Search Documents

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES-F. R AND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS8 GEORGE C. STONE2 J. H. JANE WAY' BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 4, 1918

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By Frank Foote, Eric J. Jette

The unusual physical, electrical and magnetic properties of the iron-nickel alloys has given rise to a voluminous literature. This work will be reviewed critically in "The Alloys of Iron and Nickel," a monograph of the Alloys of Iron Research Series, soon to be published. In what follows we shall therefore confine ourselves to those of the earlier investigations that involved the use of X-ray crystal-structure methods. The earliest X-ray work on the iron-nickel system was by Miss Andrewsl. Using the powder method of X-ray analysis purely as a means of identifying the phases present, she located a region between 20 and 30 weight per cent nickel in which body-centered and face-centered phases coexisted. No lattice constants nor details of heat-treatment were reported. Bain2 also reported some qualitative observations. McKeehan3 made a systematic investigation over the whole of the system, giving many of his alloys four and some five different heat-treatments. In alloys furnace-cooled from 900' to 950' C. he found two coexisting phases between 0.15 and 30 per cent nickel. The precision of the lattice-constant measurements was low in comparison with what can be obtained today. Even for alloys of the same heat-treatment, differences in the constants were often between two and ten parts per thousand. In regions where no change of lattice constant with heat-treatment should occur, differences of the same order of magnitude were found. Since the maximum change in the lattice constant of nickel with change of composition is only about 2 per cent of the constant for pure nickel, these variations in the constants for a given alloy cause the points to "scatter" badly about any curve that may be drawn to represent them and it is difficult to interpret such results. In spite of this, McKeehan shows that the lattice constant of nickel increased as the iron content increased. His results for the alpha-iron phase are less conclusive. Osawa4 also investigated the entire system. For alloys slowly cooled from 1150' C. and then filed into samples for X-ray analysis, he found

Jan 1, 1936

Jan 1, 1906

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By C. D. Michaelson

The memory of D. C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was immeasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War II, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling's remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential.

Jan 4, 1969

By Robson L. C

The developing countries whether they be in Africa, Asia or the Pacific, are a potentially vast market for the technologies of the more developed countries.Conducting business in the less developed countries however requires a keen understanding of their culture. A keystone of the culture of the Pacific Island Nations is kinship with the land. Without an appreciation of the implications of the land rights debate, a business venture into these countries is likely to be delayed or even doomed to failure.The European heritage, with its notions of private ownership of land, have frequently been a stumbling block to a proper understanding of the concepts of customary lands. According to our laws, ownership of land confers a number of definite rights: principally the right to use the land, the right to exclude others from its use, the right to transfer it and the right to receivF income from the property independent of use.

Jan 1, 1990

By D. L. Shenck

The Navajo Mine is exclusively a multiple seam surface coal mine located in the northwest corner of New Mexico, and entirely on the Navajo Indian Reservation (Figure 1). It is owned and operated by the Broken Hill Propriety Co., Ltd. of Melbourne, Australia. The mine began production in January 1963 with a long term fuel supply agreement with the Four Corners Power Plant. The 2175 MW nominal generating capacity of the Four Corners Power Plant consumes 8-8.5 mm tons of coal annually. With estimated reserves totaling 1.1 billion tons of strippable coal, only one third is presently committed to the generating station. As development has continued over the years, mining operations have advanced into more complex geologic areas to satisfy the utilities demand for coal.

Jan 1, 1990

By P. J. Shenon

ENROLLMENT in geological and mining engineering curricula is declining at an accelerated rate despite the greatest need for trained men ever extant in the minerals industry. Industrial and military demand is mounting, but the number of freshmen selecting the mineral field continues to fall. Estimates on the needs of industry range as high as 30,000 new engineers a year. The current deficit is more than 60,000 engineers less than the 350,000 to 450,000 which eventually will be needed. The indisputable fact is that the colleges are turning out fewer and fewer engineers despite the greatest enrollment in colleges and universities ever experienced in the United States. In 1950 a record 52,000 young men stepped out of the confines of ivy covered walls with engineering degrees in their hands. By 1951, however, the number dropped to 41,000 and present enrollment indicates a national graduating class of only 25,000 for 1952. No letup in the drop is forecast. About 19,000 can be looked for in 1953 and 1954 may reach an unhappy 12,000. It becomes clear that something must be done to attract high school graduates to engineering. One immediate possibility could be to make the course burden carried by the engineering student somewhat lighter. The prescribed curriculum in many schools is such that the student takes the path of least resistance, and instead of training for an engineering future, studies for a vocation which will allow him to learn and at the same time get at least a nominal enjoyment out of college life. Review geological and mining curricula of 20 colleges and it will be found that the engineering student is a veritable pack mule compared to a lad taking liberal arts or some other non-technical program of study. The curriculum for geological engineering at one school calls for 202 semester hr, with almost 23 hr carried per semester. Multiply this figure by three hr, the minimum supposedly to be devoted to a credit and you get 69 hr per week. With a bare minimum of 84 hr for sleeping and eating, about two hours a day remain for recreation. However, the load of other schools investigated is about 19 hr. The University of Utah requires 238 quarter hr for graduation with a degree in geological engineering, while requiring only 183 quarter hr for baccalaureate degree from University college, Utah's liberal arts school. It can be stated with a measure of surety that the same proportions exist in other universities. The first step would be for ECPD to review its requirements for mining and geological engineering. It must recognize that mining and geological engineers operate in a specialized field, as do other types of engineers. Although a geological engineer may not design a bridge, as pictured by the ECPD Committee on Engineering Schools, his field of design calls for similar engineering precision, a knowledge of materials, construction methods, economic considerations, and financing. Six schools have been accredited by the ECPD. What is the basis for approval and can the requirements be modified and still be kept in line with the needs of the geological engineer? Course work from school to school varies with the exception of mathematics, chemistry, and physics. Even in those courses the not inconsiderable variation lends dubious creditability to the mean. One accredited school requires 7 1/3 semester hr of chemistry, compared with 24 hr required by another, making an average for the six schools of 17 1 /3 hr. Required credit hr in mechanics ranges from 4 to 18 and in surveying from 2 to 15. Several non-accredited schools require more hr than do the accredited schools in some courses. Why is the engineering student forced to carry such a back-breaking load? The answer is of course fairly obvious. He is irrevocably set apart from the rest of the student body because of the nature of his life's work. He is training for a place in a world where technology is becoming increasingly involved. He must be prepared to do a job now-and not later. Mining and geological engineering require the same essential backgrounds as other engineers, and more. The "more" is a knowledge of mining methods, metallurgy and geology for the mining engineer. The geological engineer must know in addition, mineralogy, petrography, and geophysics. The load is compounded finally by the addition of liberal arts courses. Should anything be done to relieve the situation? Today's engineer must be a whole man, capable of handling the tools of communication and with an understanding of the economics of industry. He must be able to write clear simple English, and he must be man who can think from some other position than bent over a work table. He must be aware of the history of his country and to some extent that of the world. Not all schools share this view. Only two of the accredited schools require history courses. However, five of the non-accredited schools make it mandatory. Four accredited and five of the nonaccredited schools require economics. Courses in mathematics, physics, and chemistry are fundamental in engineer training. The average for the accredited schools could serve as a guide in

Jan 1, 1952

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

By Edgar Newhouse

THE lead smeltery at East Helena, Mont., controlled by the American Smelting & Refining Co. since 1899, has been in continuous operation for the past 25 years. Most of the old smelting and roasting practices have been superseded by newer and more modern methods, but on account of the difficulties involved in changing the original construction, some of the methods in use of handling materials are not the most modern. This plant, however, is particularly interesting as being one of the few essentially lead smelteries in the United States. At Federal, Ill., Collinsville, Herculaneum, and possibly other places, similar work is being done, but it is doubtful whether any of them produces as' much lead as the East Helena plant, whose monthly production averages 6,500 tons. The situation, 5 miles east of Helena, is convenient to both the Great Northern and Northern Pacific railroads, while the electric power is obtained from Canyon Ferry, 12 miles east on the Missouri river. Local quarries supply the requisite amount of lime rock, Which the contracts require to be crushed to 5 in. Of the 450 men on the monthly pay roll, a census showed 200 Austrians, 110 Americans, and 30 Italians, the balance being made up of miscellaneous nationalities. The ore supply is mainly derived from the Coeur d'Alêne mines in Idaho, and consists of crude ore, coarse and fine concentrates, middlings, and slimes. About one-half of the total output of the Coeur d'Alêne camp is sent to East Helena. An average analysis of these ores gives approximately 40 per cent. lead and 11 per cent. sulphur. Local shipments, varying, from month to month, are mostly highly siliceous gold and silver ores carrying little lead. Small shippers, leasers of old mines, and prospectors are very numerous throughout Montana, and it is the policy of the company to encourage these men by every possible means, including the free sampling and analysis of their ores and aid in the development of their mines and prospects whenever their results show promise.

Jan 8, 1914

Jan 1, 1956

By A. R. Zambrano

Equations for Power Draw, Capacity, and Work Input for predicting the performance of industrial grinding mills are derived based on torque measurements obtained in a laboratory instrumented mill. These derivations are based on mechanical principles and on the first order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express Work Input as Work Index, W;, times a Particle Size Function. These laws are only particular cases of more general expressions having the Particle Size Function raised to an exponent, the Work Exponent We. Case studies illustrate the excellent prediction of the W;-We models, compared to the three mentioned laws.

Jan 1, 2001

By E. P. Abrahamson II

The effect of transition element binary solid-solution additions upon the recrystallization temperature of vanadium has been investigated. Cr, Fe, Co, Ni, Mo, Ru, Rh, Os, and IY lower the recrystallization temperature, while Ti, Mn, Zr, Cb, Pd, Hf, Ta, W, Re, and Pt raise it. The majority of elements have their greatest effect in less than 0.15 at. pet. Both the rate of change of recrystallization temperature with atomic percent solute and the limit of initial linearity are found to Correlate with the free atom grozdnd state outer electron configuration of the sollte element. THE work of Abrahamson and Grant1 and Abraham-son and Blakeney2 has shown that the solute's elec- tron configuration appears to be a prime determinant of both brittle-to-ductile transition and recrystallization temperature in dilute binary alloys. It has also been shown by Abrahamson3 that the limit of linearity, i.e., the limit of initial linear change of recrystallization temperature with atomic percent solute, is also a function of the electron configuration of the solute in iron base alloys. Because of the systematic nature of the solute electron configuration correlation, it is to be expected that some systematic variation might be observed upon changing the solvent. Thus, this study of recrystallization in vanadium base alloys is the first of a series aimed at defining the role played by the electron configuration of solute in determining the recrystallization characteristics of dilute transitional alloys. PROCEDURE All alloys were made using 99.8 pct V containing 0.011 C, 0.024 N, 0.08 0, 0.006 H, 0.035 Ta, and

Jan 1, 1962

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993

By M Littlefair, D Gribble, R Rounsley, I Te

Low-density explosives (LDE) have applications where the explosive properties of ANFO are not well matched to the rock. In particular, rocks that are of low strength and/or well fragmented in situ. Dyno Nobel Asia Pacific (DNAP) has developed a new LDE, BlastLiteTM, which can be used as a cost-effective replacement for ANFO with excellent detonation characteristics. The product is based on ANFO with the addition of a bulking agent. The key to the product lies in the ability of the bulking agent to form a homogeneous blend with ANFO without the need for any emulsion matrix to bind the product together. This results in an LDE of low cost and high weight strength compared to existing commercial LDE products. The product has been trialled extensively and has proven to provide results that are equivalent to, and often better than, ANFO with reduced powder factors. This paper details the laboratory development and results of field trials for DNAPÆs LDE solution: BlastLite.

Jan 1, 2004

By S. K. Kawatra

The use of inferential particle sizing for a closed wet grinding circuit control has been practiced for several years. This paper presents a review of some inferential sizing equations developed for pilot and industrial plants using regression analysis. An analytical development is then presented showing how the general inferential sizing model arises from the nature of the classifier model. The relation between the general sizing model and the individual equations is then discussed.

Jan 1, 1982

By R. Maddi, I. R. Kramer

The delay time for the initiation of slip was studied in single crystals of a brass, aluminum, and ß brass. A delay time for slip was found in ß brass when the specimens were tested below room temperature; however, one was not found for a brass or aluminum. A general theory for the existence of the brittle transition temperature is proposed. A LTHOUGH a considerable amount of effort has A been devoted to the study of the deformation and fracture of single crystals, the vast majority of the work was concerned with static tests or with tests carried out at relatively slow strain rates. The necessity for the study of a possible incubation time for slip becomes apparent when the various theories which have been postulated for the elucidation of the mechanism of slip are considered. The existence of an incubation period would strongly indicate that slip occurs by a process of nucleation and growth; whereas the absence of an incubation would present rather convincing evidence that slip occurs by a cataclysmic process. In addition to shedding light on the process of plastic deformation, an understanding of the early stages of plastic deformation may be helpful in finding an explanation for the brittle behavior of the body-centered metals under certain conditions. It is well known that these metals, such as iron, molybdenum, tungsten, ß brass, etc., will become brittle as the test temperature is lowered or the strain rate is increased. In spite of the fact that this subject has received considerable attention since the turn of the century, no adequate theory exists today which explains the phenomenon. In the ductile temperature range the metal breaks with a "fibrous" fracture after considerable slip has taken place. In the brittle temperature range the metal fails essentially by cleavage on the {loo) planes: however, some plastic flow is always present even in the most brittle fractures. It is possible, as will be explained later, to ascribe this brittle behavior to the length of the incubation time for slip. Clark and Wood,' using polycrystalline metals, showed that a delay time existed for the yield point in mild steels and that the delay time depended upon the applied stress. These authors stated that the delay time was observed only with those materials for which the stress-strain curve showed a definite yield point. In their work only the mild steel specimens exhibited a delay time at the yield point, while the other materials studied-type 302 stainless steel, SAE 4130 normalized steel, SAE 4130 quenched and tempered steel, 24s-T aluminum—did not show a delay time. These authors' in an extension of their work, found that as the temperature was lowered the delay time was increased. It is, then, the purpose of this investigation to measure or to set an upper limit on the delay time for plastic flow in single crystals of a brass, aluminum, and ß brass. The delay time will also be studied as a function of temperature. The incubation time may be measured by determining the length of time the specimen will support a stress without slip occurring when the stress is greater than the static critical resolved shear stress. In order to accomplish these measurements use was made of a pendulum which was so designed that a single crystal specimen could be placed at various positions along its length. When a pendulum is struck by another pendulum of the same length, an elastic wave is transmitted down the bar with the velocity of sound in the material and is reflected from the far end of the bar. The reflected wave then travels back and unloads the stress until it reaches the impacted end of the bar and the two pendulums separate. The length of time that the specimen is subjected to the stress is equal to the time it takes for the stress wave to travel twice the distance from the specimen to the end of the bar. The stress applied to the specimen is governed by the velocity of impact of the two pendulums. The stress at which the specimen first suffers plastic: deformation was determined in these experiments by examining the specimen under the microscope for the first appearance of slip lines and by measuring the residual strain after each impact. In these experiments the critical resolved shear stress was approached from the low stress side and no attempt was made to determine it exactly. To determine it exactly, it would have been necessary to find that stress at which slip would have just started. However, since the stresses were increased in rather small increments the critical stress is believed to be approached rather closely, as will be seen from the experimental results. The critical stress will be taken as the highest stress obtained before the onset of plastic deformation. The stresses

Jan 1, 1953