Search Documents

Discussion of the paper of L. C. MORGANROTH, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2345 to 2352. D. T. DAY, Washington, D. C.-I would like to hear some further detail as to the California deposits. L. C. MORGANROTH, Pittsburgh, Pa.-We have examined the California deposits at various times; I have been over practically all of them myself. These deposits are all of the massive variety. While it is possible that it could be mined and used for metallurgical purposes, it is not feasible because it costs too much. At the present time magnesite which is mined in California is used in the making of plaster, or by the paper trade. Careful figures show that if the California magnesite could be delivered to Atlantic seaports in the crude state at not over $4 a gross ton, and assuming that it would give the same results as the Austro-Hungarian magnesite, it would be cheaper to use the latter. It is also more difficult to dead-burn the massive magnesite, for while it starts to give up its gas readily, the difficulty consists in driving off the last few per cent., and unless this is driven off the magnesite will absorb C02 from the air, so that in a few months it may have 10 or 12 per cent. DAVID T. DAY.-How is the Austro-Hungarian supply at the present time ?

Jan 4, 1915

The Effect of Ionic Strength of Plant Water on Valuable Mineral and Gangue Recovery in a Platinum Bearing Ore from the Merensky Reef

Sep 13, 2010

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

By H. O. Jahns, R. A. Greenkorn, R. E. Haring, L. K. Shallenbarger

This paper is a study of the effects of heterogeneity on flow in an analog of porous media, the Hele-Shaw model. l-3 A set of experiments in heterogeneous Hele-Shaw models showed streamlines through and around heterogeneities of various sizes, shapes and levels. (A level, we define as the ratio between the transmissibility of the heterogeneity and that of the rest of the model.) The heterogeneities were restrictions or expansions of the flow stream analogous to variations in the transmissibility of porous media. The experimental data agreed well with numerical results and with an analytical solution, which we derived for a circular heterogeneity in an infinite field. This study considers the flow-stream distortion due to the shape, size and level of heterogeneities. Size and level are much more important than shape provided the heterogeneity is not long and narrow. Our analytical solution shows that a circular heterogeneity in a large field can be replaced by an equivalent circle of either zero or infinite permeability. The radius of the. equivalent circle is a simple function of size and level of the actual circle. INTRODUCTION With the availability of high-speed computers and numerical procedures to predict reservoir behavior, we are faced with an important question. How much information about the reservoir do we need to justify the cost of the computer in any given case? To answer this question, we have to know how various reservoir parameters affect flow behavior. Reservoir heterogeneity is one of these parameters. In this study, we used a simple, two-dimensional model of porous media, the hele-shaw model, to investigate the effect of heterogeneity on flow behavior. We restricted ourselves to linear, single-phase, steady-state flow in a rectangular field with a single heterogeneity at its center. The analogy between flow in Hele-Shaw models and in porous media is easily verified. Let us first consider a homogeneous Hele-Shaw model with constant plate separation h. (The Hele-Shaw model is constructed by placing two plates, usually glass, very close together and allowing liquid to flow between them. Streamlines are made visible by introducing colored fluid into the space between the plates at a number of points across the model.) We assume a cartesian coordinate system with its origin in the middle between the plates and the z axis directed perpendicular to the glass plates (Fig. 1). The fluid flow is always in a direction parallel to the glass plates and varies from a maximum value to zero in the very small distance from the middle (z = 0) to either plate (z = h/2). For slow motion of an incompressible fluid, neglecting inertia and body forces, we have the viscous flow equation: where p is the fluid pressure, p the viscosity, and v the velocity vector with components u, v and w in the x, y and z directions, respectively. In our rase. and the derivatives of 3 with respect to x and y are small as compared with the derivative in the z direction. Therefore, approximately, with Vp and v being two-dimensional vectors in the x-y plane. Two integrations with respect to z give

Jan 1, 1965

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

By James E. Chapman

The observations here presented are not those of an expert accountant, but of one who, while he has seen considerable service in the accounting departments of large companies, has spent more time in engineering and operating. This paper is intended to cover, in a measure, mine accounting for small mines, as distinguished from the elaborate systems, requiring many persons in the accounting department. I shall attempt to outline a system embracing the essentials of accounting, and simple enough in form to permit one or two persons to carry it on from month to month, in sufficient detail to be able to tell quickly the grade of ore, the prices received for metals, costs per ton for mining and milling, costs per foot for development, upward or downward tendencies in costs, ore settled or in transit, cash on hand, stocks of supplies on hand, efficiency of labor, etc. As in all accounting, there are two main divisions: that of revenue received for what is sold, and that of disbursements made for what is bought, so in mine accounting we have to consider chiefly the income derived from sales of ore or concentrates, and the expenses incurred in producing the said ore or concentrates in a marketable condition. I. Income The revenue of a mining company from the sale of ore or concentrates comes in the form of remittances, accompanied by settlement sheets made out by the buyer of the mine product, such as a smelting company. It is the duty of the mine accountant (or the person to whom this is assigned in connection with other work) to check these settlement sheets, against both the mine weights and assays, and the schedules of prices arranged between the mine and the smelter. As a rule, quotations for silver, lead, zinc, copper and other metals enter into the settlements, and require checking, as do also bills of lading. Each step of the arithmetical calculation is also checked.

Jan 1, 1917

The banquet Wednesday evening was attended by about 700. The list of speakers was unusually brilliant and each one proved to be so interesting that it was nearly midnight before the dancing began. Capt. Robert W. Hunt was toastmaster. Captain Hunt is about to celebrate his eighty-first birthday but is blest with unusual vigor and it was a great pleasure to all his friends to honor him at this time. His selection is toastmaster was a happy one. The guest of the evening, if among so many stars one could be selected from the rest, was Charles M. Schwab, who said nothing but the urgent telegram from his dear old friend, Captain Hunt, could have drawn him away from his seclusion on his Pennsylvania farm to attend the meeting in Chicago. Mr. Schwab's address was, as usual, scintillating with wit and humor; and while lie did not directly or indirectly allude to the steel strike lie did at the end of his talk discuss serious things and gave it as his opinion that any effort to legislate or control the high cost of living would be futile until this country got down to a basis of an honest day's work for an honest day's wage.

Jan 11, 1919

By Robert A. Jankowski, Charles D. Taylor

The objective of this program was to conduct dust surveys at six longwall sections having double-drum shearers, that were regularly in compliance, and to identify the dust control techniques that were the most effective. As each of the mines selected had a record of regular compliance with the Federal Dust Standard, all sampling was "short-term" (often less than 30 minutes) and no attempt was made to relate the survey results to dust-sampling results obtained by the companies for compliance purposes. The sampling procedures (1) used during this survey were developed jointly by the Bureau of Mines and Foster-Miller Associates, Inc. In addition to monitoring dust levels, measurements were also taken throughout the shift to monitor airflow along the face and water usage on the shearer. This program was a cooperative effort of the Bureau of Mines and the Mine Safety and Health Administration (MSHA). The following MSHA health specialists contributed to its successful completion: Paul Lenyo, CMS&H, Dist. 2; Ellis Mitchell, CMS&H, Dist. 3; Carl Jenkins, CMS&H, Dist. 4; David Stritzel, CMS&H, Dist. 8; and John Prelc, CMS&H, Dist. 9. RESULTS CUTTING SEQUENCE - WORK LOCATION At all mines surveyed, an important factor in controlling dust exposure at the shearer is the design of the cutting sequence so as to allow the shearer operator to work most of the time on the intake-air side of the lead drum. It is generally accepted that most of the dust generated by a double-drum shearer comes from the lead drum, which in the raised position normally takes a full sump. Because the position of the drum that is in the raised position determines the horizon control, the operator must be close enough to carefully monitor its operation. Therefore, his position relative to the lead drum has a significant effect on his dust exposure. Dust profiles, such as those constructed from data collected at Mines A and B (Figure 1), show the large gradient in dust concentrations that can exist between the intake and return air side of the lead drum. When the primary cut is taken head to tail, the lead drum is downwind and dust levels can be maintained at a low level until air has passed the shearer (Mine A). Thus, shearer operators can stay in relatively uncontaminated air. When the primary cut is taken tail to head, the lead drum is upwind of the shearer controls, resulting in higher dust concentrations at the shearer operator's work location (Mine B). At the mines where this cutting sequence was used, it was company policy for the shearer operators to walk on the intake side of the lead drum, returning to the controls only to adjust the height of the lead drum. DIRECTED WATER SPRAYS AND PASSIVE BARRIERS It is not always possible to keep the shearer operator on the intake air side of the lead drum. Various techniques have been tried to keep the dust generated by the shearer away from the machine operators when they work adjacent to the shearer. At all mines visited, the external water spray nozzles were directed so that dust from the shearer was directed downwind and toward the face, and away from the shearer operators. The effectiveness of using external water sprays to keep dusty air close to the face was noted during Bureau of Mines efforts to develop improved water spray systems (2). Laboratory and underground tests showed that water sprays located properly and directed downwind can create aiflow patterns that move dust generated by the shearer toward the face and away from the shearer operators. Sprays directed upwind, into the airflow, can actually move dust away from the face

Jan 1, 1982

By F. J. Darnell

SINGLE crystals of a-titanium are difficult to obtain because of the phase transformation at 882 °C in which the structure changes from the high-temperature body-centered structure ß to the low-temperature hexagonal close-packed structure a. Preparation of single crystals of a-titanium has previously been accomplished by a strain-anneal method which takes several days and is not generally reproducible. Single crystals as large as 5 mm

Jan 1, 1959

By Pollyana de Aragão Trigueiro

A distribuição de soluto durante a solidificação rápida de uma liga Ag-15%massaCu, foi obtida numericamente. No presente trabalho, utilizamos um modelo de difusão de entalpia e concentração médias, proposto anteriormente, para a solidificação de uma gota de liga binária (atomização). Nossos resultados mostram que a refusão da estrutura pode gerar um perfil de microssegregação em ligas solidificadas rapidamente bastante diferente dos que resultam da solidificação perto do equilíbrio.

Aug 7, 2018

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By H. D. Hoskold

DuRing the last few years, various persons have been put forward as originators of some mechanical device for the purpose of finding distances without the use of a chain or other linear measuring-instrument, and among these, the Englishman, Gascoigne, 1639, is prominent as the first in England; while James Watt, 1771, and William Green, 1778, are also included in the list of inventors. It is possible that this useful and important problem occupied the attention of others prior to the date cited, and, consequently, it is difficult to decide what nation first gave birth to the inventor of an instrument for the object under consideration. A very important work appeared, not long since, in Paris, devoted to a history and discussion of some of the older and newest forms of surveying-instruments,* and at page 79 of that work a curious old instrument is exhibited, called Bigonometre, i. e., an instrument for finding distances and solving trigonometrical problems. in surveying. A copy of the diagram of the instrument exhibited in the book referred to is represented in Fig. 1. Having had an occasion to read the French work referred to, I communicated with the author of it, and he was good enough to reply that he found a diagram of this old instrument in a book published in 1597, by Danfrie, existing in the library of the Academy of Sciences, in Paris. Col. Laus-

Jan 1, 1904

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

The Institute is one of the five national societies that joined in organizing the Congress, the others being the American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers, and the Society of Naval Architects and Marine Engineers. Each society has pledged from its general funds or some special fund a certain sum to guarantee the success of the Congress. To this the engineers resident on the Pacific Coast added $13,000, the total guarantee fund amounting to $37,000. It is hoped that this money, iii part or in whole, can be repaid to the guarantors of the Congress. The sums necessary to conduct the latter and to publish the proceedings, are to be derived from membership fees paid equally by all participating. A member of the Institute as such is not a member of the Congress and will not receive any of the publications of the latter. He is eligible to become a member of the Congress and it is hoped that he will do so. The membership fee is $5, and this entitles one to receive the introductory volume of the Congress containing the proceedings; a digest of the other volumes and a general index. It also entitles the member to one other volume of the transactions, to be chosen as he will. For moderate sums he can buy additional volumes, the whole set costing delivered, $30 or less. On Jan. 12 the total membership was 2,350, of which only 290 were recorded as mining engineers. Full details regarding the Congress have been sent to every member of the Institute, and the failure of the members to take a more active interest in the matter is believed to be due to some misunderstanding of the situation.

Jan 4, 1915

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938

By J. T. Hayward

Studies of the forces and conditions governing the recovery of petroleum from natural reservoirs indicate that a low gas-oil ratio increases ultimate recovery, retards the encroachment of water and tends to reduce lifting costs. Methods for controlling and reducing gas-oil ratios in producing wells consequently have been given considerable attention during the past few years. However, during this same period, the production from wells in nearly all fields has been fixed by proration agreements and it is the opinion of the writer that where a well is required to produce steadily at a predetermined rate, less than its "potential" or maximum capacity, the gas-oil ratio will depend only upon the rate of production, and will be independent of the method of production and of the design of equipment in the well. If no change in the rate of production is contemplated, efforts directed to improving the gas-oil ratio by altering the diameter of the flow string, changing the position of the choke, assisting the flow with gas-lift or pump, etc., will be unsuccessful. This viewpoint is not new. It was presented by H. N. Marsh and B. H. Robinson in 1929,' but it has not been generally accepted. Although engineers believe that the rate of withdrawal and not the equip ment used governs the water-oil ratio, a similar opinion regarding the gas-oil ratio is not so commonly admitted. The rates of flow of oil and gas into the base of an oil well depend upon the following conditions: 1. The characterist-ics of the oil and gas. 2. The characteristics of the underground reservoir. 3. Temperature and pressure conditions in the reservoir. 4. The back-pressure held against the face of the sand. In operating a well, the only one of these conditions over which control may be exercised through operating procedure and the use of equipment above the sand is the back-pressure at the face of the sand. Strictly speaking, the back-pressure varies over the face of the sand, owing

Jan 1, 1932

Regional problems, such as political risk and debt reschedulings, in Pacific Rim nations coupled with the price volatility of gold mean that multi-faceted financing packages are needed to offset the many risks inherent in a new gold mine development. The cross-border risks of getting money back out of a producing mine may require the involvement of export credit agencies, multilateral government banks, or political risk insurance. Variations on forward gold sales, gold loans, or offset structures can also enhance the flexibility and safety for the providers of both the debt and equity. The region will become as large a gold producer as South Africa by 1990. The large dollar amounts for both investment and revenues realised are of great significance to the economies of many of the Pacific Rim countries especially as a means to increase foreign exchange earnings.

Jan 1, 1987

By Bennett Bates

NOWHERE in the world has cone classification in closed-circuit grinding with tube mills reached as high a state of development as on the Witwatersrand. In the development of the Far East section the necessity of fine grinding to obtain. satisfactory residues gave rise to a situation with which the cone could cope only at a great sacrifice in efficiency of tube-mill grinding. H., A. White1 recognized the limitation of the cone in his study of the theory of tube milling as early as 1915, but it was not until Ewing, Davis and. Willey2 carried out their tests at Springs Mines during 1920 that the advantages of mechanical classifiers' were demonstrated. During the fall of 1924 the writer supervised a series of tests with Dorr classifiers undertaken by Mr. White, Consulting Metallurgist, at the mill of the Geduld Proprietary Mines, Ltd., Dersley, Transvaal (Far East Rand). The importance of classification to obtain efficient tube-mill grinding was thoroughly demonstrated. The installation of classifiers of the above type that followed the test, confirmed the results of the experimental work.

Jan 2, 1926

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929