Search Documents

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By Max J. Spendlove

The Federal Bureau of Mines has been a leader in resource recovery research since it was founded in 1910. Until the early 19601s, most of the projects were concerned primarily with the task of extending and improving conventional technology oriented to secondary metals and minerals upgrading and processing for marketable products of highest value. By the mid-1960's with the passage of the Solid Waste Disposal Act of 1965, all resource recovery research programs were increased in scope and intensity as an effort to solve the growing number of environmental problems and the rapid depletion of domestic energy and mineral resources. Many new materials were investigated including urban refuse, manufacturing, industrial wastes, and stockyard wastes. The objective was to promote maximum recycling as the most practical answer to problems of waste disposal, pollution control, and the short supply of minerals and energy. The new research projects ranged from the conversion of animal manure and other organics to oil, to the recovery of precious and common metals from demolished aircraft and electronic scrap. This profile includes brief descriptions of many selected research projects that typify, the total spectrum of Bureau of Mines research in the important field of resource recovery.

Jan 1, 1977

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By E. L. Garton

[Analyses of may crude oils produced in Louisiana are included in reports that t have boon published by the Bureau of Mines. The first report, giving, analyse of 6 Louisiana crude oils, was 3 published in 1921 and this was followed a year later by Report of Investigations 2416,4/ giving 7 additional analyses. The eleven most important of these analyses were incorporated in Bulletin 291.5/ issued in 1928 In 1934 analyses of 26 crude oils produced in southern Louisiana were published.6/ The percent report presents analyses of 72 additional samples of crude oil from 45 fields in 23 parishes In Louisiana.]

Jan 1, 1939

By Andrew F. Conn

This report summarizes the results from the first year of an anticipated multiphase program to develop improved coal mining equipment which utilize the CAVIJET? cavitating water jet method. This laboratory parametric study demonstrated the advantages of cavitating jets over non­cavitating jets in cutting coal, by producing comparable slot depths at one-fifth of the operating pressure, at better than one-half of the spe­cific energy. These results suggest that CAVIJET-augmented mining devices can be developed with compact, low-pressure pumps. Thus, CAVIJET should be capable of operating with safer, lighter support equipment, while providing all of the advantages (reduction of dust and sparks, reduced damage to cutters) of conventional hydraulic mining methods.

Jan 1, 1976

By Terry Muldoon

In conventional noncoal, room-and-pillar mining, the cutting machine is frequently a major source of airborne dust. Water is often used for dust control. An evaluation of typically used water systems during this program showed that they reduced dust levels by 60 to 70 percent over dry cutting when at least 0.5 gpm of water was applied. These systems, however, are only marginally effective in maintaining compliance levels and the added moisture causes operational problems. During the program, three additional dust control systems were designed, fabricated, and evaluated. The first, a hollow cutter bar, was designed to capture dust in the kerf at the cutting zone. The system was only marginally effective in reducing dust levels due to its lack of control of other sources. Large quantities of material captured by the system made it operationally questionable. The second, a machine mounted exhaust system, was extremely effective in capturing virtually all the dust generated in the heading. The captured dust was ducted out of the heading and exhausted downstream in the crosscut. Exhausting the dust without scrubbing, however, creates problems for personnel working downstream of the cutting machine. Successful application would require changes to the mine ventilation system and mining sequence. The third, foam, injected foam from an onboard generator through a channel to the cutting zone at the tip of the bar. Test results showed that foam, using 1/3 to 1/2 the total fluid quantity, was equally effective when compared to the mine's current water system.

Jan 1, 1983

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 1, 1977

By C. H. Larsen

A 9-month study of the uses of wire rope associated with U. S. underground coal mining is reported. Rope applications are broken down into hoisting and nonhoisting applications where "hoisting" refers to transport in vertical and inclined shafts. The former receives the greatest emphasis since it represents the most critical rope application from the stand-point of production and safety. The discussion of hoisting practice includes aspects related to the mine operators as well as those related to the equipment builders and wire rope manufacturers. U. S. state and Federal laws regulating hoisting and wire rope use are also presented and discussed. Canadian and other foreign hoisting practice and laws are included. The state of the art in electromagnetic nondestructive inspection of hoist ropes is presented. Capabilities and use of one Canadian electromagnetic device are discussed in great detail. Conclusions are drawn regarding the present state of wire rope and hoisting technology in U. S. coal mines. Recommendations are made for improving rope practice, in general, and hoisting, in particular, consistent with greater safety.

Jan 1, 1971

By Warren E. Morrison

A simplified energy model for the United States is quantified for a recent historical period. The basic model and calculated quantified structures are used for a number of analytical case studies that estimate midterm and long-range shifts in patterns of energy resources demand and required supply. Historical data series are presented for the years 1947 to 1965 in the form of integrated energy balances by source, form, and consuming sector. In case studies I to XII, conditional projections of historical trends of energy demand and required supply are made for the midterm period 1966 to 1980. The projections are carried out by correlation of major energy components with relevant independent variables such as major economic indicators. Simulations of the medium-range projections to 1980 are carried out by varying the assumptions for the determining variables to produce high-and low-range projections for the midterm period. Case studies XIII to XXII are long term contingency or technological forecasts to the year 2000. These cases assume technological changes or innovations that produce major shifts in the long term pattern of energy consumption and the mix of required resources. The domestic resource base is assessed in its ability to meet projected or forecast demand for energy resources under the midterm and longrun assumptions made in the various case studies. Various energy issues or problems identified from the analyses of the case studies are discussed, and possible alternative approaches to solutions to these issues or problems are suggested.

Jan 1, 1968

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

1. Domestic Production and Use: In 1975.12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 67% of production capacity. Washington, Oregon, and Montana accounted for 37% of the total production; Gulf Coast States 21%, Northern States 29%, and other Southern States 13%. Output of primary metal in 1975 was valued at $3.0 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1975, building accounted for about 21%; transportation 19%; electrical 14%; packaging 18%; and consumer durables, 9%.

Jan 1, 1976

By Hewitt Wilson

Until recent years the term "whiting" was applied exclusively to the water-ground chalks of certain north European countries. In many industries these are still considered superior to the whiting made from domestic limestone and marble. However, the latter material has replaced much of the European whiting in the American market, largely due to improvements in grinding and classification by American manufacturers.4 To encourage the domestic industry, the Bureau of Mines in 1931 undertook a study of the preparation of whiting from American raw materials and a comparison of the finished products with European whitings.

Jan 1, 1937

By Gene R. Reid

The contract objective is the development and in mine testing of an Automatic Fire Control System (AFCS) for mobile underground metal mining equipment. The effort described by this report covers the period from June 21,1975 through June 30,1976 and accomplished the following tasks: ? Preparation of Data Handling Plan and data acquisition which included visits to twenty mine sites in eleven states, visits to Bureau and MESA facilities, and a literature survey. ? Data analysis which determined the most hazardous type of vehicle for use in the demonstration, and design requirements for the AFCS, ? Development of recommended design concepts for the AFCS. ? Design and development of the AFCS including tests on a full-scale mock-up of a load-haul-dump (LHD) vehicle. ? Underground fire tests on an ST-2B-LHD vehicle at the Hecla Lakeshore mine Casa Grande, Arizona.

Jan 1, 1976

By William C. Cooley

A literature search and survey were prepared on the technology of surface hydraulic mining, with particular reference to its possible use in the United States forstripping overburden from surface coal mines. Extensive use was made of Russian references which were translated into English. The advantages and disadvantages of hydraulic mining and hydrotransport are identified as well as criteria for selecting potential applications. At present, the major U.S. application is in the phosphate industry of Florida and North Carolina. Potential locations for hydraulic stripping of overburden from coal seams are identified in the states of Alaska, Illinois, Montana, Washington and Wyoming. Other potential applications include the hydraulic mining of peat in Minnesota, and the stripping of overburden from lignite in Texas, Montana, North Dakota and South Dakota. Further research is recommended, particularly on the subject of dewatering of fine clay slimes to avoid water pollution and to permit rapid reclamation of mined areas.

Jan 1, 1976

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1989. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1990

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975