Search Documents

By R R. Lovel

In this paper, life cycle assessment methodology has been used to assess the variations in water use associated with different metal production and processing routes and provide insights into the value derived from water usage in the minerals sector. Using water consumption data derived from the literature it has been shown that the æcradle-to-gateÆ water consumption (or embodied water) for production of the various metals considered in the study ranged from 2.9 m3/t for steel up to 252 087 m3/t for gold. The results largely reflect the grade of the initial ore used to produce each metal, and can be approximated by the following equation:W = 167.7 G - 0.9039 where: W = embodied water (m3/t refined metal) G = grade of ore used to produce metal (per cent metal) The study showed that indirect water consumption in the metal production life cycle, in particular that due to electricity generation, can make a significant contribution to the embodied water value, eg aluminium production. When expressed in terms of m3/t ore, the results for all metals considered indicated that the embodied water is roughly, on average, three times the water consumption of the mining and concentration stage. It was also shown that the economic value per m3 of water consumed for the minerals industry exceeds that for the agricultural and industrial sectors, supporting the view that allocating water resources to the minerals industry has a strong underlying economic basis. Water reforms currently taking place in Australia aim to address issues such as competition for water access, reduced security of supply and increase in cost. Consequently the minerals industry, along with others, can be expected to come under increasing pressure to reduce fresh or raw water use and to integrate water use across sectors. While water recycling is an obvious candidate to help reduce water consumption in the minerals industry, issues such as water quality, among others, will influence the extent to which this can be achieved. In addition, wastewater volumes can be minimised using techniques such as pinch analysis to establish and use the minimum water requirement for the process. The use of dry or near-dry processing technologies, for which the demand for water is small or zero, may be a more radical solution to the water consumption problem; however, it is possible that the introduction of dry processing would bring with it a new set of problems, including dust.

Jan 1, 2006

Review of the mining legislation in New Zealand has coincided with a number of radical changes. These include a redirection of economic management towards a more open and competitive economy; major reform of the state sector aimed at greater efficiency, transparency and accountability; a new environmental administration; and a fundamental review of policy for management of natural and physical resources. These changes provide an opportunity to develop a consistent and coherent approach in the minerals and related statutes that will achieve objectives of economic efficiency, equity, practicability and good environmental management.

Jan 1, 1987

Transport infrastructure constitutes, since always, an essential link between regions, countries and continents, for economical, commercial and human purposes. Permanently growing mobility needs, which are encountered in the whole world, lead to a more and more clear necessity to increase and modernise these transport infrastructures, as well in quantity as in quality, for all transport modes, and for all what is able to be transported, from people to consumption goods and energy. With only very few exceptions, transport infrastructure achievements have for long been the concern of the sole public authorities, at the various levels, which put them, mostly free of charge or at very low cost, at the disposition of the user or the customer.

Jan 1, 1999

By Edward DeLilla

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to increase productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: -Prudent engineering. -Proper planning. -Realistic feasibility studies. -Effective specification. -Thorough training of the mine personnel.

Jan 1, 1994

By Alejandro Freyre

Anteriormente metales como el berilio, zircofonio, hafnio, litio, se consideraron como metales raros. Sin embargo, son abundantes en las formaciones geológicas profundas. En ese sentido, el presente texto señala la nueva clasificación desde el punto de vista de la industria nuclear. De acuerdo a ello, se divide en dos grupos: en el primero, están los minerales o elementos desintegrables como el Uranio, Thorio, etc.; mientras que en el segundo, están los minerales o metales estructurales, el Zirconio, Hafnio, Berilio, Litio, etc. Son denominados estructurales porque intervienen, ya sea como auxiliares directos en el proceso de la desintegración emitiendo o subdividiendo iones.

May 1, 1955

Jan 1, 1915

By Thomas T., Read

IN this survey of the progressive development (of education for the mineral industries throughout the United States, the review of .the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. Philadelphia Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1852, when the Pennsylvania, Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1856-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By G. L. Anderson

The critical importance of wire rope integrity to the mining industry has led to the creation of standards for the retirement of wire rope as well as to the development of electromagnetic devices and procedures that would allow wire ropes to be tested against these standards without destroying them, The U.S. Bureau of Mines (USBM) conducted research to evaluate these devices by measuring loss of metallic cross-sectional area and the number of wire breaks, or local faults. The intent was to define the extent to which the technique can identify degradation within the rope, e.g., broken wires, corrosion, and wear. Experimental results showed that instrument sensitivity depended on a number of factors, including rope diameter, placement of sensors, location and characteristics of flaws, rope speed, and tension on the rope. The experiments also demonstrated the importance of having an elongated recorder trace and a properly trained and experienced operator to interpret overall results. A design of a rope and test procedures for use in laboratory evaluation of instruments have been recommended by the American Society for Testing and Materials Committee E07.07.10, Wire Rope Applications. The USBM is working through this committee to develop standards for an electro-magnetic method of wire rope inspection.

Jan 1, 2010

By Thomas E. Ban

D-LM at Mobile The qualified success of iron ore pelletizing processes has influenced considerations for production of highly beneficiated fur¬nace charges. Such beneficiation would necessarily involve some forms of chemical and perhaps thermal conversion for production of prereduced pellets, preheated pellets, precalcined pellets, and perhaps pellets which contain all of the above features as preheated, prereduced, precalcined products. This type of furnace burden will be adapted within a new ironmaking process to be activated commer¬cially during the latter part of 196$ in Mobile, Alabama. This process will integrate a new pelletizing system with an electric smelting furnace and the pellets will be comprised of a composite charge blended from metallurgical proportions of iron ore, coal, and limestone. The plant as designed and constructed by McDowell¬-Wellman Engineering Company will feature the D-LM process and will be owned by McWane Cast Iron Pipe Company. It is significant to

Jan 1, 1968

By C. P. Watson, R. E. Collom

Various chapters already written in the history of development of the North Dome of Kettleman Hills are monotonoysly identical in the one underlying' theme of conservation of oil and gas. Discovered on Oct. 4, 1928, by Milham Exploration Co. with its wildcat Elliot No. 1, the field has been subjected to practically every modern form of production restraint in the name of conservation. The record thus far developed shows that conservation was had for a time, at a price; and that unitiza-tion must be blessed by single ownership or 100 per cent participation to be effective. In fact, incomplete unitization places a heavy handicap upon its participants in the competitive development that follows. Shut-in Agreement of July 25, 1929 Not long after discovery at Kettleman but after the Continental Oil Co. and the Standard Oil Co. had completed several producing wells in the discovery group, came the so-called Shut-in Agreement negotiated at the instance of the Department of the Interior. This agreement became effective July 25, 1929. The fundamental purpose of the agreement was to prevent bringing on production of some 30 wells then being drilled and forestall a flood of Kettleman oil on the market. A cooperative scheme was developed whereby wells in the discovery group would continue to produce. Two of them could not be shut in. Drilling wells would be completed to a water shutoff in top of Temblor and operations suspended. Producing wells would contribute the value of 10 to 25 per cent of their production to the owners of suspended qualifying wells. The percentage rate of drainage contribution was left to a committee or umpire. Some acreage was not placed under the agreement. This same acreage later did not come into the Kettleman Unit Agreement. Several wells on this acreage did not contribute to the drainage fund. The total amount of oil produced during the 17 months of the shut-in agreement, by Milham, Continental and Standard from wells in the discovery group, was 5,297,262.22 bbl. The total amount paid out in "drainage" contributions was $2,046,048.18, representing sales value of 1,266,044.06 bbl. of oil.

Jan 1, 1937

By A. J. Jacobs, G. Katz

MANY of the studies of intermetallic compounds containing uranium were performed during the early 1940's under the aegis of the Manhattan Project. Subsequently, much of this work was declassified and published after 1949. In some instances this early work, completed with relatively impure materials, represents the only source of X-ray diffraction powder data available in the literature. In the case of the intermetallic compound U,Fe some discrepancies in the powder pattern exist in the literature. Since this compound has been prepared in this laboratory, it is believed that the publication of the indexed powder pattern would help clarify the conflict in the literature. In studies of the U-Fe system, Gordon and Kauf-mannl and Grogan and Clews2 independently reported the intermetallic compound U,Fe in 1950. The crystal structure was described by Baenziger, Rundle, Snow, and Wilson3 in 1950. It is isostructural with U,Mn, U,Ni, and U,Co and crystallizes in a body-centered tetragonal lattice. The lattice constants determined by Baenziger et al. are: giving an X-ray density = 17.7 g cm-3 for 4 mol per unit cell. The compound used in this study was prepared by melting a stoichiometric mixture of the constituent metals in an argon-arc furnace using a nonconsum-mable tungsten electrode. Before the argon of 99.98 pct purity was introduced into the furnace, it was passed through CaC1, to remove water vapor and afterwards through a stainless steel tube containing calcium turnings heated at 600°C for the removal of nitrogen and oxygen. The purity of the uranium used was better than 99.9 pct and that of the iron was 99.97 pct. Before and during melting a zirconium getter was used to further purify the argon atmos-

Jan 1, 1962

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

By D. E. Nash

Environmental compliance programs for mining companies are not only important management tools, but can deflect serious civil and criminal penalties if violations of environmental laws do occur. The paper discusses the legal foundation for such programs and their basic structure.

Jan 1, 2001

Discussion of the paper of JOEL H. WATKINS, presented at the New Fork meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 391 to 411. H. Rims, Ithaca, N. Y.-It is interesting to contemplate to what extent the American pottery industry would be affected in case the English supply of china clay were shut off for a considerable period of time. The English deposits are very large, and are worked on a most extensive scale. They are more easily and probably more cheaply worked than our American deposits, which are of vein-like nature. The American producer of washed clay is not always as careful as the foreign miner and washer of this material, although he has improved in recent years. Our American washing plants are, furthermore, not as economical of material as it seems to me they might be, for the reason that more or less of the finest clay is often allowed to overflow, due to insufficient settling tank capacity. This fact is often shown by the milky character, of the streams into which the waste water is discharged.

Jan 5, 1915

By J. N. Hobstetter

It is widely believed that the nucleation of phase transformations in solid metals is accomplished by some type of local atomic fluctuations in the parent phase which arise from spoutaneous difiusion in the metal or alloy system. Under appropriate conditions, these fluctuations are believed to be stable in the sense that the free energy of the entire system is lowered if the fluctuations, or nuclei, grow. Under other conditions they are thought to be unstable in the sense that the free energy is lowered if they redissolve. The criterion for stability is usually taken as the size of the fluctuation. This view has been rationalized by Beckerl in terms of the free energy released by the volume of the nucleus and the free energy associated with the formation of a new surface surrounding the nucleus. The qualitative result of this reasoning is shown in Fig I where the changes in free energy for the surface and volume effects are plotted together with their sum against the radius of the nucleus. There is evidently always a critical size r, beyond which the release of free energy which is proportional to the volume always dominates the increase of free energy which is proportional to the surface area. Borelius2 has also attempted to rationalize the stability criterion for binary alloys, but in terms of the internal concentration of the fluctuations. He has found that, if surface energies are entirely ignored, the fluctuation must still reach a critical concentration if it is to become stable and avoid subsequent dilution. Although the Borelius theory fails to predict many observed nucleation phenomena such as the vanishing of the nucleation rate at the critical temperature, the major premise must certainly be valid. In this paper a reconciliation of the Becker and Borelius views is made by means of a search for nuclei which are at once stable with respect to both size and internal concentration. The increase in free energy per mole accompanying the formation of a nucleus which is just stable, AF., is independent of the path whereby the nucleus is brought into being. It is thus appropriate to seek critical nuclear attributes without reference to the fluctuation mechanism. The rate of nucleation, however, cannot be treated without a detailed understanding of the exact fluctuation process which produces stable nuclei. In this and succeeding papers the purpose will be to find the size, shape and internal concentration of the stable nucleus which is formed with a minimum increase in free energy in a wide variety of systems. The Nature of the Nucleus It is necessary ti have rather detailed knowledge of the nature of a nucleus if AF, is to be computed. Fortunately, enough facts are known or suspected about the nucleus to make possible a detailed analysis. X ray diffraction studies have shown

Jan 1, 1949

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By Paul W. Johnson

Chemical mining is the in situ extraction of metals from ores located within the confines of a mine (broken or fractured ore, stope fill, caved material, ores in permeable zones) or in dumps, prepared ore heaps, slag heaps, and tailing ponds on the surface. These materials represent an enormous, untapped, potential source of all types of metals. The field of chemical mining, now in its infancy, encompasses the preparation of ore for subsequent in-place leaching, the flow of solutions and ionic species through rock masses and within rock pores, the leaching of minerals with inexpensive and regenerable lixiviants under prevailing conditions of the in-place environment, the generation and regeneration of such solutions, and the recovery of metals or metal compounds from the metal-bearing liquors. It is not inconceivable that eventually our ore reserves will consist largely of low-grade, refractory, and inaccessible new deposits and low-grade zones near previously worked deposits, caved and gob-filled stopes, waste dumps, tailing ponds, and slag-heaps. Chemical mining promises economic recovery from these types of deposits. Before it can come of age, however, a much better understanding is needed concerning its chemical and physical aspects.

Jan 1, 1967

By Edward Keller

In order to conduct intelligently the sampling of copper of various forms and grades, solid or in molten furnace-charges, a knowledge of this subject is essential. Yet figures and tests have been persistently withheld from publication, and the books at our command give us little or no information in this regard. This gap in our copper-literature has led to a series of experiments, the results of which are given below. Nearly all gold- and silver-bearing copper, destined for shipment, is cast into the form of bars or pigs. For the sampler, the question arises, Does copper, so cast, remain homogeneous ? If it does, sampling should present no difficulties; but, from experience, we know that this is not the case, and we are thus led to study the behavior of the precious metals arid impurities in copper when the latter changes from the molten to the solid state. For the purpose of the experiments here described, all available grades of copper were selected, and all of them mere subjected to the same conditions, an important requisite for proper comparison. The molten copper obtained directly from reverberatory- and blast-furnaces was cast in a cast-iron mould, the sides and bottom of which were 1 inch thick, and would, therefore, give the copper a fair length of time to chill. The inside dimensions of the mould, and, consequently, of the block of copper obtained, were: length, 10 inches; width, 9 inches; and depth, 5 inches. Fig. 1 illustrates the method employed to obtain samples from these blocks. A was cut away, and the face so produced BALTIMORE COPPER WORKS,

Jan 1, 1898

By Huajun W, Long LZ

The composition of fly ash and formation mechanism of cennospheres are introduced in this paper. The signification of using this potential new mineral processing resource is emphasised. The beneficiation properties of the components of fly ash, such as susceptibility, specific gravity, size, shape and flotability etc have been examined in detail. A technique was designed to process fly ash from the XiGaoJing power plant in Beijing, and a flowsheet is also presented. Flotabld cennospheres, magnetic beads, sinkable beads, carbon and advanced pozzolamics can be obtained as separate products through this flowsheet. It is emphasised that the beneficiation of fly ash is an efficient means of totally utilising the resource. Examination of the products show that they have good physico-chemical properties. Possible areas of their application are also Suggested.

Jan 1, 1993

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015