Search Documents

By Alden B. Greninger

In a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form {133}. In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form (110), and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices arc body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc were deformed and examined micro-

Jan 1, 1938

By D. Harris, M. Osterberg

This paper examines the economics of acquiring mineral exploration rights by royalty-rate bidding when the royalty basis does not provide for full cost recovery. Bidding takes place prior to exploration and the documentation of actual tonnage and grade. Consequently, it increases considerably the risk to exploration capital when the fraction of cost recovered is small and the product price exhibits large fluctuations. Price and grade risk are demonstrated on a 360-Mt (400-million-st) porphyry copper deposit by Monte Carlo simulation of discounted-cash-flow analysis. Copper price is modeled as a stochastic price process, and costs are based on US Bureau of Mines cost models. When both grade and price risk are considered, the probability for a negative NPV is 0.54, given a royalty rate of 5% applied to a basis that allows the recovery of costs up to 50% of product price. Investment risk could be considerably reduced by defining the royalty basis to allow greater cost recovery. Although such a basis would require society to share in the risk, society would benefit from greater resource development.

Jan 1, 2000

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

Jan 1, 1912

By M. Brozek

The particle settling velocity is the argument of separation in such processes as classification and enrichment in jigs. It characterizes material forwarded to the separation process and belongs to the so-called complex arguments because it is the function of particle density and size. i.e. the function of two simple arguments. The affiliation to a given subset is determined by the values of two mag-nitudes and the distribution of such argument in a sample is the function of distributions of particle density and size. The paper will present a method of determining the distribution of settling velocity in the sample of spherical particles for the turbulent particle motion in which the settling velocity is expressed by the Newton formula. Because it depends on density and size of particle which are random variable of certain distributions, the settling velocity is a random variable. Applying theorems of probability, concerning distributions of function of random variables, the authors will present general formula of probability density function of settling velocity for the turbulent motion and particularly calculate probability density function for Weibull?s forms of frequency functions of particle size and density. Distribution of settling velocity will calculate numerically and perform in graphical form.

Jan 1, 2014

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By R. J. Pindred

In his paper, Davis presents an overview of risk. He also introduces the Capital Asset Processing Model (CAPM) as a foundation for selecting the appropriate discount rate for a mining project. While applying portfolio theory is more defensible than the ad hoc adjustment of discount rates, the CAPM is not a panacea.

Jan 1, 1995

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By George M. Schwartz

WHEN reviewing the progress made in mining geology for the year 1953, one might say that not much has been accomplished and, indeed, in a subject such as economic geology not much progress should be expected in the 10 months of the year which elapsed before this article was prepared. This seeming lack of progress, however, disappears when the facts are investigated a bit. There undoubtedly are more economic geologists at work than ever before. It is probably not an exaggeration to say that more geologists are now employed by a single company in the Lake Superior district than were employed in the whole district 20 years ago. In most mining districts geologists are busy with numerous problems of production, development, and exploration and some give an occasional thought to the scientific problems of the science, or rather the art, of mining geology. In fact, this very intense activity of mining geologists is one reason why progress seems slow; they do not have time to write up results of investigations. There is also a great amount of work being done which is not released because of company policy. Conditions have improved very much in recent years but mining corporations, in general, have some distance to go before attaining par with the petroleum industry in this respect.

Jan 2, 1954

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985

By P. K. Koh

Isothermal salt bath annealing of 0.014-in. thick 3 pct Si-Fe sheet was conducted at temperatures ranging from 927" to 1260°C in order to investigate the grain-growth behavior. Within the temperature range studied normal grain growth did not take place; instead nucleated grain growth prevailed. The nucleation frequency was found to increase with the annealing temperature, with corresponding decrease in grain diameter of ultimate secondaries after long-time annealing. Large secondaries grown by low-temperature isothermal annealing are essentially of (110)[001] orientation, and the (110)[001] texture is strong. The relatively small secondaries grown by high-temperature isothermal annealing also have orientations near (110)[001] as an average but widely scattered; thus the amount of (110)[001] texture is found to decxease with isothermal annealing temperature. Grain growth and texture development at various annealing temperatures can be described by families of sigmoidal curves with the time axis. ThE cube-on-edge (110)[001] texture and predominating large secondaries in fully annealed 3 pct Si-Fe are customarily produced by a 1100°C annealing of a primary recrystallized sheet. On annealing the primary recrystallized sheet above the temperature at which secondary recrystalliza-tion starts May and turnbull' have demonstrated that secondary grains decrease in size as the temperature is increased. The phenomenon was attributed to a decrease in the (G/N) ratio where G is the growth rate of secondary grains and N is their nucleation frequency. In addition, the growth of grains in orientations rather far from (110) [0011 occurred. The present investigation is devoted to detailed rate studies of the same phenomenon. Mi-crostructure, magnetic anisotropy, and texture data were obtained on strips of 3 pct Si-Fe isothermally annealed for various lengths of time in a BaC12 salt bath at temperatures ranging from 927' to 1260°C. The texture results are reported elsewhere.2 EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon-iron strip (3.16 pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Metallo- graphic studies indicated complete recrystallization. In order to provide a protective atmosphere and to obtain a rapid rise to an elevated temperature, a BaC12 and NaCl fused salt bath was used to heat samples isothermally at temperatures from 927" to 1260°C for various lengths of time. Torque magnetometer measurements were made on 1-in.-diam disc specimens before and after annealing, since magnetic torque curves supply information on textures and texture changes. Surface layers of the strip samples were polished and etched to reveal the grain structure. The diameters of grains were measured from micrographs at X100. The average value of diameters of matrix grains was established. Individual grains in the micrograph were cut out separately along grain boundaries. These grains were classified either as matrix grains or growth grains. The percent weight of growth grains in the cut-out patterns was reported as percent growth. Manv of the individual grains in the annealed samples were large enough to be X-rayed with a 5-mil beam for Lauegrams. Complete (110) pole figures were obtained for the primary recrystallized structure and short-time annealed structure with CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and ~ruce.~ Both the X-ray optics and the technique for pole figure differed slightly from those adapted previously.4

Jan 1, 1960

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By K Johnson, G Morrison, N Lisowiec

The Mount Wright gold deposit is located near the town of Ravenswood, ~90 km south of Townsville, in north Queensland. The deposit has been mined by underground methods since 2006. It produced approximately 138 koz Au in the 2011 - 2012 financial year and has a total endowment of approximately 1 Moz Au. To facilitate near mine exploration, a re-logging campaign of 600+ diamond and RC drill holes was recently conducted, resulting in a revised three-dimensional (3D) geological model and improved understanding of the ore controls and the mineralised system. The deposit is within a Permo-Carboniferous breccia complex approximately 350 m diameter and more than 1200 m deep. It consists of early peripheral granite-rich breccia, polymict breccia, a rhyolite spine and a late tuffisite (fine-grained milled breccia) pipe. The rhyolite spine is approximately 60 m + 250 m + at least 1200 m deep and is zoned with massive, flow-banded and breccia phases that are in part gradational with the other breccias. There is extensive sericitic alteration centred on the tuffisite and rhyolite units and fading out into the shallower and peripheral polymict and granite-rich breccias. There is also a broad pattern of metal zoning with elevated Pb-Zn ¦ Ag in the upper 400 m, Au-Cu-Bi below 400 m fading out below ~850 m, and a poorly defined deep Mo-W-Te-Sb anomaly. The majority of the Au ore is between 400 and 850 m below the surface in the rhyolite spine. Below this, Au mineralisation is less coherent, and more localised in the margins of the rhyolite and in the adjacent tuffisite. The developing model is that the ore is not confined to or necessarily directly genetically related to the rhyolite spine, but is driven by other phases of intrusion that also generated the tuffisite pipe. This model is being used to generate additional drill targets away from the present mine development.CITATION:Johnson, K, Morrison, G and Lisowiec, N, 2013. Advancing near-mine exploration with an updated geological model for the Mount Wright gold deposit, Queensland, in Proceedings World Gold 2013 , pp 469-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Mt. Whaleback is in the Pilbara region of Western Australia approximately 1200 kilometers north of Perth, the State capital. In this deposit the Mt. Newman Joint Venturers are mining ore reserves totalling 1500 million tonnes of high grade hematite averaging 64.0% Fe. In addition to Mt. Whaleback, 38 ore bodies have so far been identified outside Mt. Whaleback on the Company's remaining 75,000 hectares of lease area. These ore bodies contain major tonnages of iron ore. Extraction at present is planned at a rate of 37 million tonnes per annum at an ore-to-waste ratio of approximately 1 to 1.4. The ore is railed north to Port Hedland on the Indian Ocean where the different products are screened, crushed and blended prior to shipping. The purpose of this paper is to acquaint the reader with the facilities installed in the Mt. Newman operation to form a background to the sampling techniques employed, describe the precisions which were achieved in experiments conducted February through June, 1976 and also to assess the degree of blending which takes place during the various processes and to put a quantitative measure to the degree of blending. There have been many excellent papers written on the more theoretical aspects

Jan 1, 1976

By Sanja Zlatanic, Michael P. Della Posta

New York State’s Metropolitan Transportation Authority (MTA) has undertaken the largest transportation project in New York City. The East Side Access Project (ESA) will introduce MTA’s Long Island Rail Road (LIRR) service to the East Side of Manhattan, to a new terminal located beneath the existing, landmark Grand Central Terminal(GCT). Construction of the Manhattan Segment of the project will affect overlying operating facilities of two other MTA entities, Metro-North Railroad (MNR) and New York City Transit (NYCT) and major Midtown Manhattan buildings. The paper describes the evolution of the GCT concept at Manhattan from a shallow alternative proposed by a Major Investment Study (MIS), that would require extensive underpinning of multi-story buildings and have considerable impact on MNR and NYCT operations, to a deep alternative with lesser risk and potential for disruption.

Jan 1, 2001

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

NEW YORK LOCAL SECTION Executive Committee L. W. FRANCIS, Chairman WILLARD S. MORSE, Vice-Chairman THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y J P. A. MOSMAN, Treasurer Louis D. HUNTOON Since the annual meeting in February, the New York Section of the Institute has held three meetings. The meeting-on March 10 was held in conjunction with the American Society of Mechanical-Engineers and the American Electrochemical Society, at the Engineering Societies Building. The papers of the evening were devoted to records of progress in the Processes for the Photographic Reproduction of Natural Colors. The speakers of the evening were F. E. Ives, one of the earlier workers in color photography, Westley Allison, C. W. Robinson, George F. Clyfton, John B. Taylor, and Henry Hess. The April meeting was held on April 22 at the Institute headquarters, and the topic for discussion was Sanitation in Mining and Metallurgical Work. The principal paper was by J. W.. Luther, chief surgeon of the New Jersey Zinc Co. This was followed by a similar paper by Charles L. Close, secretary of the Welfare and Sanitation Committee of the United States Steel Corporation, and by an account of the sanitation work done in Cuba by the Spanish-American Iron Co., which was read by the Chairman, in the absence of Charles F. Rand. Following these papers general discussion was indulged in.

Jan 6, 1914

China has been producing gold for more than 4000 years with gold production increasing substantially since the 1980s, from about 25 tonnes in 1980 to some 160 tonnes in 1998. More than 80 per cent of the gold production is from East China. However, complete information on eastern China gold has been rarely reported internationally. This is a general overview on the tectonics and metallogeny of gold deposits in East China. The geology of these gold deposits is compiled mainly from data and information reported in China, and is also based on the authorÆs work in China from 1974 to 1986 and a recent visit to China.

Jan 1, 1999

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005