Search Documents

By Ralph E. Davis, Lyon F. Terry

The rapid expansion of the natural gas industry in this country during the past three or four years has necessitated the construction of a number of long and comparatively large diameter high-pressure pipe lines This period of expansion and construction is still at high tide, and the current year will doubtless surpass all prior years in mileage and capacity of gas line installation. The fundamental economics of the business of long-distsrier transportation of natural gas may be briefly and simply stated, although most careful consideration must be given the actual determination and integration of the several more important factors which determine the ultimate success or failure of such a project. Reduced to its simplest form, a sound natural gas transportation project requires: 1. A competent source of gas, where the combination of quantity of gas available, cost of production, and longevity meet the given requirements. 2. A market, reasonably certain to endure in the face of any probable competition, of satisfactory size and price, and having a sufficiently favorable load factor. 3. A cost of installation of pipe line systen and an operating cost such as will, with honest and reasonably efficient management, afford a net operating return sufficient to attract the necessary capital required. In a11 new projects of this kind it is necessary that thehe three cssentials to ultimate success be assured. Hence the necessity of competent surveys of gas supply, and of market, both industrial and domestic. The prudent engineer will allow for "factors of safety" in reaching his conclusions just as he would in the design of a bridge. This paper deals primarily with but one of the major considerations enumerated above, I. e, the economic design of the pipe line system. The "pipe line system" will be considered to include (1) the pipe Iine, and (2) a series of compressor plants along the pipe line for maintaining

Jan 1, 1929

By N. F. Manrique

El presente texto refiere el aporte de la química analítica como método de control en las operaciones de la industria minera. La química analítica trabaja con los métodos analíticos, los cuales están en constante actualización al tiempo que los análisis por instrumentación. En este sentido, se muestra que métodos analíticos clásicos como aquellos de reciente adaptación sirven para determinar el cobre, plomo, zinc, plata y oro, entre otros minerales, ais como se describe el rango, tiempo y costo para cada método utilizado.

Jul 20, 1961

By J. Loredo

In some rural regions of Peru, artisanal gold mining is currently an essential activity as it provides an important source of income. In the Huanca region (Ayacucho Department) gold deposits are not attractive for mining companies due to their reduced size, but they have enough interest for artisanal mining because of the ease and low cost of mining operations. Artisanal gold mining represents an important damage for the environment, because operations related to amalgamation processes using Hg result in special environmental problems besides the typical ones commonly associated to all mining activities. A preliminary sampling has been made in soils, materials from tailing ponds and surface water of the Acarí River, at the site of the Huanca village, according to networks specially designed for the particular conditions of the area. Studies accomplished revealed high mercury concentrations in soils and tailings. Chemical analyses of soils directly collected in the area of the active or abandoned ?quimbaletes? show mercury concentrations ranging from 15.3 mg?kg-1 to 44.2 mg.kg-1. Mercury concentrations in soils decrease as a function of distance from the before mentioned sources. Water quality of the Acarí River that flows through the area does not present important changes as a consequence of the mining and processing operations.

Jan 1, 2006

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By Baafi E. Y

Dragline monitoring systems are normally the best tool used to collect data on the machine performance and operational parameters of a dragline operation. This paper discusses results of a time study using data from a dragline monitoring syste

Jan 1, 1998

By Claude Bazin, Robert Grant, Mike Cooper

An analysis of the Pb recovery as a function of particle size was carried out for the CuPb rougher bank of a complex sulphide mineral processing plant. Results indicate that higher recovery may be achieved by optimizing the flotation feed size distribution. Simulation of the actual grinding circuit has provided guidelines to modify circuit operating conditions in order to improve product size distribution. Plant tests ar

Jan 1, 1991

By M. Dubrovsky, J. W. Evans

A laboratory scale cell (approximately 50 amps current) equipped with a fluidized bed cathode was used in a study of the electrodeposition of cobalt from acidified aqueous sulfate solutions The effect of current density (in the range 0.1 to 1 amp/cm2 of diaphragm), cobalt concentration (4 8 to 100 glliter) and catholyte pH (1 35 to 6 2) on current efficiency and energy consumption were determined. Generally the current efficiency increased with increasing current density and cobalt concentration Current efficiencies were comparable to those reported in the literature for conventional electrowinning

Jan 1, 1981

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By Yuanbo Zhang, Helei Zhang, Heng Yu, Guanghui Li, Zhengwei Yu, Tao Jiang

"Composite agglomeration process (CAP) is an innovative method for preparing blast furnace burden. For CAP, the classified raw materials of pelletizing feeds and matrix feeds are mixed, charged and sintered. The characteristics of these two kinds of feeds obviously affect the permeability of per-ignition bed, as well as the sinter productivity and quality. In this study, the Ergun equation is proposed to predict the pressure drop of CAP bed using the particle size distribution. The calculation process indicates that the Dv and the Em are the two tuning parameters. The results show that there is a gap between the calculated values by Ergun equation and the measured results by pressure drop testing facility. Eliminated this error by modified the Ergun equation and then validated it through experimental studies using simulated CAP mix and test facility. Therefore, the modified Ergun equation can be used to predict the permeability of CAP bed.IntroductionThe sintering process is one of predominant agglomeration processes for preparing ironmaking burden from iron-bearing materials. Sinter accounts for 70-80% of the blast furnace burden in China and the continuous improvement of sinter quality provides a guarantee to anterograde production of blast furnace. Sinter productivity and quality are strongly related to the permeability of the bed during sintering, which is dependent on the structure of the bed before ignition in the early stage [l]. The size distribution, the shape of granules and the bed voidage are the primary affecting factors to pre-ignition permeability."

Jan 1, 2013

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

By J. W. Oberholzer, C. F. Meyer

The increased use of continuous miners to extract thicker coal seams has necessitated the use of enhanced ventilation systems in the headings. Due to the increased face size, more ventilation is required to effectively dilute the liberated methane down to acceptable levels. If more air is directed to the face an increase in the entrainment of dust creates an increased potential for workers to be exposed to dust. To enable the ventilation systems to reduce the methane levels and the levels of the airborne dust the ventilation systems in the heading have to be carefully designed. The matter is made more complicated through the use of other ventilation methods like jet fans, air-moving sprayfans on the continuous miners and high capacity scrubbers on the continuous miners. To enable the design of a balanced ventilation system in seam heights of over five metres requires methods that consider the system in a three- dimensional manner rather than in a two-dimensional fashion. Through the use of computational fluid dynamics (CFD) coupled with appropriate methods of taking underground face ventilation readings these problems can be solved in a cost effective way. Using computer modelling, ventilation methods can be designed and assessed instead of using costly underground trials to test the alternatives. Use of this system has led to a higher level of ventilation design as well as a more effective method to combat the health and safety hazards in coal mine headings.

Jan 1, 1995

As I drove in from the airport on Sunday somebody said `On the right you will see Dun- troon, which is the military training school of Australia.' So I asked the driver, where did they get that name? `Oh,' he said, `from some people who built a house there. That was it's name- Duntroon.' It strikes a note with me because, that's the name of a 12th century castle on the west coast of Scotland where I spend what leisure hours I have and, therefore, it establishes the long connection between Australia and my native land. There is also a story I should tell you about the oil industry and its upsurge in Scotland recently which has resulted in great prosperity. And in Edinburgh, the walls of the banks are bulging-because of the incursion of foreign exchange and other resources.

Jan 1, 1978

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH's Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By I. H. Redeker

North Carolina is the leading state in the USA in feldspar, mica, and spodumene production. Mixed feldspar, spodumene, mica and quartz are mined from hard rock, open pit deposits and recovered by flotation from the fresh pegmatite type ores. Potash feldspar, mica, clay and quartz are recovered from weathered decomposed pegmatites. The North Carolina State University has a Minerals Research Laboratory in Asheville with trained personnel and flexible pilot plant equipment. The flowsheets for the feldspar, spodumene and mica producing companies and for large phosphate and glass sand flotation plants were developed and tested in Asheville. Examples and problems of pegmatite flotation are demonstrated with flowsheets and slides.

Jan 1, 1981

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006

Jan 1, 1961

It is now five years since the advent of gold-dredging in Australia, the State of New South 'Wales, or colony as it was, being the first to adopt this system of gold-getting, and the credit of its introduction rests with a member of this Institute, Mr. Chas. L. Garland, who commenced operations with his dredge on the Macquarie River, at the junction of the Muckerawa Creek, in the month of March, 1899. In this paper it is intended to give a brief history of the career of the gold dredge in New South Wales from that relate up to the present time, during which period the writer, as a designer of many dredges, has been constantly in touch with the subject in all its phases in this State; the points noted are the outcome of his observation in a general way, and to a great extent are apart from the design proper.Gold-dredging in New South Wales up to the present moment can hardly be designated an unqualified success...

Jan 1, 1904

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills' LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976

By M Begbie, R J. Norris, D J. MacKenzie

The Otago Schist is crossed by numerous deformation zones that formed in the latter stages of metamorphism and uplift of the metamorphic belt. These deformation zones are long (tens of km) linear features at the regional scale, and are generally narrow (km scale or less). Many of these structural zones separate schist domains with different rock types and structural/metamorphic histories. The Hyde-Macraes Shear Zone is one such deformation zone, and this zone hosts the active Macraes gold mine. The Rise & Shine Shear Zone, 80 km NW of Macraes, is also enriched in gold and has been mined historically. Mineralisation in both these shear zones occurred during the transition from ductile to brittle deformation as the schist belt was uplifted from greenschist facies metamorphic conditions. Recrystallisation of quartz and micas in the early stages was overprinted by cataclasis, with sulfide and gold precipitation throughout. Many of the other late metamorphic deformation zones formed under similar greenschist to sub-greenschist facies conditions, with similar overprinting of recrystallisation textures and folds by more brittle textures such as breccias. Under these conditions, originally regionally pervasive deformation at the highest metamorphic grades was evolving towards more focussed high strain zones at lower temperatures and pressures. Shear zones initially focussed fluid flow along microshears and mineral grain boundaries, resulting in 1 to 100 m scale alteration and replacement in the host schist, with only local development of quartz veins. Fluid flow was not controlled by open fractures, and the rate of fluid movement was probably slow and pervasive. After uplift into the brittle regime, the schist belt underwent tectonic extension. Extension was accompanied by development of swarms of steeply dipping veins, with localised mineralised normal faults. Hydrothermal fluid flow throughout this uplift history was a normal consequence of late stage devolatilisation of the metamorphic belt. Hence, all late metamorphic deformation zones should be considered prospective for gold accumulation.

Jan 1, 2005