Search Documents

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By Burns Sutherland

Although some mine hoisting systems incorporating steel wire ropes on drum hoists experience completely dependable performance on the hoist ropes for many years, other rope records illustrate an erratic behaviour pattern and, as such, become a source of concern to the operator. This paper describes the causes of the difficulties most commonly encountered and incorporates methods of providing preventative or corrective maintenance. When such a program is utilized wisely, within the allowable limits of shaft time available, it can be the means of avoiding many unforeseen circum-stances and of reducing operating costs, as well as rope costs, to a mini-mum.

Jan 1, 1970

By Davidtz. John C.

INTRODUCTION The effectiveness of collector type on sulfide mineral flotation is generally determined by the amount and type of functional groups of collector molecules that interact with surface and water at the mineral/collector/water/gas interface. The final interfacial state when bubble contact takes place is preceded by chemical and physical reactions that involve these gas/liquid/solid interactions. These interactions differ not only for different minerals, solution and gas composition, but also for different collector molecules. The purpose of this paper is primarily to summarize the developments and status of short (C2-C6) and long (C12) chain, aliphatic collectors that contain three sulfur atoms in their polar function. These are trithiocarbonates (TT'Cs). For purposes of comparison, similarities in molecules containing 0, N and S are compared. Mostly short chain ionic collectors molecules of dithiocarbonates (DTCs) and TT'Cs were compared. The studies, largely bench scale flotation and plant testing, were carried out on ores containing Cu, Ni, Au, and PGM's. Studies of long chain 'ITC collectors are reported on Ni, PGM and auriferous pyrite ores containing uranium. Under starvation dosage conditions, surface activity coefficients of short chain collector molecules and interacting water were calculated. Based on the UNIFAC group contribution method of activity coefficient calculations, the Gibbs Excess Free Energy

Jan 1, 2005

By A. E. Lehman

A RECENT demand for some form of panoramic display of an important railway line, showing its branches, connections, and terri tory controlled by it, revealed to the writer the advantages of' a topographical model or relief map fix this purpose. Hitherto, maps of this nature have been used chiefly for scientific and geographical purposes, and confined to a comparatively narrow field of service. They deserve to become more popular and to have their advantages better understood. Much has been written and accomplished in this direction by Prof. Lesley, Messrs. Harden, Moulten, de Mendonca Cortez, and others; but I believe their pub lished descriptions of the methods employed in the construction of these models are confined to those used by themselves. It is the writer's aim to present in condensed form these various methods, and some suggestions of practical value as to the most economical course of procedure, as well as to mention some of the uses that may be made of the results obtained Methods of Construction.—Many different materials have been prepared and used in the preparation of relief maps, such as metal, clay, plaster, gypsum, wax, putty, Card-board, papier-mache, wood, and compositions of varions kinds, with results more or less success ful : wood, however, in the writer's experience, has been found to be by far the most satisfactory, combining the advantages of stability, accuracy and ease of handling. The following is a brief description of several of the methods used in constructing topographical models : When clay, wax, putty, compositions or materials of a plastic nature are used, the operator carries his work up from its base by means of measurements or by the eye, manipulating and shaping the material as best he can, ac cording to such features of his subject as he wishes to delineate. This process requires remarkable skill, and given this, will probably fall short even then of an approximation to accuracy; lacking essential elements of detail nil over the work and exactness, particularly in position and elevation of the most important points in the territory mapped. When either of the above mentioned materials or compositions are used, metal or wooden pins are sometimes driven into the base or level datum plane of wood, the top of these pins giving the eleva-

Jan 1, 1886

By Leonard A. Wolff

"The 1980sfor the mining industry can be characterized as the survival of the fittest. High interest rates, low commodity prices, foreign subsidized competition and decreasing ore grades have contributed to a streamlining of the domestic mining industry in the United States, leading to the shutdown of operations or large cutback of work forces. The purpose of this paper is to look at the impact of a layoff on the employees of what was once a major uranium producer in south central Wyoming, twenty months after the final layoff and mine shutdown. INTRODUCTIONDecember 19, 1985, was the date of the final of three successive layoffs over a two-month period, leading to the complete shutdown of Petrotomics Company, a subsidiary of Getty Minerals Company. The final shutdown was due to a combination of depressed U3O8 prices and the takeover of Getty Oil Company by Texaco in January 1984.The layoffs affected 104 employees and included mine personnel, mill personnel and staff. Both hourly and salary workers were involved. The operation was considered non-union, however, a few mill hourly employees were unionized. At the completion of the layoffs. only a handful of employees remained for administrative and miscellaneous functions.For Getty employees, the terms of the merger agreement provided a generous level of separation benefits. The terms that were insisted upon by Mr. Petersen, Chairman of the Board for Getty Oil, stipulated that employees receive one month of severance pay, for each full calendar year of employment up to a maximum of two year's pay. This was the forerunner of what is now commonly known as the ""tin parachute”. All but the union employees of Petrotomics received these separation benefits. Union employees were covered by their separate, less generous, contract.Much of the literature that has been published in recent months has centred around the effects of layoffs on remaining employees, or the psychological effects on the severed employee. This study will emphasize the economic impact and ramifications due to a layoff, using the Petrotomics employees as a case example."

Jan 1, 1989

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By Perring CS, Vearncombe J. R, Ho SE, Groves DI

Large Late Archaean greenstone belts in Western Australia, Canada and Zimbabwe, contain abundant mesothermal gold, volcanogenic massive base-metal sulphide, and komatiite-associated Ni-Cu mineralization. These greenstone belts are similar in many respects to convergent and accretionary plate margins found in the Pacific rim; modem environments which are cor-respondingly rich in gold and base-metal mineralization. The giant gold placer deposits of the Late Archaean Witwatersrand Basin (the world's largest gold producer) formed in a foreland or retro-arc basin; in a similar tectonic setting to much modem placer mineralization around the Pacific. Gold and volcanogenic base-metal sulphide mineralization are abundant in Late Archaean terranes and the Pacific rim because1. gold mineralization is a product of convergent margin tectonics, and 2. accretion in convergent margin orogens provides the best chance of preserving base-metal mineralization related to submarine volcanism.It is therefore likely that the abundance of gold and base-metal sulphide mineralization in the Late Archaean reflects the widespread growth and sta-bilization of continental crust via tectonic processes broadly similar to those operating in the present Pacific basin.

Jan 1, 1990

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

By Xing Jin, Dan Graffi, Glenn MacPherson, Dan Rioux

"The complexity of a modern flotation circuit makes it susceptible to disturbances such as changes in feed, ore mineralogy, equipment degradation, poor measurements and faulty instruments. Good measurements and a robust control system are critical to create and maintain a stable and optimum flotation process.This paper focuses on the development and implementation of process control applications in the flotation circuits at Xstrata Nickel’s Strathcona Mill ( referred to as the mill hereafter ) in Sudbury, Ontario. Following the path of ‘stabilize-improve-optimize’, basic controls to stabilize process variables such as flotation cell pulp level, air and reagent addition rates, cleaning-column feed and wash-water rates have been established. Factors such as best practice in pulp level and valve position measurement, feedforward control and the application of an appropriate control philosophy, have contributed to the significant reduction in process variability. For instance, standard deviation reduction of 79% for the Ni impurity in the column Cu concentrate grade was experienced and is shown. The variability reduction of the flotation circuits’ key process-variables paves the way to further improve and optimize flotation performance. A grams-per-metal unit reagent addition control scheme has been improved upon, particularly for different operating scenarios and better robustness. In addition, following significant stabilization of the primary controls and columns feedrates, Cu/Ni separation cleaning-column bias-control (cascaded to the wash-water rate) and hold-up control (cascaded to air flowrate) have been developed and tested. This strategy – from stabilization to optimization - is expected to achieve a more consistent control of final concentrate grades and improve recoveries.INTRODUCTIONFlotation is considered the most important and value-added process in the milling metallurgical plant and is still undergoing continuous evolution to treat greater tonnage and different ores (Wills, 2006). Starting over three decades ago, with the advent of on-line slurry content analysis devices, flotation automatic control has received persistent interest and a large number of applications have been reported (Thwaites, 1983, 1986 ; Mckee, 1991). Bergh and Yianatos (2011) reviewed different aspects of process control in flotation circuits and have evaluated the applicability of model predictive control to the process. Mckee (1991) analyzed the difficulty in developing lasting/robust process control applications for flotation circuits and stated that the path of stabilization-refinement-optimization would more likely lead to successful flotation circuit process control. Best practice on column process control was discussed by Bouchard, etc. where a multi-layered approach was proposed, provided that the measurement of column process variables ( i.e. bias, froth depth, hold-up, etc. ) are measured reliably (Bouchard & Thwaites, 2008). Wills (2006) stated that the best practice for flotation automatic control starts with fulfilling basic control objectives, such as stabilized flotation cell level, air flow, pH, reagent flow etc., before considering more advanced, or even optimal, control of metallurgical targets, which are more closely linked to economic performance."

Jan 1, 2013

By G. S. Scott, H. G. Turner, W. L. Kleene

It is well known that different forms of carbon show differences in chemical behavior under apparently identical conditions. It is fairly well known that these differences persist, although to a lesser degree, in a single group of carbons, such as the anthracites of Pennsylvania. It is the purpose of this paper to show the extent of these variations for Pennsylvania anthracites from actual quantitative measurements of the amount of carbon dioxide reduced under the standardized test conditions employed. As the amount of carbon dioxide reduced to the monoxide (under comparative conditions termed, for convenience, the "reactivity") is important in combustion, gas production and metallurgy, it is hoped that this paper will be a useful contribution to the store of knowledge on these subjects. In carrying out the investigation, considerable time and thought were spent in obtaining what seemed to be the best possible design of apparatus. The next step consisted in making a number of trial runs on the same sample, varying temperature, particle diameter, etc. and then outlining a standardized procedure to be followed in testing all samples. Fifty anthracites were tested. As a matter of interest, some 10 miscellaneous samples were also tested. The data show initial reaction temperatures (abbreviated I.R.T.), reaction velocity constants at 900" and 950" C., some effects of added substances, and a few additional tests designed to throw some light on the causes of differences in reactivity. The sample of charcoal, as was anticipated, proved to be easily the most reactive of any sample tested. The anthracites as a group came second. The five samples of gas and by-product cokes, obtained from five different coke manufacturers, came third, and a single sample of Rhode Island anthracite ranked fourth, with respect to reactivity as above defined. Although the five coke samples do not necessarily represent the average market coke, and five samples constitute a rather small number of samples to serve as a basis for comparisons, the fact that none

Jan 1, 1934

A small-charge rock excavation method based upon the Penetrating Cone Fracture (PCF) technique has been demonstrated to be capable of excavating the hardest of rocks. The PCF technique involves drilling shallow holes in the rock which are then pressurised at the bottom by a propellant charge device. A controlled fracture is initiated at the hole bottom comer and propagates in such a manner as to excavate the rock at an energy efficiency three to five times better than explosives. Due to the low flyrock velocities and airblast pressures realised with PCF breakage, the method may be used in close proximity to equipment and personnel and is thus ideally suited for integration into continuous hard rock excavation systems. Over the past 18 months full-scale testing of the PCF method has been carried out in mines in the US and Australia. This testing has utilised a 76 mm diameter gas injector for hole pressurisation and employed propellant charges ranging from 80 to 320 gm. In addition to extensive data on rock excavation performance, data on ground motion, dust, carbon monoxide and air blast have been obtained. These data indicate that none of the parameters associated with PCF breakage are detrimental to the development of PCF-based, continuous-excavation machines. Machines employing the PCF method may range from simple single-boom machines for secondary breakage and small precision-blasting jobs to integrated systems with several booms, continuous mucking capabilities and ground-support equipment for drifting and tunnelling.

Jan 1, 1993

By N Davies, M J. Coward, P L. Hissey

Mount Isa Mines has four mining operations in Mt Isa with the X41 and Enterprise Mines producing copper and the Lead Mine and George Fisher producing lead zinc and silver. Each stream contributes ore to their respective concentrator at a feed rate and therefore metal ratio set out by the monthly schedule. Mine Planning and scheduling lead to a sales and operating plan (S&OP) and revenue projections which ultimately derives actual revenue /tonne and therefore cost/tonne. At Mount Isa, both the copper and lead/zinc streams produce ore from relatively new operations to be blended with material from more mature operations. It is critical to accurately predict the metal contribution from each operation in order to gauge the relative performance of each mine. Development mining ore contributions are estimated and reconciled, as are stope and bench sources. Performance is continually measured and assessed during extraction and grade adjustments are made to account for underbreak, overbreak and design modifications. It is critical to not understate or overstate the contribution from one operation relative to the other as this can produce a false picture of operational performance. Identifying process improvements are key to improving the business overall. Ore from the lead stream passes 17 measurement stations and two midstream reconciliation points before delivery to the heavy media plant (HMP), where the metallurgical circuit begins. From this point two concentrates are produced. A zinc concentrate for treatment off site and a lead concentrate for further on site processing. The lead smelter takes 100 per cent of Isa concentrates as well as a contribution from BHP-BillitonÆs Cannington Mine.

Jan 1, 2002

By H. W. Parsons

Several low-temperature, dry chlorination processes for the treatment of sulphide minerals are reviewed, in a chronological order. These processes include the following: the Swinburne-Ashcroft, Baker-Burwell, Maim, Comstock-Wescott (Aldermac) and the Mitterburg Mining Process. Dry chlorination investigations at the Canadian Mines Branch (now CANMET) and the U.S. Bureau of Mines are discussed, as is a proposed process by the South Africa National Institute for Metallurgy. The techniques used in the process are discussed, as are the shortcomings, problems and failures of the methods.

Jan 1, 1978

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By Tucker A. J

An overburden blast utilising horizontal blast holes was successfully attempted at the Ulan Coal Mines during December 1991. The blast reduced operational problems and costs and improved dragline productivity in an area of that contains poorly consolidated sands and clays overlying very hard Permian strata.The fan shaped shot consisted of seven 250 mm diameter holes between 80 and 95 metres long drilled into the highwall face. The holes were loaded with ICI Powergel Gold 25606 bulk Emulsion explosive. The design powder factor was 0.15 kg/bcm for the total shot of 180 000 bcros and 0.44 kg/bcm for the competent Permian strata into which the holes were drilled. Fragmentation from the horizontal blast was comparable to areas conventual blasted. Following the success of this shot further shots are planned for this area.

Jan 1, 1992

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By Glastras M. V

The presence of arsenic in solutions which result from the processing of many sulphide minerals leads to a need to understand its speciation in aqueous systems and the reactions of those various species. This paper deals in particular with the precipitation of arsenic from aqueous solution in the form of insoluble inorganic compounds in order to remove arsenic from various hydrometallurgical process streams. The solubility and stability of the precipitates is examined. It has been found that many of the arsenic compounds presently used are more soluble than previously accepted and unstable in disposal sites such as tailings ponds.

Jan 1, 1987