Search Documents

By Carlton E. Brown

Impinger dust-counting methods are used by industrial hygienists for determining the number concentration of unhygienic siliceous dusts in industrial atmospheres. Various statements have been made regarding the size of the smallest particles revealed by the microscopic employed in such determinations. Published data on the subject are quite limited. This report presents information on the size of the smallest particles revealed by light-field and dark-field techniques applied to impinger and electric precipitator samples collected from experimentally established aerosols of silica dust and bituminous-coal dust. Size distribution and number concentration of particles of the various sizes in the aerosols were determined from samples collected by thermal precipitation simultaneously with the impinger and electric precipitator samples. The size of the smallest silica and bituminous-coal dust particles determined in the light-field counting method used was about 1./1, . There was relatively little variation in the values from 8 impinger and 33 A.-C. precipitator samples of silica dust and 13 impinger and 13 A.-C. precipitator samples of coal dust. The coefficients of variation of the values from the four sets of determinations were low, ranging from ± 7.7 to t 10 percent. This size of 1,14 is close to the limit of resolution of the microscopic method used and to various previously suggested values. The size of the particles determined in the dark-field counting method used was smaller than the size (about 0.28A ) of the smallest particles determined in the light-field, oil-immersion method used for the thermal precipitator samples.

Jan 1, 1951

The 48th convention of the International Union of Mine, Mill and Smelter Workers, held in New York City recently, saw delegates vote funds for a new organizational drive expected to begin immediately. John Clark, union president, told members in his keynote speech, that the union would be in a better position to make demands if it extended its membership to all phases of the nonferrous -industry. He told the 250 delegates that union leaders have already laid extensive groundwork for the campaign. Clark said: "I am proposing here that we concentrate on organizing during this coming year. I am proposing that we throw a heavy amount of re sources in organizing. That means financial resources as well as re- sources of staff ."

Jan 1, 1952

By Alan M., Bateman

MR. JORALEMON'S dispassionate discussion of this subject in TECHNICAL PUBLICATION 340 of the Institute shows clearly some of the failures and successes of geology in the discovery of ore deposits. He forces us to recognize, with humility, that chance has played a greater part than geology in the recent discovery of several great copper deposits. I think, however, he wrongly ascribes to unexpected or chance discovery some deposits that were found as a direct result of geological investigation. I refer to the Rhodesian copper deposits,, particularly Roan Antelope and Mufulira, both mentioned by him as having been found by chance. Also,. I think Mr. Joralemon's paper, inadvertently, does not- give the proper credit for the early recognition of the possibilities of these deposits. I feel sure that Mr. Joralemon and the gentlemen given credit by him will welcome any further information on this subject that will throw light on what will some day- be of. historical interest and importance. Consequently, I should like to set forth some additional data that throw light on who should receive the most credit, and' to indicate that, in my opinion, sound. geological reasoning and not chance is to be, credited for the development of the. Roan Antelope and Muf ulira mines.

Jan 1, 1931

By Aldo Henrique de Almeida Barbosa

A demanda do setor automobilístico por aços revestidos destinados à conformação a quente vem crescendo substancialmente nos mercados brasileiro e mundial, por eles possuírem boa conformabilidade e, após conformação, terem sua resistência significativamente aumentada. A busca por alternativas de revestimentos para essa aplicação está focada no revestimento galvannealed (GA), visando garantir a sua integridade durante o processo direto de conformação a quente. Nesse trabalho, foram desenvolvidos, em escala de laboratório, ciclos de recozimento e de galvannealing para o aço 22MnB5-GA, visando tornar o revestimento GA capaz de suportar as aplicações de conformação a quente para a indústria automobilística. Foram avaliados, também em escala de laboratório, tratamentos de austenitização desse aço. As melhores condições, tanto de produção do revestimento quanto do tratamento térmico para conformação a quente, foram validadas industrialmente. Os resultados mostraram a viabilidade de se utilizar o aço 22MnB5-GA em aplicações de conformação a quente, com excelente qualidade superficial, propriedades mecânicas e microestrutura do substrato ajustadas à aplicação, inexistência de trincas no aço, boa aderência e aparência da camada de tinta e, também, bons desempenhos em termos de resistência à corrosão e de soldabilidade.

Aug 17, 2017

WMC Limited, owner/operator of Olympic Dam, the worldÆs largest underground uranium mine and the fourth largest underground copper mine has now completed an expansion that has been classed as a benchmark in the mining industry. To achieve a production increase from 3.4 to 9.25 Mtpa from an underground mining operation in two years was a major challenge, it was essential to review the overall materials handling system from æthe face to the stockpileÆ. The challenge was two-fold:How to deliver 30 000 tonne of ore per day to the processing plant, from a single underground mine? To provide the processing plant with a consistent metallurgical feed. This paper traces the transformation from the old to the new materials handling system at Olympic Dam.

Jan 1, 2000

By R. Havens, K. C. Dean, H. Dolezal

Mine, mill, and smelter wastes aggregating billions of tons are scattered across the country as unattractive barren piles that mar the natural beauty of the land. As the population of the United States increases and the demand for land intensifies, populous centers are slowly encroaching on these formerly isolated wastes. Encroachment sharply intensifies the importance of controlling the air and water pollution derived from natural weathering of such wastes. Use or stabilization of these wastes comprises the only viable means for minimizing pollution. Utilization is preferable to stabilization, because full use would both eliminate the waste and broaden the mineral resource base. However, the wastes typically comprise immense tonnages of materials discarded by selective mining or after recovering the significant mineral values by milling and/or smelting. Only rarely can such low-grade material be reprocessed to extract additional minerals at a profit. Some mineral wastes are suitable for disposal as mine fill, railroad and highway road ballast, and land fill. Similarly, some mineral wastes can be utilized as raw materials for making brick, rock wool, concrete, and ceramic products. Several means exist for stabilization of relatively fine-sized wastes, which constitute the chief sources of air and water pollution. These include physical, chemical, and vegetative stabilization, and combinations thereof. Massive coverings of coarse slag, concrete, and soil may be used to prevent erosion of waste piles. A variety of chemicals can be used to bond the particles of fine-size waste into a relatively inert mass. However, the most promising method of producing an esthetically appealing storage site is vegetative stabilization. Numerous species of plants can germinate, grow, and reseed in waste materials which have been adequately prepared to support plant life.

Jan 3, 1969

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly 100 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson's X-ray data indicate that this decomposition is accompanied by a change in volume of as much as 5 per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson' found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potter5 have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to 90 per cent Mn is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced 90 per cent when forged to ½ -in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By Felicia F. Peng

Using a fuzzy logic controller, a signal applied on the processes may be generated through a linguistic protocol expressing an operator's intuitive control strategies. In this work, fuzzy logic controller and PID controller imposed upon the feedback liquid level control systems for a stirred tank are studied and compared. The construction factors including the shape of membership functions, number of fuzzy variables, number of inputs, number of rules, and different defuzzification methods are considered in design and formulating the fuzzy logic control strategies and algorithms. From the analysis of the strategies and control performances, an optimum controller may be generated by making use of the best combination of these fuzzy construction factors.

Jan 1, 1997

By Manlapig EV, Lawson F, Clarkson CJ

A low grade middling sample from Mount Isa, Australia, assaying 31.7 per cent zinc, 12.9 per cent lead and 14.5 per cent iron was leached under atmospheric pressure in sulphate and sulphate-chloride solutions with ferric ions as oxidants. About 96 per cent of the contained zinc was dissolved into a 0.5 M H2SO4 - 0.5 M Fe2(SO4)3 solution at 90¦C within three hours from a five per cent by weight slurry density mixture. The leaching process is very temperature-dependent, suggesting a surface chemical control. In the latter stage, the leaching rates levelled off and the leaching was most probably controlled by both surface chemical reaction and diffusion processes. The addition of chloride ions in the leach solution resulted in an increase in the leaching rate. About 95 per cent of the lead sulphide contained was converted to lead sulphate which precipitated and remained in the residue. Essentially no lead remained in solution and the low chloride concentration did not affect the precipitation of lead sulphate. Half of the iron orginally present remained in the residue as pyrite although essentially all the cadmium and 90 per cent of the copper initially present were dissolved. Some three per cent of sulphide sulphur was oxidised through to sulphate, about 67 per cent was converted to elemental sulphur which can be recovered by solvent extraction, the rest remained in the residue mainly as pyrite. Ferric sulphate and sulphate-chloride solutions can be used to effectively leach finely ground lead-zinc middlings and other bulk sulphide concentrates. A complete separation of zinc from lead and silver has been demonstrated.

Jan 1, 1993

By J. R. Thoenen

Six or seven years age the United States Bureau of Nines started development of instruments for the purpose of accurately measuring the vibrational movement of the earth in the vicinity of quarry blasts. V For this work a new type of seismometer has been developod.1/ A number of these have been constructed, the accessory field equipment has been assembled, and approximately 200 field tests of actual quarry blasts have been made. The results of some of these tests have been. published 2/ and others arcs the subject of two manuscripts now in preparation. So far the attention of the investigation has been centered on ascertaining the characteristics and behavior of the ground vibrations. Occasionally, when opportunity Prose, measurements of the vibrations occurring in houses or other structures caused by quarry blasts were made, but without Piny attempt et direct correlation or interpretation. During; 1936 the National Bureau of Standards conducted some experiments to determine the normal vibrations to which the walls and floors of buildings are subject. Cooperation of the Bureau of Mine's was requested in measuring the displace-ment. This afforded an opportunity to study the affect of mechanically induced vibrations end make limited comparison with previous records of vibrations from blasting. This paper duels with the experiments made in cooperation with the Bureau of Standards and includes soma comparisons with affects from quarry shots. The results are in the: nature, of , progress report only, and are not intended to draw definite conclusions. Those, tests were concerned with the determination of the maximum amplitudes of vibration possible in the floors and walls of a typical dwelling when subjected to commonly experienced vibrations. The dwelling tested was obtained by the National Bureau of Standards. It was a large four-story stucco building, 41 ft. south off the southerly curb of Park Road, in. Washington, D.C., which was constructed about 1900 and was supported on overburden. The basement floor elevation was approximately that of the pavement of Park Road. Park Road runs east and west; the front door of the house faced north.

Jan 1, 1937

By A Black, J H. Youngson

At least 85 000 tonnes of mine tailings were discharged into Deepdell Creek, east Otago between 1890s and 1940s. The tailings contained about 1 wt % arsenic, so about 850 tonnes of arsenic in the form of arsenopyrite was discharged. Annual floods have removed nearly all tailings within c. 60 years. Small amounts of arsenic-bearing sediments (<250 ppm) remain in Deepdell Creek. About 7 kg/year dissolved arsenic was discharged in groundwater from mineralised Hyde-Macraes Shear Zone rocks in the vicinity of the historic mine sites. Adsorption of this arsenic on to iron oxyhydroxides in the stream sediments may have contributed to the elevated As content of those sediments. Even less arsenic remains in the main Shag valley below the Deepdell Creek confluence (15 - 25 ppm As). Rare relict arsenopyrite grains are trapped in bedrock crevices 25 km from source. No tailings deposition is detectable in theShag River estuary, and the tailings have presumably been discharged into the sea. Natural rehabilitation of the Shag catchment has been rapid and effective.

Jan 1, 2004

By C. A. Jeffrey, K. Pearson

The Croft diorite in central England belongs to a suite of Caledonian igneous rocks collectively known as the South Leicestershire diorite complex. Although the intrusions occupy separate outcrops, they are linked at depth to form a single pluton, buried beneath a cover of Triassic sediments (Le Bas, 1972; 1982, Allsop and Arthur, 1983). Both the Caledonian diorites and the over-lying sub-Triassic unconformity have been affected by a complex history of alteration and mineralization which can be subdivided into four stages: (1) deuteric effects, caused by the release ofvolatiles during magmatic cooling; (2) albitization through sodic enrichment; (3) formation of low-temperature laumontite, analcime and calcite veins with associated wall-rock alteration to prehniteand pumpellyite; and (4) sub-Triassic unconformity-hosted base metal, manganese and palygorskite mineralization. Zeolite mineralization occured some 200 Ma later than the intrusion itself, duringpost-Triassic times, as indicated by the presence of a single vein of laumontite and microcrystallinecalcite which cross-cuts the sub-Triassic unconformity surface and enters the overlying Triassic sediments. Evidence from ?uid inclusion work indicates that two ?uids were involved in the deposition of the zeolite veins. One ?uid was initially of relatively high temperature (~100°C to 320°C) and lowsalinity (~0.2 to 5.9 wt% NaCl equiv.), and was probably meteoric in origin, whereas the other wasof relatively low temperature (~41°C to 165°C) and high salinity (~0.4 to 16.72 wt% NaCl equiv.),and is interpreted to represent a basinal brine. During Triassic rifting, thinning and fracturing of the crust, with the possible rise of associated magmas (Halliday and Mitchell, 1984), could have increased permeability and heat ?ow, initiating the circulation of hydrothermal ?uids. Triassic unconformity-hosted base-metal mineralization in Central England is similar to other Triassic-Juras-sic mineralization in Europe (Mitchell and Halliday, 1976).

Jan 1, 1997

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By C. W. Andrews

The various methods of by-product coke-manufacture have been quite thoroughly discussed in a number of papers recently published, and I think it would possibly be of interest and value to discuss the growth and probable future of the byproduct coke industry, rather than details of manufacture. The first by-product coke-plant in the United States, consisting of 12 ovens, was put in operation at Syracuse in January, 1893. This installation was followed by one at Johnstown, Pa., in 1895; one at Dunbar, in 1896, and one at Glassport, in 1897. The plant at Syracuse was primarily intended to supply the owners with ammonia for their alkali-works. At Glassport, for the first time, gas was sold for illuminating purposes, although it was mixed with water-gas to make it marketable. The New England Coke & Gas Co. started the plant in Boston in 1899, which was destined to change the whole trend of the establishment of by-product plants, since it manufactured for the first time illuminating-gas suitable for sale without enrichment. This was accomplished by dividing the gas on the battery into two portions. One portion, consisting of the richer part of the gas, was saved for sale, while the remaining, or leaner, portion was used in the battery. This idea was originated by Dr. Schniewind, of the United Coke & Gas Co. The coke was used for domestic, industrial, and locomotive fuel, as its sulphur-content was too high to make it suitable for use in the foundry. The successful operation of this plant led to the building of additional plants at points where the production of illuminating-gas could be sold to advantage and where there was a fair market for the coke-output. The following list of illuminating-gas plants in order of construction will give a good idea of the rapid growth of this method of combined gas- and coke-manufacture: Hamilton, Ohio; Detroit, Mich.; Camden, N. J.; Baltimore, Md.; Chester, Pa.; Milwaukee, Wis.; Duluth, Minn.; Geneva, N. Y.; Chicago, Ill.; Indianapolis, Ind. In addition to these there are now under construction plants at Muncie, Ind.; Joliet, Ill., and Waukegan, Ill., all of which will produce illuminating-gas and metallurgical coke.

Jan 1, 1913

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy's extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By R. S. Archibald

THE Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sets. 3, 4 and 5, T. 47, N.R. 28W. and sets. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 2 1/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Mar¬quette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette.

Jan 1, 1935

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995