Search Documents

By T. Brady, J. Johnson, J. Whyatt, B. Pariseau, M. Stahl

An elastic-viscoplastic material model allows for time-dependent rock mass motion in proportion to excess stress above the elastic limit. The model produces rounded stair-step curves of displacement versus time that are similar to those obtained from recent borehole extensometer measurements made in the central portion of the Ross shaft pillar at the Homestake mine. The work in progress, including two- and three-dimensional finite element analyses using the UTAH2/3 codes, indicates that the model is a step towards more realistic safety and stability analysis, but that inclusion of rock mass damage may be desirable.

Jan 1, 2000

Executive JVW REYNOLDS, Chairman SYDNEY H BALL E DEGOLYER WILLIAM H BASSETT SAMUEL A TAYLOR Finance GEORGE D BARRON, Chairman H A GUESS GEORGE OTIS SMITH Membership ] H CALLOW, Chairman GEORGE D BARRON WILBER JUDSON JOHN A CHURCH, JR H N SPICER Alternates LEWIS W FRANCIS LOUIS D HUNTOON F T RUBIDGE

Jan 1, 1923

By Edmund Kirby

THE results to come from the application of cheap oxygen to industry in general will be so great that it is not possible to enumerate them beforehand and still less to estimate them. We naturally think first of the fuel to be saved; yet this is only a minor item. The main results will be changes in methods of manufacture or of operation. The speed of operation will be greatly increased, with consequent savings in labor and fixed charges, and also, in most cases, in the cost of fuel. High temperature will be brought within the reach of every manufacturer, whereas it is now available only to those operating expensive electric furnaces located within reach of large water power. New speeds and new temperatures mean improvements and processes not thought of at present. Incidentally the changes in methods will probably change the location of important world industries, the tendency being to concentrate at the fuel centers. The whole subject is so new that most of the data which an engineer requires for definite estimates do not exist. All that is possible now is to obtain a general view of the subject with rough and fragmentary estimates for some of the industries with which we are specially concerned. Most of the figures presented deal with fuel saving merely because there are available no data from which to estimate the effect on speed of operation. When working out the practical problems involved in substituting oxygen for air, in most cases the change will be made step by step; by trying out air enriched with increasing percentages of oxygen. Such partial applications of oxygen will be temporary expedients during the transition and there will be no stopping place short of the complete substitution of air by oxygen. This final stage is therefore the one discussed in this paper.1

Jan 11, 1924

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By Mendoza F. Juan

En las últimas décadas, la minería subterránea ha optado por el uso del equipo mecanizado Trackless o minería sin rieles. Dado su alto costo, se ha previsto establecer un sistema de control que mida la productividad y así definir las causas de su bajo o alta rendimiento. En esta perspectiva, el presente trabajo señala el cálculo de probabilidades y uso del equipo en el interior y exterior de las unidades de producción de CENTROMIN-PERÚ, definiendo cada uno de los términos y determinando la fórmula de los cálculos para estructurar el sistema uniforme en la empresa.

Nov 8, 1984

By R. C. Philp, Allan Gibb

The term a matte " is applied to smelting-products so extremely diverse in composition and physical properties that it appears impossible to devise any generic formula to represent, chemically, the manner in which the varied proportions of the almost unlimited possible constituents combine with each other. Mattes produced in copper-smelting, in distinction from those produced in smelting-operations in which the recovery of cop per is secondary to that of other metals, cover a narrower range in composition. The copper-content of such mattes vary from 20 to 80 per cent., and even this range is much smaller in general practice since it is found advantageous, when possible, to produce mattes with about 50 per cent. of copper in the first operation. Further, it is unusual that arsenic or antimony occurs in copper-ores in sufficient proportions to form arsenides or antimonides in such quantities that they will separate out from the furnace-products, as is common in lead-smelting. Generally, the mattes produced in copper-smelting are composed mainly of copper (usually greater than 35 per cent.), iron and sulphur, the remaining elements being usually in proportions sufficiently small to allow of their treatment as impuritiee, rather than as essential constituents of the mattes. In modern practice of smelting copper-ores in blast-furnaces the tendency is to approach pyritic smelting as nearly as possible, the furnaces being low and the air supplied being largely in excess of that required for complete combustion of the carbonaceous fuel. Hence, the atmosphere of the blast-furnace thus used is usually oxidizing or nearly neutral, and, as a consequence, the reduction of metallic iron that was a necessary evil of former practice is of unusual occurrence in operations where the main object is the recovery of copper. Hearth-accre-

Jan 1, 1906

By Richard E. Chism

Jan 1, 1902

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operation at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry. Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle size distributions and brightness values have been prepared. Extensive drilling and bulk sampling of the deposit over eight years has shown that the ore body is large and of a high grade suitable for the production of premium quality coating kaolins. The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW). The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment the nature of the production process and details the

Jan 1, 1986

By Jack Bradbury

The open stope room and pillar method of mining is used throughout Ozark Lead Company's underground mine located at Sweetwater, Missouri. This method of mining produces an approximate overall ore extraction of 80%. Pillar recovery, on a limited and experimental basis, was started in January of 1979 to determine the maximum size underground opening that could be mined safely. Monitoring the roof and surrounding pillars for potential failure during this pillar recovery process was accomplished by utilizing a simple rod extensometer to measure roof sag. Boreholes 7.5cm in diameter were drilled 3.5m into the roof to spot any separations or cracks that might have propagated between the bedded layers of rock. Underground openings 85m in length by 46m in width have been mined successfully without roof or surrounding pillar failure. Continued measurements to establish long term results will be necessary.

Jan 1, 1981

By F. H. Willcox

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J.).-This paper is timely because of the changed conditions due to the great war, but apparently its scope is limited to oxidation process steels. Referring to the four numbered observations on page 199: No. 1 seems to ignore Johnson's discoveries about oxygen in cast iron. No. 2 ignores crucible steel. No. 3 ignores red short steel containing enough gas solvents to make it solid, while No. 4 assumes that a deoxidizer is necessarily a gas decomposer or solvent and vice versa, which it not always is. From these observations it is deduced. that the only hole-forming gas in steel is an oxide of carbon (CO presumably is meant), which is not true.

Jan 4, 1917

By A. D. Schwope, L. R. Jackson, A. M. Hall

IN the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of recrystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. MATERIALS USED IN THE INVESTIGATION Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table 1. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871°C in air and hot rolled to 3/8 in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hrs. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pct reduction) in 6 passes and annealing at 427°C for 4 hrs. This annealed wire was then drawn to 0.081 in. wire, (37.1 pct reduction) in 2 passes. Square rod was made by hot rolling wire bars to 9/16 in, rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 3 1/2 hrs at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°C for 3 1/2 hrs. Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 X 0.268 in. square, annealing for 332 hrs at 538°C and cold rolling to 0.257 X 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hrs in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from 0.015-0.025 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. EFFECT OF COLD DRAWING AND TENSILE STRAIN ON STRENGTH OF COPPER Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are

Jan 1, 1947

By B. Oraee-Mirzamani

One the most important tasks after excavation of tunnels is the implementation and installation of a support system. Tunnel collapse poses a safety hazard and can cause worker injuries. In addition, it may have a severe economic impact because tunnel collapse can stop production and ore transportation. Therefore, an appropriate and well-designed support system is necessary for collapse prevention and to help stabilize the tunnels. In this research, we suggest a support system for the Parvade1 underground coal mine. The study case is a common mining roadway tunnel in the E1 longwall panel in this mine. To design an appropriate support system, we used the finite element method (Phase2 software). The results of this research can be used to design support systems for future tunnels in this mine and any coal mine that has similar conditions.

Aug 1, 2013

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By Kathryn Hindmarsh

The most common method for the concentration of cyanide in gold leach circuits is based on the titration of cyanide ions with silver ions. This can either be done manually as a titration with a visual end-point or by using one of several commercial cyanide analysers which are 'based on the same titration but use a potentiometric end point This method has 'its limitations in the case of some ores such as those containing high amounts of soluble copper and those that are treated at low (less than pH 9) pH values in that the titration results do not accurately reflect the concentration of cyanide which is available for the dissolution of gold. This paper will present the results of the development of a novel "active" cyanide analyser which is based on the rate, of the reaction between gold colloids and cyanide. Gold colloids have a deep red colour and can be very simply prepared and stored for extended periods of time when stabilized. t has been shown that colloidal gold behaves similarly to metallic gold, dissolving in aerated sodium cyanide solutions to give the colourless Au(CNh-ion, This allows the reaction between the colloids and cyanide to be monitored spectrophotometrically at 520 nm. An automated instrument has been developed around this concept which can analyse a filtered pulp stream every few minutes with periodic calibration using standard cyanide solutions, Results of test work on synthetic solutions and solutions derived from several Australian gold plants will be presented as will the results of a comparative evaluation with a commercial titration analyser on a local gold plant

Jan 1, 1998

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By Ann G. Kim

Gas samples containing 02, N2, H2, He, CO2, CO, CH4, and trace amounts of C 2 to C6 hydrocarbons are analyzed by a gas chromatographic method that utilizes both thermal conductivity and flame ionization detectors. A porous polymer support and molecular sieve columns are used with argon as the carrier gas. A column selector valve makes it possible to perform a complete analysis either on one 1-ml sample in 40 minutes or on two samples in 20 minutes, one sample for each detector. Samples are introduced either by on-column injection or through a gas sampling valve. By varying operational parameters, the speed, sensitivity, and accuracy of analysis may be modified to suit a particular situation.

Jan 1, 1974

AIMS 1953 DIRECTORY SUPPLEMENT OFFICERS AND DIRECTORS 1953 President and Director ANDREW FLETCHER (2) New York City Past President and Director MICHAEL L. HAIDER (2) New York City President-elect and Director LEO F. REINARTZ (3) Middletown, Ohio Vice-Presidents and Directors 0. B. J. Fraser (2), New York City J. L. Gillson (1), Wilmington, Del. A. B. Kinzel (3), New York J. B. Morrow, (2) Pittsburgh, Pa. L. E. Elkins (3), Tulsa, Okla. * T. B. Counselman, Stamford, Conn.

Jan 1, 1953

By R. M. Bricka, T. J. Olin

Heavy metals contamination is an environmental problem at Army installations engaged in firearms training and munitions production. At these facilities, weathering and corrosion of expended munitions and leaching from wastewater lagoons, landfills and burn pits have resulted in heavy metals contamination of the soil. The principal metals encountered in firing-range soils are lead, copper and zinc. Cadmium and other metals, such as antimony, that are often incorporated in the munitions are sometimes seen in lesser concentrations. Mercury is associated with various propellants and, while present in much smaller concentrations, is of concern because of its acute toxicity. Chromium is primarily associated with plating operations. The transport of metals into groundwater has been confirmed at some locations, which has required treatment of the soil and groundwater at these sites. Certain treatment processes for contaminated soil produce metals-laden extracts, which also require treatment before reuse or disposal. Ion exchange is generally quite effective for removing metals from aqueous streams. However, resins are expensive and must be regenerated, and activated carbon is generally less effective for most metals and also requires regeneration. Therefore, alternative effective and economic sorbents are needed. Twelve sorbents were screened in initial batch testing. These included activated carbon, bark, chitosan, crown ether, corn cob, xanthate, clay (kaolinite and montmorillonite), peat moss, seaweed and reagent-grade zeolite (aluminosilicate, Sigma Product No. Z3125). Of these, zeolite demonstrated the highest capacity for Pb, Cr and Cd. For this reason, zeolite was selected for further testing in batch, kinetic and column studies. Materials and methods Zeolite. The zeolite used in the second-phase batch and column studies was obtained from a natural deposit of clinoptilolite-rich rock located in South Dakota (Rocky Ford SDH) (Desborough, 1996). Large blocks of the material were crushed and sieved into the following three particle size ranges: 0.5 to 1.0, 1.0 to 4.0 and 2.0 to 4.7 mm. This material demonstrates high structural stability in acidic solutions (pH 2.5) (Desborough 1996) and has a measured surface area of 30 m2/g. The measured total cation-exchange capacity (TCEC) was approximately 10 meq/100 g. This is well below what has been indicated for commercially available zeolite, which has been reported to be about 180 to 220 meq/ 100 g. The TCEC test was repeated (Method 9081, SW 846) using sodium acetate. The test resulted in a TCEC of 54.5 meq/100 g. The difference between values obtained for this material and published values for zeolites may be attributable to the greater heterogeneity in the material used in this study, compared to commercially available materials, or to the effect of the relatively large particle sizes utilized. Batch studies. Seven batch studies were conducted using synthetic metal solutions and soil extracts (Table 1). Extract composition: The P-extract was prepared by sequential surfactant extraction of organics from a burnpit soil followed by acid extraction of metals. The pH of this solution is approximately 1.1. A number of metals and organic compounds were present in the soil. Analysis of the extract was restricted to Pb, Zn and Cu concentrations for this study. The FBH extract was produced from a firing-range soil that was oxidized with a 0.01 M CaO solution and then extracted with 0.1 M acetic acid. This was filtered through 0.5-µm Whatman No. 5 filter paper and stored at room temperature. The pH of the FBH extract was approximately 4.5. pH Control: Calcium carbonate (CaCO3) may be present in the zeolite horizon or bed. Calcium ion (Ca") is released from the exchange sites when in contact with solutions containing ions for which it is more selective, such as lead. This results in a rise in solution pH over time. Acid washing removes most of the carbonates, eliminating the need for a buffer. Batch studies were conducted using both acid-washed zeolite (AW) and unwashed zeolite (UW) for performance comparison. The UW zeolite was rinsed with distilled deionized (DDI) water to remove fine soil particles. Both materials were dried at 105°C (220°F) overnight, so that the dry mass could be determined. Column studies. Ten column studies were conducted. Because it was expected to have the best hydraulic properties, the largest particle

Jan 1, 1999