrent decantation. Selected open-pit ore containing about 0.072 oz Au per ton is crushed to 3/4 inch, dumped by truck on an asphalt pad, and leached by sprinkling with dilute cyanide solution for 7 days. The heap is then drained and removed by front-end loader to tailings disposal. About 70 percent of the gold is dissolved. Leach solution from the heap joins the pregnant solution from countercurrent decantation for gold recovery by zinc precipitation. Four leach pads, each with a capacity of 1,400 tons of ore, are in use. About 10,000 tons of ore are heap leached monthly from about April through October. Heap leaching is recessed during freezing weather. Labor, equipment, and reagent requirements for heap leaching are presented.

Jan 1, 1974

E. S. BARDWELL,* Great Falls, Mont. (written discussion ?).-There are several points in. connection with the manufacture of ferromanganese in the electric furnace which it seems to me. might prove of interest in this connection. Recent observation of a, number of electric furnaces varying considerably in size and transformer capacity, and all working under the same conditions, shows the small furnaces to be much more efficient in operation than the large furnaces. The furnaces examined were all of the same type. The crucibles consisted of tanks varying in size from 71-z by 15 ft. by 4 ft. deep, to 12 by 20 ft. by 9 ft. deep, with linings formed of carbon electrode butts. The smaller furnaces had transformer capacity rated at 1500 k.v.a.; the largest furnace had a transformer rated at 3000 k.v.a. All of the furnaces were operated on three-phase, 60-cycle current, the three electrodes being in a straight line. The voltages varied from 65 volts in the smaller to 100 volts in the larger furnaces. The charges consisted of manganese ore, coal, iron turnings, and limestone in proper proportions. The small furnaces, operating at low voltage, were making good recoveries. The slag loss was low and the volatilization loss almost nil. The larger furnaces, operating at higher voltages, showed increased loss of manganese in the slag and greatly increased volatilization loss when working on the same charges as the smaller furnaces, or on charges similarly calculated. The exact reasons for this state of affairs are difficult to state; a number of factors probably contribute to the results obtained in the large furnaces. First as to the effect of the higher voltage on manganese content of the slags. Increasing the voltage of the furnaces apparently tends to promote irregular working. The current takes the path of least resistance; this means superheating in certain areas in the crucible and insufficiently high temperatures in adjoining areas. The partially reduced manganese in the cooler areas passes into the slag and escapes further reduction.

Jan 11, 1918

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By B. M. Currell, M. J. Neate, P. W. Bowden

Historically the hydrogen fluoride laden fume emitted from the electrolytic cells in the aluminium reduction process is further treated in pulse jet dust collectors. These dust collectors act as dry scrubbers performing two duties: adsorbing the gaseous fluoride emitted from the cells onto alumina dust; and collecting the alumina dust minimising particulate and fluoride emissions to the environment.Patented StarBag (TM) technology has been used in aluminium smelters in Australia as a means of increasing the dust collection and fluoride scrubbing capacity of existing collectors. This technology provides an alternative to major capital equipment upgrade where increased capacity is required, and potentially lowers the production cost per tonne of aluminium where capacity limitations are being realised and production expansion is required. This paper presents the findings of on-site pilot scale, and full production scale comparative tests, highlighting the operational and variable differences observed utilising the Star-Bag(TM) technology at Boyne Smelters Ltd in Australia. The results illustrate how this technology can be utilised to increase the hydrogen fluoride scrubbing efficiency and dust collection capacity of existing capital equipment.

Jan 1, 2006

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Yan D. S

The removal of antimony from a refractory gold-bearing stibnite ore by roasting and selective chlorinating roasting was investigated. The influence of roasting temperature, roasting time, roasting atmosphere and type and amount of chlorinating agents on antimony removal were studied. The laboratory studies carried out included roasting tests of 4 g samples in a laboratory rotary kiln, followed by 400 g samples roasted in a fluidised bed. The test results revealed that antimony was efficiently removed by roasting at temperatures over 800¦C in a nitrogen atmosphere. The most efficient volatilisation of antimony was achieved with the addition of ferric chloride at temperatures between 350-600¦C.

Jan 1, 1995

By A Xenidis, N Papassiopi, I Paspaliari

Acid generating sulfidic tailings covering a surface area of approximately ten hectares have been deposited in the historic mining area of Lavrion in Greece. For the development of a remediation strategy, the performance of three alternative acid generation control techniques was assessed under actual field conditions. The techniques involved the application of dry covers, including a synthetic HDPE liner and a compacted clay layer with capillary barriers. Furthermore, the potential formation of a low permeability hardpan layer at the sulfidic tailings surface by limestone addition was investigated. The field tests covered an area of 2500 m2, which was divided in equal quadrants, corresponding to the control plot and the three alternative remedial options. To monitor the amount and quality of percolated water, lysimeters were installed beneath the four plot areas. Based on the monitoring results over a period of six years, due to the dry climate encountered in the Lavrion area, a low amount of water percolates through the pyrites if no action is taken (control area), corresponding to 20 - 25 mm per year. This water is highly acidic, pH = 1.2, and contains a heavy load of contaminants, eg Fe 40 g/L, Zn 15 g/L, and As 1.5 g/L. The HDPE cover eliminated the percolation of water into the material for a period of five years, whereas thereafter the volume of leachates increased to values similar to those recorded in the control plot. The water collected in the lysimeter of the clay cover has been minimal corresponding to approximately five per cent of the drainage volume produced in the control area. In the fourth plot, which involved limestone addition to sulfidic tailings, the volume of drainage initially collected was almost double compared to the control area. After three years of monitoring, significant reduction in the amount of percolated water was observed, attributed to the formation of a cemented layer (hardpan), at a depth of 40-80 cm from the testpad surface.

Jan 1, 2003

By Allan E. Koski

Michigan is the second largest iron ore producing state in the United States. The Empire Mine, celebrating its 30th anniversary in 1994, is the largest iron ore mine in the state. The Empire Iron Mining Partnership is an iron ore mining, concentrating and pelletizing facility managed by The Cleveland-Cliffs Iron Co., a subsidiary of Cleveland-Cliffs Inc. The Empire Mine is located near Palmer, MI on the Marquette Iron Range in Michigan's Upper Peninsula. The partnership includes Inland Steel Co., LTV Steel Co., Wheeling-Pittsburgh Steel Corp. and Cleveland-Cliffs. Mine construction began in 1960. The first pellets were produced in late 1963. Successive expansions in 1967, 1974 and 1979 resulted in Empire reaching a present annual capacity of 8.1 Mt (8 million long tons) of pellets. In late 1993, a milestone was reached with the production of Empire's 152-Mt (150-millionth long ton) of iron ore pellets.

Jan 1, 1994

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By R. S. Knappen, D. V. Carter

In the states east of the Mississippi River, oil field operations were generally restricted during 1927. Active drilling was chiefly confined to the flood district of Bradford, and to the new areas in western Kentucky, Michigan, and southwestern Indiana. In spite of the general depression, production increased in every state, except Illinois. This unexpected increase is. due to several factors. First, in 1926 there was little flush production outside of Illinois, and the decline 'curves in all states are exceedingly flat. Second, the floods in Bradford, Pennsylvania, and Allegany County, New York, proceeded normally and increased production in those states for the fourth consecutive year. Third, new pools in Kentucky, Indiana and Michigan gave important flush production. Fourth, the general unsatisfactory market forced the operators to scrutinize carefully all their operations and improve efficiency and production in all possible ways. Increases amounted to approximately 2,000,000 bbl. Illinois lost, 900,000 bbl., leaving a net gain for the states east of the Mississippi River amounting to 1,100,000 bbl., or a total 40,268,000 barrels. Pennsylvania and New York In northern Pennsylvania and southern New York, the principal activity centered in the districts where flooding is being used to increase the recovery from the old districts. Once started, the flood cannot be shut off. The producer must drill wells and take his oil on schedule, or irrevocably lose it. Accordingly, in face of an adverse market Bradford and Bolivar operations increased 24 per cent. This area furnished more than 40 per cent. of the oil wells completed east of the Mississippi River last year, although the average initial production was less than 2.5 bbl. Unlike all normal fields, this production increases for several months until water appears in the well. For this reason, these wells will produce much more oil than would appear probable from the statement of initial production. During the year, air or gas pressure was applied to several new properties. Surplus gas is rarely available and air has been more commonly used. Two explosions occurred as a result of recycling air-gas

Jan 1, 1928

By J. Labuschagne

There are a number of factors that contribute to the profitability of a mine and its associated concentrator. Chief among these is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. The main aim of this project was to integrate the mining model with a concentrator production schedule to minimize the time it would take to produce concentrate (without the concentrator having to stop because of a lack of feed material) in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where 'visual pollution' is to be avoided. To achieve these two goals a dynamic stockpile model was created by utilizing the mine production schedule and breaking it down to a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ore. To prevent a situation where the concentrator was operational without any feed, the stockpile levels were never allowed to fall below zero. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, which was used as a basis for commercial negotiations for the sale of concentrate.

Jan 1, 2013

By Eifu Moriyama

In 1953, Akita Plant, having a capacity of 560 tons per month, was built at Akita city by Mitsubishi Metal Mining Co., Ltd. for the purpose of treatment of the Ikuno and Akenobe Mines's zinc concentrates. Akita city, in whose neighborhood the black ore has been discovered, is located about 500 Km north of Tokyo and faced with the Japan Sea. This plant has been continuously expanded to have the capacity of 7,500 tons per month by the end of 1969. Efforts have been made to mechanize installations and to achieve continuous process. One of the characteristics of Akita Plant is the recent establishment of the residue treatment process. Many processes had been investigated, and finally commercial sulphate roasting of the residue has been carried out since 1965. At Akita Plant, special high grade electrolytic zinc, zinc alloy for die-casting (MAK brand), cadmium, cement copper and sulphur dioxide gas are produced. Sulphur dioxide gas is sent to the next door fertilizer plant to make acid. Table 1 shows production and the average assay of the electrolytic zinc and cadmium in 1969. This plant is divided into four main sections, two subsections, and residue treatment sections: Main sections are: (M-1) roasting section, (M-2) leaching and purification section, (M-3) electrolysis section, (M-4) melting and casting section,

Jan 1, 1970

AT THE beginning of October, the outstanding feature in the world's affairs was the Turkish question. The Turks, victorious over the Greeks, repudiated the treaty of Sévres with the Allies and demanded their reestablishment at Con-stantinople and in Thrace. The British resisted, but deserted by the French and Italians, at a military conference at Mudania the Turks obtained about everything that they wanted. Great Britain suffered a loss of prestige that may bear evil fruit in the future. The possession of the Dardanelles by the Turks pro-duced the ruin of Russia and Rumania in the great war, prolonged it two years and made it necessary for America to go in. Disruption of the entente puts the Turks back where they were. In America a strong and spontaneous reaction developed against this, not for any diplomatic reasons, but purely out of the sentiment that the atrocious Turks should be confined to Anatolia. Some strong leadership would have aligned the United States with Great Britain in this matter. As it is, the French have had their way but have alienated much of their American friendship. The temporary composition of Turkish affairs at the Mudania conference had momentous consequences. The Greeks, having expelled King Constantine, in their distress and despair reverted to the guidance of Venizelos. Evacuation of the Grecian military forces and the entire Grecian population from Eastern Thrace began, the people not venturing to remain there. From all accounts their withdrawal, attended by great hardships, was reminiscent of folk movements in the Middle Ages. The vanguard of the Angora Govern-ment set foot in Constantinople, marking the return of the Turks to Europe, while the Allied forces remain-ing there temporarily stood in chagrin. In Great Britain an important element of the Con-servatives withdrew their support from the Coalition Government, thus leading to the resignation of Lloyd George, the installation of Andrew Bonar Law as premier and a general election with a tri-party contest among the Conservatives, Liberals and Labor, called for Nov. 15. Civil war continued in Ireland, but attention was diverted from it by the more important events in the Near East.

Jan 11, 1922