Search Documents

By B. Pollack, L. G. Stevens

INTRODUCTION In other chapters of this volume many of the important technical aspects in the design of concentration and dewatering circuits have been discussed. This chapter will deal with the steps necessary to bring that information together in order to produce the specifications necessary to purchase the equipment and complete the design. It deals with the plant as a whole rather than just concentration and dewatering, since the steps are essentially the same. Prerequisites to Engineering Design Feasibility studies will have been completed and design parameters established prior to the start of the engineering design stages for a metallurgical plant. The data base for the feasibility studies will have included laboratory and/or pilot plant test work, historical data, proposed plant site data such as climatology, topographic mapping, geological and geotechnical information. These studies will have established the general project design criteria as well as the process design criteria leading to the preparation of preliminary flowsheet ( s) and/or alternative process flowsheets. These will have incorporated metallurgical and material balances, allowing identification of major equipment items, and development of preliminary plant site plot plans. Preliminary technical and economic assessments and recommendations will have been prepared during this phase for Owner's review and evaluation of the technical, physical, and cost effectiveness of the overall project and its component process, process facilities, and supporting facilities elements. After Ownert s approval and decision to proceed, the engineering design can be initiated, using the above information as the basis. Engineering Design Phase The engineering design of metallurgical plants and their elements are generally developed in two sequential stages, namely: (1) Basic ("Front end") Engineering Design (2) Detail Engineering Design Figure 1 relates these engineering stages to the entire program from feasibility through construction.

Jan 1, 1986

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible lighting while persons are working in such places. Section 317(e) further provides that such working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31, 1970, a notice of proposed rulemaking which prescribed the illumination to be provided in the working places of underground coal mines. In light of written comments, suggestions, and objections to this proposed rulemaking, the proposed standards were withdrawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974, and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting-standards &k place on October 1, 1976, which means that the underground coal mining, industry must comply with face illumination requirements by April 1, 1978.

Jan 3, 1978

By J. W. Dini

Introduction The mission of the Materials Fabrication Division (MFD) is to provide fabrication services and technology in support of all programs at Lawrence Livermore National Laboratory (LLNL). MFD involvement is called for when fabrication activity requires levels of expertise, technology, equipment, process development, hazardous processes, security, or scheduling that is typically not commercially available. Customers are encouraged to utilize private industry for fabrication activity requiring routine processing or for production applications. MFD is .a large diversified service organization including approximately 400 full time employees. The group provides a wide variety of processes including all common machining and fabrications operations, laser and water jet cutting, electrical discharge machining, lapping, electron beam and laser welding, vacuum brazing, heat treating, forming, electroplating and metal finishing, optical polishing and grinding, vacuum coating, vacuum engineering and a variety of plastics operations. These operations occupy more than 1,250,000 square feet of floor space. For more detail on the many fabrication related services available from MFD, see Reference 1.

Jan 1, 1992

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

• "This country eventually may have to rely on foreign sources for some metals, not because it does not have them here but because it may have difficulty getting the labor to mine them. Few people realize the extent to which the 'old timers' are still the backlog of the important districts." --Fred Searls, Jr. • A new filter has been developed by Arthur D. Little, Inc., for the ABC which will remove all dust from the air. Submicroscopic asbestos fibers are used as filter media and are claimed to stop all dust and pollen while passing suitable quantities of air. •Out in front public relationswise is the Peabody Coal Co. which has launched a 15-min television news program on WNBQ at 10:30 C.S.T., Tuesday and Thursday nights. Clifton Utley, news commentator, will tell how coal is mined today and indicate, with pictures, the improvement in efficiency and safety which has resulted from today's mechanized operations. •Two hundred coal mining companies are using roof bolts as a means of supporting about 14 million sq ft of roof surface, Edward Thomas of the Bureau of Mines reported. Various types of metal and wooden pins can be used. The method was first used by the St. Joseph Lead Co. over 20 years ago, but is now being studied and adopted widely in metal, nonmetallic, and coal mines. * The first ten technical graduates have reported at Hanford Works in the state of Washington, to begin the newly installed General Electric rotational training program, believed to be the first of its kind at any U.S. atomic energy plant. The program is to provide suitably trained personnel for the nation's atomic energy program. •The need for top-notch scientists and engineers to stimulate mining programs in British colonies is acute. About 60 American experts are being sought for the ECA sponsored program. Positions for mining engineers, geologists, assayers, topographers, and petrologists are open. •Production of primary aluminum for the first quarter of 1950 was 322,4250008 lb which is 6 1/2 million lb more than was produced in the first quarter of 1949. Shipments of aluminum sheet, plate, and strip amounted to 259.772,1571b for the first quarter. •Policy on manganese procurement for the stockpile is being studied by a House Armed Services Subcommittee with the possibility of lowering specifications. The U. S. Bureau of Mines is drafting a bill to encourage domestic production for stockpiling through producer subsidies. 'It will have to be cleared by the Bureau of the Budget and other agencies before going to Congress. •Oil men consider dry holes a necessary evil in their search for oil. Last year 34 out of every 100 wells drilled were dry holes. Yet Texas Technological College is attempting to drill a dry hole on its campus at Lubbock, taking every precaution to make sure it is a "duster" so its petroleum engineering students can play around with experiments without being bothered by any messy crude oil. --Natural Resources Notes. •A portable alertness indicator which signals lethargy in persons doing monotonous jobs has been developed for the Navy's Special Devices Center. A possible application to hoistmen is indicated but broaching the matter to them would be tricky.

Jan 6, 1950

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By L. F. Tedsen, A. E. Flanigan, J. E. Dorn

SINCE aluminum-alloy sheet may be used occasionally at moderately elevated temperatures, the effects of temperature en the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 375°F. This paper deals with stress-rupture and [ ] creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24S-T Alclad 24S-T8I Alclad 24S-T86 Alclad 75S-T R301-T (clad) [ ] Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 211°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to boo hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). MATERIALS Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1946

By Robert F. Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field. THEORIES OF STATES OF AGGREGATION The electron theory of metals and the relation between possible electron structure and the magnetic properties have been discussed (317.307)† the electron theory of liquid metals, especially with respect to electrical conductivity, has been considered(306).

Jan 1, 1935

By G. S. Rice

With so tremendous a subject, an attempted review of the coal situation of the world in a short talk must necessarily be of a sketchy character. It is hardly necessary to tell a body of engineers that had it not been for nature's gift of coal the material side of modern civilization would never have reached its present status. On the other side, it is regrettable that it was a byproduct of coal, T. N. T., which made possible Germany's initial success in this war, because that country had an enormous development of manufacturing plants that could be immediately utilized to make this destructive agent: One sometimes hears the casual remark that when the coal of the world is exhausted we shall use electricity; but, of course, electricity is ordinarily only a means of transforming and transmitting energy derived from fuel or water power, and chiefly from coal. It is true, we have much undeveloped water power, but it is more or less remote from 'the, centers of industry; and when all shall have been developed it will not begin to supply the power requirements of the world. It is, however, reasonable to expect that before the world's supply of coal shall be exhausted, methods will have been discovered of harnessing other forces of nature, such as the tides, or the energy emanating from the sun. Petroleum and natural gas naturally come to mind, but the days of both, as fuel, appear to be numbered, although the products of petroleum, if economically used, doubtless will be available for internal-combustion engines, automobiles, trucks, and boats for a long time, provided the reckless use of crude petroleum as an ordinary fuel is stopped. The products of petroleum are too valuable to mankind for such waste to be permitted. The civilization of the world, therefore, appears to rest, and, so far as can be seen, will indefinitely continue to rest, upon coal. COal Resources of the World According to the compilation made by the geologists of the principal countries for the 12th International Geologic Congress, held in Canada

Jan 1, 1918

The mostly submerged New Zealand sub-continent has a complex geological history and an active oceanographic regime that provides opportunities and challenges for offshore mineral exploration. Known deposits include polymetallic Fe-Mn nodules and crusts, polymetallic massive sulfides, phosphatic nodules, titanomagnetitie ironsands and placer gold deposits. Currently exploration interest is high with some 3.5 per cent of the EEZ under prospecting permit or application.   Article 76 of the UNCLOS convention allows coastal states to have sovereign rights over areas of the seafloor that are natural prolongations of the landmass that constitute submerged parts of the continental margin as extended continental shelf. New Zealand has substantial areas of elevated ridges and plateaux beyond the 200 M EEZ that form extended continental shelf. New Zealand has nearly completed a ten year, $44.4 M programme to define its outer extended continental shelf. New Zealand will lodge its outer limits of the extended continental shelf with the UN-appointed Commission on the Limits of the Continental Shelf in 2006, which if accepted, will enclose ~1.8 million km2 beyond the existing EEZ. Ocean Survey 20/20 is a follow-on marine mapping programme to underpin resource exploration and environmental management of the EEZ and extended continental shelf.

Jan 1, 2005

Jan 1, 1923

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée."

Jan 1, 2017

Jan 1, 1910

By John C. Brower

Bolivia is nor a major gold producer but has produced continuously since pre Inca times. Production reached a peak in 1964 of about 4,000,000 grams and is currently about 1,000,000 grams. Production is mainly from the Tipuani River valley north of La Paz and is derived from Pleistocene basin fill: the Cangalli conglomerate and overlying terraces. Abandoned Pleistocene lake terraces south of La Paz in the Oruro area are another source of gold whose potential have not been realized. In both the Tipuani and Oruro areas, primitive hand methods are the principal means of production, with the exception of a single modern dredge. In spite of a long history of production, probably very little of the gold potential has been mined.

Jan 1, 1979

A key premise to this paper is that most people involved in the design and implementation of drilling and blasting operations could benefit from a greater understanding of the geological materials, deposits and landforms they are dealing with. The second key ingredient for successful blasting is the concept of blasting objective. Mine operators and blasting contractors must be clear on what drives their costs (blasting leverage) and should formulate blasting objectives and operational targets which help in this regard. Many operators ignore geology descriptors and features apart from the name of the rock and start crudely quantifying the rock mass properties in terms of uniaxial compressive strength, or even worse still as hard or soft. This occurs too early in the design process and not much attention is paid to the geological materials, geological structures and the characteristics of the deposit they intend to excavate. In effect the rock type name and the strength descriptor become the site geology. Furthermore many blasting operators do not formalise their blasting objective, do not set operational targets and do not measure results to the degree required for continuous improvement. In this paper a number of civil, surface mine and underground mine blasting applications are tabulated in terms of typical blasting objectives and common geological materials. A good description of geological materials can convey a lot of useful information for blasting operators if they are able to accommodate this knowledge. In addition a clear statement of the blasting objective and associated operational targets will maximise the likelihood of achieving blast-driven downstream productivity improvements. The æStarting at Both EndsÆ combination is deemed extremely useful for any continuous improvement blasting program.

Jan 1, 1999

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By William H. Mount

INTRODUCTION The requirements of mine ventilation demand the constant attention of the mine operator. Just as the physical mine structure changes with time, the ventilation requirements of a particular mine change considerably from season to season and even from day to day. No ventilation system can remain adequate indefinitely; and all systems require monitoring and adjustments to achieve proper ventilation. Instead of being given fore- thought and planning, mine-ventilation systems too of- ten are erected hastily, merely to correct an already un- healthy situation. The usual result is an inefficient and costly system that, in some instances, may prove in- effective in providing fresh air to the point of need. The ventilation of mines is a combination of both art and science. The fluid that must be moved is in- visible; its properties change drastically with temperature, barometric pressure, and humidity; and the methods of measurement are not precise. In part, ventilation engineering must rely upon the art of good industrial ventilation experience and sometimes even the trial-and- error method. However, the properties of air can be determined with relatively inexpensive equipment; with some care, measurement accuracies within 5% of the actual values can be obtained. Thus the art of ventilation gradually is being supplanted by improved engineering practices. Although the direction of flow and the volume may not be predicted correctly by airflow equations in every situation, it is better to try to predict the behavior of a given ventilation before installation than to proceed blindly with a system design. When used with the discretion that comes from education and experience, the basic laws of ventilation can provide sub-stantial insight into the design of an air-handling system; and they can prevent wasteful or even dangerous designs from being installed. Since the mine operators who read this text will have varying amounts of exposure to ventilation theory, the basic laws of airflow and of mechanical ventilation are presented in the first section. The emphasis has been placed on the interpretation and use of fan characteristic curves that are supplied by fan manufacturers. Considerable information can be obtained from these fan curves, particularly when they are used with a graphic model of the mine, drift, or duct in which the fan or fans are to be installed. A few minutes spent comparing the various characteristic curves can help the designer obtain the correct fan for the job. However, the under- standing of a few fundamentals is necessary; and this text has been prepared to provide ample and understandable information in a "how-to" style. In subsequent sections of this text, more down-to- earth subjects will be covered, including the problems of air recirculation, relative merits of installing fans in series or in parallel, expected maintenance requirements (vibration, lubrication intervals, etc.), fan noise and some remedies, effect of an inlet bell on the fan per- formance, basic air-measurement techniques and equipment, and similar miscellaneous items. Although this text is not intended to be a comprehensive bible of mine ventilation, it has been prepared as a guide that provides some useful information to individuals responsible for the quality of the underground environment. Every person working underground is en- titled to the safest environment that can be provided within the limitations of existing technology and at a reasonable cost. Adequate ventilation is well within both limits, provided that the system is designed intelligently, in conjunction with the mining plan, and not as an after-

Jan 1, 1982

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal--conductivity method because of the relatively small amounts of this inert gas present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method3/ and a continuous analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of Mines. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company4/. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation;- Production is checked against the helium removed from the gas, which before the installation of the thermal--conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

GOD the Almighty has all things well ordered; in G particular, the effects and attributes of the seven planets whose reign and course (by the grace of God) determine for the most part not only our own life and death but also the growth and decay of vegetable and mineral life, so that the aforesaid planets generate and develop in a wondrous way the ores of gold and other metals in minerals, rocks, and earths. Specifically, the Sun develops the ores of gold, the Moon the ores of silver, Venus the ores of copper, Saturn the ores of lead, Jupiter the ores of tin and bismuth, Mars the ores of steel and iron, and so on. Since, however, no ore is made alone but each is made and wrought so that it is associated with other ores, it is necessary to know the art of separating the thus-made ores after they have become metals; as for instance, silver from lead and copper; gold from silver, and so on. [2]* If this is to be done usefully, you must be able to assay and must understand everything that is needed in connection therewith. It is obviously true and clear as light of day that some kinds of copper contain silver and some kinds of silver contain gold. In order that you may be able to separate them, so that each is obtained by itself and can be worked with profit and re ward you need first of all a true assay for the values of such metal. The assay, by revealing how great they are, whether the pure has been obtained separate from the worthless matter, and what the admixture is, advises you whether it would be worth the expense and the effort to start mining operations. Assaying also indicates how much silver there is in a centner of ore or how much copper and lead there are in

Jan 1, 1949

By Bruna de Camargo Lemos

O objetivo deste trabalho compreende a realização da síntese de SnO2 dopado com aditivo Sr2 contendo diferentes quantidades molares de SrO (X)SnO2+(1-X)SrO, em que o cátion Sr2+ foi introduzido através do nitrato de estrôncio variando de 5 à 50 % em mol para uma mistura tanto em meio aquoso quanto em meio alcoólico, seguida da calcinação do pó resultante que é feita à 700°C com uma taxa de 10°C/min. Análises de caracterização como difração de raios X, área específica, calorimetria exploratória, picnometria a gás e determinação do ponto isoelétrico das suspensões aquosas foram realizadas de modo a verificar qual o agente dispersante mais apropriado para as características ácido-básicos da suspensão em questão. A partir deste determinar o potencial zeta do composto estudado através da eletroforese. Compostos intermediários a base de estanato de estanho foram identificados, e a deposição por eletroforese foi realizada com sucesso, uma vez que foi possível obter uma suspensão estável a partir dos pós cerâmicos produzidos.

Aug 16, 2017