Search Documents

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

The Institute is one of the five national societies that joined in organizing the Congress, the others being the American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers, and the Society of Naval Architects and Marine Engineers. Each society has pledged from its general funds or some special fund a certain sum to guarantee the success of the Congress. To this the engineers resident on the Pacific Coast added $13,000, the total guarantee fund amounting to $37,000. It is hoped that this money, iii part or in whole, can be repaid to the guarantors of the Congress. The sums necessary to conduct the latter and to publish the proceedings, are to be derived from membership fees paid equally by all participating. A member of the Institute as such is not a member of the Congress and will not receive any of the publications of the latter. He is eligible to become a member of the Congress and it is hoped that he will do so. The membership fee is $5, and this entitles one to receive the introductory volume of the Congress containing the proceedings; a digest of the other volumes and a general index. It also entitles the member to one other volume of the transactions, to be chosen as he will. For moderate sums he can buy additional volumes, the whole set costing delivered, $30 or less. On Jan. 12 the total membership was 2,350, of which only 290 were recorded as mining engineers. Full details regarding the Congress have been sent to every member of the Institute, and the failure of the members to take a more active interest in the matter is believed to be due to some misunderstanding of the situation.

Jan 4, 1915

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938

By J. T. Hayward

Studies of the forces and conditions governing the recovery of petroleum from natural reservoirs indicate that a low gas-oil ratio increases ultimate recovery, retards the encroachment of water and tends to reduce lifting costs. Methods for controlling and reducing gas-oil ratios in producing wells consequently have been given considerable attention during the past few years. However, during this same period, the production from wells in nearly all fields has been fixed by proration agreements and it is the opinion of the writer that where a well is required to produce steadily at a predetermined rate, less than its "potential" or maximum capacity, the gas-oil ratio will depend only upon the rate of production, and will be independent of the method of production and of the design of equipment in the well. If no change in the rate of production is contemplated, efforts directed to improving the gas-oil ratio by altering the diameter of the flow string, changing the position of the choke, assisting the flow with gas-lift or pump, etc., will be unsuccessful. This viewpoint is not new. It was presented by H. N. Marsh and B. H. Robinson in 1929,' but it has not been generally accepted. Although engineers believe that the rate of withdrawal and not the equip ment used governs the water-oil ratio, a similar opinion regarding the gas-oil ratio is not so commonly admitted. The rates of flow of oil and gas into the base of an oil well depend upon the following conditions: 1. The characterist-ics of the oil and gas. 2. The characteristics of the underground reservoir. 3. Temperature and pressure conditions in the reservoir. 4. The back-pressure held against the face of the sand. In operating a well, the only one of these conditions over which control may be exercised through operating procedure and the use of equipment above the sand is the back-pressure at the face of the sand. Strictly speaking, the back-pressure varies over the face of the sand, owing

Jan 1, 1932

Regional problems, such as political risk and debt reschedulings, in Pacific Rim nations coupled with the price volatility of gold mean that multi-faceted financing packages are needed to offset the many risks inherent in a new gold mine development. The cross-border risks of getting money back out of a producing mine may require the involvement of export credit agencies, multilateral government banks, or political risk insurance. Variations on forward gold sales, gold loans, or offset structures can also enhance the flexibility and safety for the providers of both the debt and equity. The region will become as large a gold producer as South Africa by 1990. The large dollar amounts for both investment and revenues realised are of great significance to the economies of many of the Pacific Rim countries especially as a means to increase foreign exchange earnings.

Jan 1, 1987

By Bennett Bates

NOWHERE in the world has cone classification in closed-circuit grinding with tube mills reached as high a state of development as on the Witwatersrand. In the development of the Far East section the necessity of fine grinding to obtain. satisfactory residues gave rise to a situation with which the cone could cope only at a great sacrifice in efficiency of tube-mill grinding. H., A. White1 recognized the limitation of the cone in his study of the theory of tube milling as early as 1915, but it was not until Ewing, Davis and. Willey2 carried out their tests at Springs Mines during 1920 that the advantages of mechanical classifiers' were demonstrated. During the fall of 1924 the writer supervised a series of tests with Dorr classifiers undertaken by Mr. White, Consulting Metallurgist, at the mill of the Geduld Proprietary Mines, Ltd., Dersley, Transvaal (Far East Rand). The importance of classification to obtain efficient tube-mill grinding was thoroughly demonstrated. The installation of classifiers of the above type that followed the test, confirmed the results of the experimental work.

Jan 2, 1926

By N. A. Zeigler

The present publication is a continuation of the work on gas analysis described in a paper presented before the Institute of Metals Division year ago.' While that paper was largely descriptive in character dealing with the various parts of the apparatus and method of operations the present one gives numerical data obtained as a result of a series c experiments with iron-carbon alloys. The apparatus and the method applied are essentially the same as previously described, changes bein only in minor details. Attention should be called to the fact that in the present work we ar dealing with the gaseous mixtures obtained as a result of vacuum meltin of various ferrous alloys. It should be understood that when the term "degasified sample" and "products of degasification" are used, the refer to the sample remaining after the vacuum fusion of the alloy an the gaseous products removed therefrom, respectively. The write does not wish to create the impression that the metallic products of thj process are absolutely free from any gaseous elements, nor that the gase obtained are present as such in the original sample. These two point are not yet definitely known and are subjects for future investigatior The point, however, which has been established beyond doubt, i that all the gases dealt with come from the metallic charge and ar present either in the charge as such, or are produced as a result of chemic: reactions going on within the charge. The suggestion that the gases an due to the reactions between the metallic charge and the refractor materials has no valid basis. General Procedure A series of iron-carbon alloys was prepared in a magnesia-line graphite crucible placed in a high frequency laboratory furnace open t the atmosphere. The materials used were Westinghouse electrolyti iron and Acheson graphite. Each alloy, after it was completely molter was kept in the liquid state for 10 min., cast into a small iron mold, an

Jan 1, 1929

By Donald E. Archibald, Gerald A. Allcott

"Noranda's Heath Steele Mine is located 35 miles north of Newcastle in northern New Brunswick. Blasthole open stoping with partial delayed filling is the major mining method in use. The selection of stope and pillar dimensions to ensure mine stability was originally subjective. This paper describes the progress made in attempting to rationalize design.One major feature is the fracture pattern. The main orebody now being mined, the B zone, has undergone five periods of folding and each period of folding developed a family of fracture planes which are axial planar to that particular fold pattern.The other major features considered are the calculated increase in stress due to mining and depth and its relationship to measured strain. Experience has shown that ground problems affecting production have usually originated in rib pillars. Field observations of ground deterioration and multi-wire extensometer measurements of strain are tabulated together chronologically for each pillar.A factor representing stress and a common plane of weakness are identified. Graphical analysis is used to determine the effect of the plane of weakness on a typical stress/strain curve and provides a base for the design of pillars."

Jan 1, 1981

There are many different challenges when sampling mineral commodities. Sampling is part of many decision-making processes, from control of the number of drops of a reagent to all aspects involved in determining how much to pay for a mineral consignment. However, if all decisions must be supported by correct assumptions, or at least agreed terms, how can this be guaranteed? The main approach is to emphasise the importance of continuous surveying of sampling practices. If they are based on non-recommended protocols, this raises concerns. In addition, safety failures and lack of appropriate behaviour from the technical perspective can lead to disasters, both from the human and business perspectives. Impacts on safety and health are clearly unacceptable. It should be noted that imperfect safety and health practices in sampling operations have a strange correlation with incorrect sampling techniques. The commercial interface can also be affected. Companies have studied extensively the various aspects of measuring quality parameters for mineral commodities to understand the risks for investors and owners, and they take decisions that fundamentally respect the interests of parties in contracts and not result in losses. Every result should be obtained in defensible ways, and neither losses nor profits taken in indefensible ways. Most of such situations are related to bias; a significant systematic difference between a measured value and a reference value for a contractual quality parameter. Bias is always undesirable, because it always implies an incorrect advantage for one party and without doubt an undesired disadvantage for the other party. These situations are solved financially through a third-party arbitrator becoming involved in delicate situations, such as a commercial claim, but the outcome is always tangibly or intangibly bad for one of the parties. Another possibility is a permanent or temporary loss of precision. Poor precision, due its nature, generates reasonably balanced losses and profits, but it may hide out-of-control situations, generate instability and induce financial losses due to actions taken towards clearing commercial disputes involving interlaboratory programs, sample exchanges and duplicated sampling and sample preparation procedures, in the end wasting time and resources and creating a permanent source of commercial tension. While bias situations demand immediate adjustments for correctness, poor precision has to be understood as something that cannot be just calibrated out and is a situation that demands investment of time and effort. Precision optimisation has to take into account best practice for obtaining the required precision as well as cost/benefit analysis studies. Purchasers, engineers, salesmen and all personnel need to recognise that sampling is a major area to understand when taking decisions. The aim is to spread concepts that can really help, such as simple in-house actions to improve productivity and completion of surveys on commercial sampling operations, in order to ensure correct results are obtained and assertively take corrective actions, thereby establishing a healthy relationship with investors, suppliers and purchasers and in the process optimising the business.

Jan 1, 2008

By Mirian Mamani

El presente texto describe una base de datos geológica que comprende: geología integrada, estructuras definidas en campo de mediciones y edades en actividad, ocurrencia de minerales metálicos, mediciones de aeromagnetometría y geocronología de rocas ígneas y metamórficas donde es importante delimitar los dominios geotectónicos para la exploración de yacimientos. En ese sentido, el presente texto describe las nuevas zonas propicias para la exploración en el sur del Perú a través de la identificación de fallas corticales y dominios geotécnicos dentro del proyecto GR1: Geología de la Costa Sur y vertiente oeste de la Cordillera Occidental de la Dirección de Geología Regional del Ingemmet.

Feb 1, 2012

By Y. S. Bonillas

IRA B. JORALEMON, Warren, Ariz.-This paper has covered the situation so well that I have few suggestions to offer. Two points, however, are shown more clearly in the lower mines of the Calumet Arizona Mining Co. than in Copper Queen workings, and may be worth mentioning. The first is the usual association of high-grade primary sulphide orebodies with much larger masses of pyrite and silica, averaging less than 1 per cent. copper. The richer areas occur sometimes around the borders of the lean pyrite bodies, and sometimes entirely within them. While as yet we have not been able to find any certain reason for the location of high-grade sulphides in low-grade masses, it seems likely that the age of fracturing is one controlling feature. The first stage of mineralization, with pyrite and silica, had the effect of sealing up the rock. The later solutions, richer in copper, could pene-

Jan 12, 1916

A HIGHLY successful joint conference on coal-mine transportation was held at Pittsburgh on Oct. 20 by the Pittsburgh Section of the American Insti-tute of Mining and Metallurgical Engineers and Mining Section of the Engineers' Society of Western Pennsyl-vania. C. E. Lesher, executive vice-president of the Pittsburgh Coal Co., presided over 215 members and others in the morning and Graham Bright, sales en-gineer with the Mine Safety Appliances Co., presided over about 180 in the afternoon. There were four prepared papers and much discussion, as well as a good luncheon between the sessions. Mechanical loading in the Pittsburgh district was discussed by L. E. Young, production vice-president of the Pittsburgh Coal Co. More companies in this district are using loading machines, more types of machines are being tried, and more coal is being mined by them than heretofore. The draw-slate above the Pittsburgh seam is the main problem; but devices for supporting and moving draw-slate are being tested. Except in two mines, the slate is being taken down. The fundamentals of the machines are similar, but the electrical drive and other parts have been improved. The problem is to recover or move as much coal as possible without hand labor. Methods of cleaning coal must be improved to meet the new methods of loading. The Pittsburgh Coal Co. has ten Joy machines and others are under order, a Myers-Whaley machine, Jeffrey conveyors, and Eichoff conveyors. The last mentioned are used in entries and other conveyors in rooms. At Montour No. 10 mine, one Joy machine is worked in rooms and one in entries.

Jan 12, 1927

By Spencer R. Titley

"For his pioneering contributions to the understanding of the geology of porphyry copper systems" Recipient Of The 1997 D. C. Jackling Award SPENCER R. TITLEY Introduction The subject of this lecture, a late century perspective on porphyry copper geology, is one of current interest and importance as the search for these ores remains intense. It is presented in the belief that an appreciation of our present understanding of the subject requires it to be viewed historically, thus providing a basis for evaluating appropriate directions for continued study. At the outset, it is important to note that the technology of mining and extractive metallurgy has developed ore from these low grade orebodies, starting with D. C. Jackling, and has continued to create them as copper grade and price have diminished. But the continued search for them is a geological problem that responds to growing expectations of people and societies; exploration based upon ever increasing knowledge of the habits of the ores has been very successful. This is the story of evolution of geological thought and practice in porphyry ore search across an interval of time beginning with the bulk mining of "low grade" copper ores at Bingham and ending with late Century concepts. "How did we get here?" The lecture concerns the ideas of many different people. The ideas and events discussed reflect a bias on North American thought, where the great low grade orebodies were first recognized as such and where many of the basic geological ideas were developed. A very great number of geologists have contributed to this understanding. In no sense is it meant to minimize the contributions to the story that have evolved in the study and mining of ores of the Andes, whose development and expansion has been nearly synchronous with that in North America - nor to minimized comparable contributions made in the late century from studies of the newer discoveries of deposits in other regions, especially the southwestern Pacific regions. In expansion of this topic, I have found that many important concepts are marked by appropriate publication but some are not, or I have not been able to discover documentation. Many notions appear to have become conventional knowledge without publication, mostly being geological viewpoints developed synchronously from similar observation. Thus, apologies are extended in advance to those whose work I have might have missed and to those unknown to me whose unpublished ideas may have seeped into the pool of common knowledge without appropriate recognition. The analysis here addresses events of two time segments, an older one extending from the developments at Bingham in the early 1900s through the Second World War, ending about 1950: the second period extends from that time to the present. This separation is seen in Figure 1, which traces numbers of publications through the period as extracted from some 700 publications, again with a North American bias, from an annotated bibliography of porphyry copper geology in preparation. During the early period, exploration was "immature" in North America, that is, geologists looked for new districts and sites of the deposits. Outcrops were sought that carried the signatures of former mineralization and regional controls related to structural geology were closely studied. In the later period, North American exploration had "matured" into a study of districts, rather than a search for them. As the studies of these ores intensified during the younger period concommitant with increasing demands for the metal, they did so with a broadened understanding of some habits of occurrence, of hydrothermal alteration, mineral zoning, petrology, and geochemical and geophysical signatures. Outside of North America, search remained "immature" but closely related to the

Jan 1, 1998

By Herbert S. Richey

Two hundred years ago next April, our forebears embarked upon the difficult path to national independence. They succeeded, and shook off the yoke of foreign domination. In the ensuing two centuries, the country was mobilized several times to protect that political and economic independence from foreign domination. These efforts were also successful. Thus, as we stand here on the threshold of our third century of political independence, we can thank previous generations and congratulate ourselves for establishing and maintaining the world's oldest republic. Now -- once again -- the United States faces the challenge of foreign intervention into our economy. This time the battleground is resource avail- ability. America has been blessed with enormous resources. Whether we speak of minerals or timber or water or "amber waves of grain," this nation has benefitted from a resource base that is the envy of the world. This asset, coupled with a political system that permitted us to develop it, has been the physical backbone of our independence. Without the economic independence that this resource base has given us, the political independence we fought for would have been tenuous, at best.

Jan 1, 1975

By William I. Gardner

Optimum design of a structure obviously requires a thorough knowledge of the materials to be utilized in its construction. When the structure is a tunnel, a most important element in its design and construction is the geology. As a tunnel may be many miles in length and at depths of hundreds or thousands of feet, we face a real problem to meet the needs of the designer and builder. How can we determine the properties of our construction materials in this situation? Engineering geology has had a formidable challenge to meet the requirements of conventional excavation methods; the advent of machine methods for rapid excavation compounds the requirements for more detailed and more precise geological knowledge of the tunnel site. This chapter will discuss the means now at our disposal to meet the challenge to produce the required data on the tunnel site in the preconstruction stage. Our considerations will be directed towards construction of a free-flow tunnel, primarily in fractured rock formations, without any requirements for the rock mechanics type of in-situ tests that might be made for a pressure tunnel or for a large opening for an underground power plant. In essence the investigation must determine: (1) The geologic conditions affecting the type of construction equipment and excavation method of the rock to be broken and removed. (2) The quantities of water and gas to be encountered. (3) The strength and stability of the material surrounding the bore and its need for support and lining. GEOLOGICAL FACTORS AFFECTING TUNNEL DESIGN AND CONSTRUCTION The engineer or contractor may classify the rock as either competent or incompetent or more pointedly as "good" or "bad" ground. The geologist may bestow a precise petrographic name upon the rock, such as granodiorite or indurated tuff breccia or name the formation, as Mancos shale, for

Jan 1, 1970

By E. DeGolyer

THE petroleum production of the world for 1924 again passed the billion-barrel mark, as it did in 1923. A preliminary estimate of production is 1,016,000,000 bbl., a decrease of 1,100,000 bbl., or less than 1 per cent. from the 1,017,100,000 bbl. produced in 1923, the year of greatest production. FIG. 1.-TOTAL WORLD AND UNITED STATES PRODUCTION. Production in the United States decreased 18,500,000 bbl., the. first decrease in yearly production since 1906. Mexican production decreased almost 10,000,000 bbl. Russia, Persia, Roumania, Venezuela, and Peru increased their production by an amount almost great enough to offset the decline in the United States and Mexico. The decline in the production in the United States and Mexico was considerably less than anticipated by leading geologists, economists, and statisticians; nor did the increase in consumption entirely meet the expectations of estimators. Early in the year, the statistical department of one of the most important oil companies forecast a draft on stocks, from an excess of demand over supply, of about 80,000,000 bbl. Instead of decreasing our stocks, they were increased by about 33,000,000 barrels.

Jan 3, 1925

Jan 1, 1969

YEARS ago, when metal mining was more an adventure than a well-organized business, it was often said (with some color of truth) that unless a mine could stand bad management or mismanagement, it was not much good. Today, the natural excellencies of an ore deposit are merely a challenge to the engineers to exploit it as skillfully, as efficiently, and as profit- ably as possible. A vast amount of competent and imaginative engineering management (which includes economic analysis no less than the technologic arts of mining ore and treating it) has been required to make New Cornelia the smooth-running and successful operation that can be seen at Ajo today. New Cornelia was acquired by the Phelps Dodge Corporation when it absorbed the Calumet and Arizona Mining Company in 1931. Next to Morenci, it doubtless is the corporation's biggest asset. It in no way detracts from the achievement of Phelps Dodge engineers to say that they had an admirable ore deposit to work on. New Cornelia ore, as mined, is relatively low in grade and the deposit is by no means the largest of the Porphyries; but it has these attractive features : (1) It is peculiarly suitable for opencut mining because: (a) The overburden of waste rock lying above the ore deposit was (it has long since disappeared) almost negligible. (b) The deposit is roughly circular in horizontal section, with the horizontal dimensions four to five times as great as the maximum thickness. (Nevertheless, eventually some underground mining may be desirable.)

Jan 1, 1957

By G. K. Manning, A. R. Elsea, C. R. Simcoe

It was found that a critical boron content exists which yields the maximum boron-hardenability effect in hypoeutectoid steels, as was predicted from the mechanism proposed in a previous paper. The hardenability of boron steels with boron contents between 0.00005 and 0.0017 pct was dependent on the boron content, austenitizing temperature, quenching temperature, and austenite grain size. The effects of these variables on hardenability can be explained by the mechanism previously proposed for the boron effect. A MECHANISM has been proposed to explain the effect of boron on the hardenability of steel.' The proposed mechanism assumes that transformation particles nucleate at concentrations of lattice imperfections where the energy level is high, and

Jan 1, 1957

By P. Rosten

US mine production of iron ore in 1984 showed some improvements compared to 1983. But reduced demand from the iron and steel industry caused temporary shutdowns of many iron ore mines and pelletizing plants. US raw steel production in 1984 was slightly above 1983, but still at a depressed level. Production was 83 Mt (92 million st), compared with 77 Mt (85 million st) in 1983 and 68 Mt (75 million st) in 1982. Two major production trends continued in 1984. They were the increased production from electric furnaces and the growing use of continuous casters. Electric furnace production included 33.2% of the steel poured in 1984, compared with 31.5% in 1983. Continuous casting was used for 39% of 1984 steel production, compared with 32.1% in 1983. Statistical Process Control Statistical Process Control (SPC) has taken on new proportions in the iron ore and steelmaking industries within the last year. This mathematical technique is used to monitor, control, evaluate, and analyze a manufacturing process. The technique charts variability of important quality parameters. Training and adaptation of SPC techniaues for process control have been initiated at Inland, Steel's Minorca, Pickands-Mather's Hibtac, Cleveland-Cliff's Empire and Sherman operations, and at Reserve Mining. One of these operations has requested its bentonite supplier provide SPC charts on quality specifications. Some of the steelmaking operations (Inland Steel, Bethlehem Steel, Dofasco, LTV Steel, National Steel, Stelco, Weirton Steel, and Wheeling-Pittsburgh) have set up SPC programs within their operations. And they also have insisted that some of their suppliers use SPC. Plant Shutdowns The permanent closure of Stelco's Griffith mine at Red Lake, Ontario, has been delayed by one year. This gives employees more time to adjust. The mine is now set to close in April 1986, instead of April 1985. Sidbec (Canadian government) and its other partners (including British Steel Corp., Quebec Cartier Mining, and US Steel) closed its iron mining operations at Gagnon, Quebec. The pellet plant has been leased to Quebec Cartier. New Iron Ore Operations The massive Carajas iron ore project in Brazil is scheduled to come onstream in Jan. 1986. It is to achieve full-scale commercial shipments by July of that year. The 66% iron crude ore requires only crushing and screening before shipment. The product consists of 83% sinter feed and 17% coarse ore. Annual production capacity will be 32 Mt (35 million st) when the project is completed. Principal customer for the ore is Nippon Carajas Iron Ore Co., a consortium of Japanese steel mills. The Arab Iron & Steel Co. (AISCO) has started up a $US300 million, 3.6 Mt/a (4 million stpy) iron ore pelletizing plant built by Kobe Steel Ltd., at Al Hidd-hide in Bahrain. By 1986, this grate-kiln-cooler plant will supply high quality iron ore pellets to feed direct reduction plants in the immediate Gulf area and Far East markets. Iron ore supplied from Brazil, Peru, India, and Mauritania provides the feed to the pellet plant. Hydrated lime (2%) is used as a burden.

Jan 5, 1985