Search Documents

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By A. V. Tarasov

The insufficient scientific and technical level of a number of operations in the nonferrous metals industry encourages development of new processes and equipment, including smelting in liquid bath, flame-type sparged smelting unit for combined processes, electrothermal process with the use of alternating current (PDF furnace), electrothermal processing of complex raw materials and intermediate products at nonferrous metallurgical plants, etc. One of the most important aspects for development of new processes and equipment in the Gintsvetmet Institute is their environmental safety. Special attention is paid to environmental protection measures, which is also of important economic and social significance. This refers also to a complete extent to processing of reserves of man-made raw materials and wastes available at the existing operations with the use of innovative techniques ensuring not only resource conservation and environmental protection, but also abatement of negative impact on the nature due to accumulated industrial and domestic waste, reclamation of the land used for waste disposal and recycling of nonferrous metals. Technologies and equipment developed in the Gintsvetmet Institute and based on electrothermal processes determine the prospects for ensuring more integrated usage of ores and man-made raw materials.

Jan 1, 2006

Geostatistical analysis, resource estimation and three-dimensional modelling of the gold grade distribution was undertaken using exploration drillhole data taken from the Mt Leyshon gold mine. The main aims of the project were to provide an independent estimate of the primary gold resource and to improve the estimate by better understanding the statistical distribution of gold and the establishment of more robust variograms. These criteria have been achieved by the removal of low grade sub-populations, increased sample size and access to data from the most recent drilling program. The outcome of this statistical study has led to a lowering of the sill and nugget variance of the variograms used. Distinct geometric anisotropy was identified in all the resource estimation zones and was used to model gold grade distribution.Two independent resource estimates were established from the primary gold resource, one based on a geostatistical estimator (kriging) and the other on a traditional estimator (inverse distance weighting). Both methods were compared with a contemporary kriged estimate by Mt Leyshon Gold Mines Ltd.

Jan 1, 1993

By I. E. Rosenzweig

GeophyGical prospecting by earth-resistivity methods is frequently applied to investigation of structural problems in geology. Fig. 1 indicates a scheme of the general arrangement used in these methods of measurements. The battery (or generator) E is connected with two "current electrodes" I1 and I2. The current of intensity J, supplied by this battery, passes through the earth between these elcc- trodes. A potential difference U will be measured between two other electrodes V1 and Vz, called "potential electrodes." According to the configuration of electrodes (Fig. I), the resistivity of a homogeneous soil results from the formula p — 2rca-j [1] where 1 C = -------------------------------------- a a 1 a a [2]

Jan 1, 1940

By Douglas Martinazzi

O processo de soldagem por fricção com pino consumível (Friction Hydro-Pillar Processing- FHPP) um método de reparo no estado sólido que consiste no processamento termomecânico de um pino metálico em alta rotação e inserido em um orifício criado no material a reparar. O pino é pressionado com uma força axial e o aquecimento resultante do atrito dos materiais é suficiente para garantir a plastificação dos mesmos promovendo o preenchimento do orifício e a união dos componentes. Este trabalho é centrado na análise da distribuição de inclusões não metálicas do tipo Sulfetos de Manganês (MnS) presentes em juntas soldadas produzidas por esta técnica com a aplicação de diferentes forças axiais. Micrografias da zona termomecanicamente afetada (ZTMA) foram realizadas por microscopia ótica em amostras polidas e sem ataque para registrar as inclusões. Essas micrografias foram avaliadas via análise de imagens visando a determinação de quantidade, tamanho e área ocupada pelas inclusões nas juntas em juntas soldadas. O mapeamento identificou a distribuição e o tamanho médio das inclusões em função das forças axiais. Concluiu-se que a região analisada é potencialmente crítica no que diz respeito a tenacidade à fratura, uma vez que foi observada uma quantidade considerável de inclusões fragmentadas de dimensões reduzidas.

Aug 7, 2018

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Robert E. Charles

Much has been said about digital computer control of metal and mineral ore dressing processes, but little has been done. This pa- per discusses what practical use can be made today of a digital computer in an ore concentrator and how such application can be made successfully. A hypothetical, but commercially common, grinding and flotation circuit is presented in terms of analog measurements which can and are being made in existing plants and a centralized computer control system which is reasonable in terms of today's technology. Dangers and possible disadvantages of such an approach are discussed as well as estimated benefits. Possible future benefits are presented in terms of improved control technology. Development of new measuring devices is not considered as a criterion for computer benefits. The control systems described have been utilized successfully in existing ore dressing operations. However, the degree of success or failure of analog systems is generally left to the interpretation of management rather than absolute analysis. Many factors affect the economic operation of a mineral recovery circuit such as size of facility, flow sheet design, number of operating personnel, percent of recoverable mineral in the ore body, loss to tails, and haulage rates. In existing mills where little or no instrumentation has been used, it is extremely difficult to prove or disprove the advantage of analog control systems on one mill line versus its sisters due to the lack of standards and the lack of ability to separate final products by ton.

Jan 1, 1969

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By James S. Browning

Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama. 1, 2, 3 Whereas in western North Carolina these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites.4 To a lesser extent, mica is produced as a byproduct of feldspars and spodumene.6 Past research by the Bureau of Mines has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica." This method requires thorough desliming of the ore with consequent fine mica losses. The other method utilizes an alkaline-anionic-cationic process for recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica. 8, 9, 10, 11, 12, 13 The latter process has also been successfully applied to a micaceous schist ore from California.14 This report summarizes the results of these research studies. Both of the flotation processes developed by the Bureau of Mines have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores.

Jan 1, 1969

By Sir Robert A. Hadfield

The Hadfield method of producing sound steel ingots has been the subject of a paper read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make poseible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying addi, tional heat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molten condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 1, 1914

By D. G. Mickle, H. L. Hartman

Hydraulic filling was probably first used as a means of ground support in 1864 in an anthracite mine at Shenandoah, Pa. In the nearly 100 years since that time it has gained widespread acceptance, but surprisingly little study has been made of the basic features of the process. The investigations that have been made primarily concern the design of preparation processes and transportation systems, while little attention has been paid to ensuring that the fill does its job adequately after placement. Both permeability and compressibility of fills have been studied in the laboratories of the Department of Mining at The Pennsylvania State University under the sponsorship of the Mineral Conservation Section, formed to promote efficient utilization of the state's resources. Results of these studies form the basis of this article.

Jan 11, 1961

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913

Caterpillar Inc The world's largest manufacturer of construction and mining equipment, diesel and natural gas engines and industrial gas turbines. Technology leader in logistics, construction, transportation, mining, forestry, energy and electric power generation.

Aug 1, 2013

By Gary L. Simmons

Over the past several years, Newmont Gold Company (previously Santa Fe Pacific Gold Corporation) developed a new technology for the flotation of refractory auriferous sulfide minerals which is referred to as the N2TEC flotation process. Starting in April 1997, the first commercial flotation plant utilizing N2TEC technology was successfully commissioned at the Lone Tree Mine near Valmy, Nevada. The Lone Tree flotation plant was designed to process 4,085 mt/d of ore producing 494 mt/d of sulfide concentrate. A flotation tails leach CIP circuit was added to recover cyanide-soluble gold from the flotation tails. A portion of the flotation concentrate is blended with whole ore feed to the Lone Tree autoclave, up to the limit imposed by the current oxygen plant capacity. The remainder of the concentrate is shipped to either the Twin Creeks autoclaves or the Carlin roaster for subsequent oxidation and gold extraction. This paper discusses the results achieved in the commercial flotation plant compared to pilot plant testing and engineering design flotation modeling. Capital and operating cost information are also presented.

Jan 1, 1999

By Wing G. Agnew

[This report presents the results of tests made by the Mining Division, Bureau of Mines, on the relative durability of manganese-steel drill rods and carbon-steel drill rods for use with detachable bits.]

Jan 1, 1941

THERE have always been in this world men of such keen intelligence that with their discourse they have been capable of infinite and various inventions that are as beneficial as they are simultaneously harmful to the human body. Wherefore, from day to day, we see unfolded before our eyes some of these that greatly astound our minds, and we remain so stupefied that when-we think of them we are not able to control our faculties for some time, both from considering by what necessity or purpose these men were goaded, as well as from contemplating the profound subtlety of their discoveries, which, in truth, are such that they are awarded the greatest commendation by noble minds. By following their counsels and with their aid, there have been* some astute and lever captains who have had certain pots or balls of earthenware carried by their infantry, expressly filled with compositions of powder or other unctuous liquors disposed to ignite easily. When they meet the enemy in battle and come up close to them, they try to strike vigorously with these in the first assault in an effort to throw them into disorder and to make them give way by breaking them up and drawing them out of formation. The smoke is harmful, but the fire very much more so. These are made in this way. Take the number of vessels that you have to make-it does not matter whether they are raw or baked as long as they are well freed from the moisture of the clay-and fill them a little more than half full with coarse gunpowder which has mixed in it pounded Grecian pitch and at least a third of crushed sulphur. Then pour in a covering a dito thick of strained pig fat mixed with powder. This keeps it from falling out when it is thrown and keeps the fire slower until it reaches the enemy. When this has been made, open up the pig fat a little at one side when you wish to throw it and put in a little fuse or a little good powder and apply fire, holding it in your hand until you see that the fire has taken hold well. Then throw it, choosing your time. A liquid composition is also made in a kettle in which are put pork fat, petroleum oil, oil of sulphur, live sulphur, [163] doubly refined saltpeter,

Jan 1, 1942

By Arthur M. Hartstein

The Bureau of Mines through contract with Ultrasystems, Inc., obtained gram per gram data of products formed on thermal oxidative degradation of selected compositions, both under dynamic and static conditions. Four broad classes of materials were studied! Polyvinyl chloride compositions, neoprene compositions, rigid urethane foams, and variously treated woods. Whenever possible, comparisons between pure components and composites were attempted. Thermogravimetric and differential thermal analyses were performed to gain understanding of the processes occurring and to explore the feasibility of using these analyses as a method of material identification. The toxic products detected and quantitated included HC1, H2S, CO, S02, CS2,COS, HCOOH, CH3COOH, formaldehyde, acrolein, C 6H6, chloroprene, chloroethanol, benzyl chloride, aniline, and furfural.

Jan 1, 1974

By R. D. Brittain

In order to analyze and control the transport of harmful trace-element impurities in various smelting processes, it is necessary to have fundamental information about the chemical thermodynamic properties of the pertinent condensed and vapor phases. This paper describes recent thermodynamic studies of the gaseous arsenic sulfides and of the activity of arsenic in a copper-iron sulfide matte phase. These studies were carried out by high temperature mass spectrometry and by effusion vaporization techniques, which permitted clear identification of the molecular species involved, a decided advantage in such complex systems. The nature of the results obtained and comparisons with previous interpretations will be described.

Jan 1, 1983

By Joseph L. Gillson

YOUR speaker has long sought an opportunity to review the many differences between the subject matter called economic geology and the duties of a practicing economic geologist. As the subject was taught in my student days, professors teaching courses in economic geology paid little attention to what we now call industrial minerals. Certainly they were not concerned with problems involving production and marketing, but only with the origin of such mineral deposits as the Stassfurt potash deposits; with other evaporites, such as salt, gypsum, and Chilean nitrate; with the possible modes of formation of sulfur in salt domes; and the causes of asbestiform mineralization. Of course, much time and thought was given to the mineral identification and sequence of deposition of the minerals in pegmatites. The fact that such deposits actually produced commercial feldspar, mica, beryl, and lithium minerals for sale in industry was of minor importance. These observations lead us to pause to inquire, perhaps facetiously, what is and what is not to be included in the science of economic geology?

Jan 5, 1957

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008