Search Documents

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By A. C. de Araujo, M. G. Barbosa, R. Martino, S. Gaydardzhiev

The Iron Quadrangle district is a world-class iron ore mining district in the region of Belo Horizonte, capital of Minas Gerais state, in Brazil. Many mining companies have been mining high-grade hematite ores for decades throughout the region. The mines reserves often include itabirite ores which are available in high volumes, but have lower iron grades than hematite ores and require elaborated mineral processing to meet the requirements of downstream steelmaking. Itabirite ores have acquired importance, with the depletion of high-grade hematite reserves due to their intensive mining. The objective of this paper is to propose a geometallurgical model for the processing of itabirite ores from an Iron Quadrangle deposit, which will allow predicting the behaviour of ores throughout the deposit, according to their local variations. An initial step consists in characterizing representative samples of the different ores to acquire mineralogical and textural data. Then, itabirite ores of known characteristics are processed with different techniques, in order to extract the trends and key parameters upon which the geometallurgical model is developed. At first, the model takes into account the particle size distribution and its shift during mining and screening, as well as the chemistry and mineralogy of the material. Then, using the previously identified key parameters such as iron recovery, the model predicts the composition of the processing products. Finally, this data is used to model the mineralogy and mass recovery of the products. The geometallurgical model is of great importance, as it is able to model the processing of any sampled ore throughout the deposit. The incorporation of the results in a mining block model will assist mine planning and opens new opportunities for an optimized mining schedule.

Jan 1, 2016

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By R. S. Boorman, L. J. Surges

"Ore reserves at Brunswick Mining and Smelting totalled 101(106) tonnes grading 97 grams tonne-1 silver at the end of 1981. Silver is recovered as a byproduct in the copper, lead and bulk concentrates and is lost to the zinc concentrate and plant tailings. Recovery of silver for the year 1981 was 58,5%. The loss of potential revenue is in excess of Cdn $50(106) year-1 at current silver prices and milling rates.Silver is known to occur in solid solution in galena and as tetrshedrite. Evidence indicating the identity and significance of a third silverbearing mineral assemblage is reviewed and the distribution of silver losses is detailed. Characteristics of each the carrier which may be responsible for observed distribution, including size, surface quality, liberation and composition are considered, and the third carrier is shown to have possible implications for improved silver recovery by other Canadian producers as well as by Brunswick Mining.Silver tetrahedrite tailings distributed tailings and losses occur as coarse, free and as very fine unliberated galena in losses of the third carrier are between the zinc concentrate and are concentrated in the finest size fractions. Process alternatives for enhanced silver recovery by physical and chemical means are reviewed."

Jan 1, 1983

By H Thanasekaran, M J. Mankosa, J N. Kohmuench, G H. Luttrell

"Fluidised-bed flotation has been demonstrated over the last 16 years as an effective method for improving the flotation recovery of coarse particles. This technology has been successfully deployed into the industrial mineral sector with multiple installations within phosphate beneficiation plants and potash mills. Due to the minimal mineral surface expression required when utilising this technology, more recent studies have centred on the applicability of using this HydroFloat™ technology for the recovery of coarse sulfides and base metals. Multiple approaches have been investigated to determine the best means for implementing this novel coarse particle flotation system into both existing and new plant circuitry. These include the treatment of tailings to recover values that have been lost using conventional technologies and also the direct treatment of a coarse feed, either within the grinding circuit or by use of a separate split-feed flotation approach. Recent applications of the technology will be presented along with data generated from several test campaigns and ongoing research investigations. The benefits of properly applying this technology, such as reduced power consumption and increased mill capacity will be discussed.Citation:Kohmuench, J N, Thanasekaran, H, Mankosa, M J and Luttrell, G H, 2016. The Impact of Fluidised-bed Flotation for Treating Coarse Sulfides, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 105–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Mine Dewatering for reoccupation of a flooded mine requires rehabilitation and recommissioning of shaft and sane level functions to provide safe efficient access, services and logistics, as well as securing connections with all exposed workings. The objective is the earliest secure reoccupation of the target depth horizon for minimum water pumping, consistent with an appropriate investment and optimum schedule of operating inputs to the dewatering, redevelopment, services and consolidation processes. Strategy must focus on recommissioning of relevant functions in the shaft and at stage pumping horizons, advance of logistics close to pumping and rehabilitation, management of the secured exposed workings. The progress must be systematic, sustained and integrated, and must be secured against risk and uncertainty. There must be a strategic capability to respond effectively, and manage interruptions to processes, conditions requiring higher or different resources, and contingencies which affect schedule, budget or risk profile for the continuing programme. Planning must aim to reduce or contain risk or uncertainty elements and contingencies, limit interruption frequency and severity, identify and provide the capability for efficient responses. It is appropriate to model and simulate the reoccupation analogous to a mine initial development production programme. Only minor changes to relationships and relativities of models for Capital works, Operations (Production and Development) and Services/Logistics are needed but the model for management of workings is more relevant than that for depleted workings in an operating mine because of the water and other transfers. An important difference is the unsteady state of operations which requires probabilistic modelling of availability and utilization of equipment and processes.

Jan 1, 1988

By Marcel Schlumberger

The electrical methods for surface-prospecting have been well developed in the last 20 years. The method involves, in the classic form, the sending of an electrical current into the soil, by means of two electrodes A and B, and studying the potential distribution at the surface, by measuring the difference of potential between pairs of points such as M and N. The points M and N are usually placed on a line between, and equidistant from, A and B. By increasing the distance AB, the current sent into the Earth, and likewise the distribution of surface-potentials, become influenced by regions of greater and greater depth below the surface. By varying the form and dimensions of the electrode-arrangements AMNB, called a "quadripole," one may make valuable deductions concerning the nature or thickness of beds, if one knows the electrical properties of these beds. On the other hand, if the form and dimensions of the electrodes AMNB remain fixed, the depth of penetration of currents in the Earth remains, so to speak, almost constant, although it tends to increase where the subsoil is more conductive, and conversely. Therefore, if one moves the constant-dimension quadripole over all the terrain to be Investigated, one achieves approximately a horizontal exploration. This permits a study of tilted beds or faulted horizon-tal beds. When the particular problem becomes deep, of the order of 2000 meters, or more, it is ne-cessary to Increase the distance between the current-sources AB to a length such that the work 'comes very troublesome, especially if the region is wooded. At the same time, the separation the points M and N must be likewise great (for example, one km) in order to obtain differences potential which are not too small; the measurement of potential differences across MN is then difficult because of the presence of parasitic potentials, due to a flow of telluric currents in fourth, and the order of greatness of these currents may exceed the quantities to be measured.

Jan 1, 1940

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0' plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8' plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0' occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?' plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0' plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8', formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0' plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,' no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 ' lattices at the orientations of the 0:0' boundary corresponding to the edges of 0' plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,' an experimental determination of the interfacial structure of the edges of 8' plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20'21 has been fully described in a previous paper.'

Jan 1, 1969

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955

By M. Maeda, H. Sasaki

"Precious metals such as platinum, palladium, and rhodium are commonly used for automotive catalyst converters. To recover these metals with lower environmental load and cost, exposure to zinc vapor was proposed as a pretreatment prior to acid leaching. Alloying with zinc is expected to enhance dissolution of precious metals and reduce the amount of toxic chemical agents required for the leaching. This study examined the effect of the alloying pretreatment using model catalysts. Catalysts were immersed in leaching solutions for a predefined time with or without zinc vapor pretreatment, and the amount of dissolved metals was then evaluated. INTRODUCTIONAutomotive catalysts account for large portions of the world consumption of platinum (Pt), palladium (Pd), and rhodium (Rh) (Butler, J., 2011). Because of their limited production and high prices, recovery of the precious metals from spent catalysts is obviously an important issue. A representative structure of an automotive catalytic converter can be described as a monolithic ceramic support with a honeycomb structure which is coated with porous oxides such as those of aluminum (Al2O3), cerium (CeO2), and zirconium (ZrO2) (Heck & Farrauto, 2001; Matsumoto & Shinjoh, 2007). Small particles of precious metals, originally several nanometers or less, adhere to the oxides.Typical recovery processes for precious metals from scraps are shown in Figure 1 (a)-(c) (Habashi, 1997; Yoo, 1998; Shibata & Okuda, 2002). Precious metals can be recovered by using non-ferrous smelters as Figure 1 (a) shows. Smelted along with metals such as copper (Cu), precious metals and ceramics in the scraps are absorbed into the metal phase and slag phase, respectively. Because the metals separate from Cu as anode slime in successive electro-refining, such a process can recover precious metals as co-products of Cu. However, in order to prevent negative effects on the principal process, a specialized procedure is needed. Figure 1 (b) is a specialized approach in which scraps are melted at elevated temperature with Cu called the Rose process. Here Cu works as a collector metal, and the absorbed precious metals are then concentrated by oxidation of Cu. Such a process can separate precious metals from ceramics constituting catalyst converters. Smelting at high temperature, however, requires extensive equipment as well as a high amount of energy. On the other hand, hydrometallurgical processes may be effective to separate precious metals from ceramics into an aqueous solution, because chemical agents can act on these metals selectively (Figure 1 (c)). Leaching of precious metals, however, requires strong acid and oxidizing agents because of their corrosion resistance; this makes liquid waste disposal and the large environmental load controversial. To solve the problem, a metal vapor pretreatment was proposed (Okabe, Yamamoto, Kayanuma, & Maeda, 2003a, 2003b; Kayanuma, Okabe, Mitsuda, & Maeda., 2004; Kayanuma, Okabe, & Maeda, 2004; Itoh, Kayanuma, Miyake, Kimura, & Maeda, 2005). A flow diagram of the process using zinc (Zn) vapor is shown by Fig. 1(d). Exposed to Zn vapor, precious metals are expected to form alloys which dissolve more easily than pure precious metals, thus reducing the use of chemical agents and environmental load involved with successive leaching. In previous research (Sasaki, Miyaki, & Maeda, 2010; Sasaki & Maeda, 2010, 2012), dissolutions of precious metal alloys formed by Zn vapor treatment were examined in hydrochloric acid (HCl) using an electrochemical method, and it was confirmed that these metals dissolved at higher rates from the alloys than from their pure states (Figure 2). In this study, the availability of the alloying pretreatment was demonstrated by testing on model catalysts in leaching solutions."

Jan 1, 2012

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By S. Behl

A major limitation in developing successful selective, flocculation schemes is the difficulty encountered in adsorbing the polymeric flocculant only on the desired substrate. In this paper, a correlation between selectivity of flocculant adsorption and separation efficiency is outlined, and a potential technique to achieve selective adsorption of flocculants is discussed.

Jan 1, 1994

By Frank E. Shepard

Electric power in mining-operations is now successfully applied to haulage, hoisting, lighting and pumping; and until lately, drilling was the one department of mining in which an electric source of energy had not been introduced. Drilling by electric power has been the field for much investigation and several forms of electric-drills have been tried; but in the severe service of rock-drilling many dieculties have been encountered, and the heavy cost of repairs has caused a deep prejudice against this system of drilling. In the majority of electric rock-drills previously placed on the market, two principal factors have been considered; first, a portable electric motor usually of heavy pattern, coupled to the driving-mechanism of the drill proper by means of a flexible shaft; and second, the coupling of some form of reciprocating cross-head to a piston by means of a spiral spring, the drill-bit being fastened to the piston-rod by some suitable form of chuck with fastening bolts and nuts. In this latter form of drill, the cross-head has a fixed stroke, while the piston with drill-bit attached is allowed a variable stroke through the

Jan 1, 1904

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014

By D. H. Bacon

Nearly all men are too busy with their own affairs to keep informed of the progress in other lines. From time to time we read statistics showing the development in some industry that astonish us; but the feeling of surprise soon fades: to be followed by others that likewise pass away. A short resume of what has been done in one line may be of interest. Down to late in the fifties the ore-product of Lake Superior mas handled over a mule-tram-road to Marquette; now the Duluth, South Shore and Atlantic, the Chicago and Northwestern, the Wisconsin Central, the Duluth, Superior and Western, the Duluth, Mesabi and Northern, the Duluth and Iron Range and the Lake Superior and Ishpeming railroads serve the shippers. Down to nearly 1870 a 700-ton ship was an enormous craft, the loading of which required two days; the unloading being seldom accomplished in that time. In 1871 the largest ore-barge carried 1050 toils and made twelve trips per season. Now the cargoes reach 5000 tons, the loading requiring less than three hours, and the unloading ten hours. Now the mines cover more land than was familiar to even the " timber-cruiser " when the Jackson mine was opened. The annual shipments have grown from a few thousand to 10,000,000 tons, and the ability of the mines to produce is not taxed. Lake-freights are at one-eighth, and rail-freights at one-quarter, of early prices. The deeper waterways, commodious locks and large ships of to-day are in a greater measure due to the movement of ore than to any other cause. Great savings have been made in each detail of each department. The only item of cost that has not been lessened, I am glad to say, is the money paid to men. Wages, measured by what they will buy, are as high

Jan 1, 1898

By H. F. Zurbrigg

"The Frood-Stobie Mine is by far the largest metal producer in the Sudbury area. Its efficient development was made possible by the consolidation of three mining properties that covered parts of the same ore body. They were known as the Frood Mine, the Frood Extension, and the Stobie Mine.The southwest or Frood portion of the orebody was discovered by Thomas Frood and A. J. Cockburn in 1884. Cockburn's interest was acquired by J. H. Metcalf and W. B. McAllister and patents were issued to Frood, Metcalf, and McAllister in 1884. The property was purchased by the Canadian Copper Company (lnco) in 1886.James Stobie discovered the northeast or Stobie part of the orebody in 1885. In 1886 Stobie and Rinaldo McConnell applied for the location and patent was issued in 1886. They sold the property to the Canadian Copper Company (lnco) the same year.The Frood Extension property included very little of the ore zone at surface but it covered ore down the dip from Frood. Frank Cochrane was granted title to the property in 1908 and sold it to the Mond Nickel Company in 1910. The title was transferred to the International Nickel Company in 1929 at the time of the Inco-Mond merger.Prior to 1930 the three properties produced a total of about 1 ,000,000 tons of ore from mining done during the periods 1887-1903, 1913-1915 and 1925-1929. Since 1929 the Frood-Stobie operation has produced more than 120,000,000 tons of ore, about half from open pits and half from square set and blast hole stoping. The current production rate is in excess of 6,000,000 tons per year.The principal products from the ore are nickel and copper. The by-products are iron ore, cobalt, platinum, palladium, rhodium, ruthenium, iridium, gold, silver, selenium, tellurium, and sulphuric acid."

Jan 1, 1949

By Stephen A. Swan

Bureau of Mines research has not included analyses of mining dredge safety since 1948. Because of the increasing use of dredges, 63 fatal accidents and several hundred nonfatal injury accidents involving dredges were examined. Also, 31 working dredges and 3 dredge manufacturers were visited to acquire qualitative information. Drowning accidents represented 59 pct of the fatalities and are delineated in detail. Also, countermeasures against other hazards are discussed.

Jan 1, 1985