Search Documents

By Stuart E. Buckley

The application of hydrocarbon equilibrium data to various problems encountered in refining and in natural gasoline recovery is an old and well established practice. Both generalized data and data on specific hydrocarbon systems have been made available by a number of investigators. More recently such data have been applied to the relations governing the separation of oil and gas both in the reservoir and at the surface. Most of the applications to production problems, however, have been based upon examinations of surface samples of oil and gas. This paper describes a technique that has been used satisfactorily in a number of cases to calculate directly from the hydrocarbon analysis of and auxiliary laboratory data on a subsurface sample of the reservoir fluid the behavior of the oil and gas during the various stages of separation at the surface incident to production. Types of Information Calculated The system of calculations is not designed to supplant field data, but rather to correlate with them laboratory data obtained under controlled conditions in order to obtain a more complete and exact picture than usually is possible through the use of field data alone. The chief advantage of the calculations is the possibility of their use at a minimum of both time and expense to determine completely the effect of any possible operating technique upon each of the following: (1) The gas-oil ratio resulting from liberation of the dissolved gas; (2) the composition and gasoline content of the liberated gas; (3) the composition and gravity of the residual oil; (4) the amount and composition of the gas liberated upon flashing the oil from the separator to the stock tank; (5) the shrinkage of the oil in passing from the reservoir to the stock tank. This information is frequently essential to the correct determination of the advisability of installing a natural gasoline plant, to design such a plant to take care of seasonal production, and to determine the optimum separator pressures to carry in various parts of a field.

Jan 1, 1938

By Read T. A

THE Broken Hill South Ltd. is one of ten companies operating on the Broken Hill lode (See Fig. 1). It has two leases-Blocks 7 and 8-of a total length of 2250 ft. on strike of lode.From the surface to 425-ft. level the ore was found principally in the form of carbonates and high-grade friable sulphides. Below the 425-ft. level the ore is found in the form of compact sulphides. The ore-bodies found in the South mine may be broadly divided into two classes...

Jan 1, 1921

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By K P. Tully

In August 1996 a Microseismic Monitoring System developed by ISS International Limited was installed at the Pasminco Broken Hill Mine -Southern Cross area. The project aims were to:Assist in daily safety management in a mine environment which exhibits one of the highest occurrences of microseismic activity recorded in the Australian mining industry. Be used as a proactive tool in design of future development and stoping. The project to-date has been an unqualified success in achieving both goals. Consequently the system is being expanded from 6 to 14 monitoring sites.

Jan 1, 1998

By M. Botz

For leach solutions containing primarily free cyanide, the silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method significantly over-estimates the concentration of free cyanide and under-estimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric titration method for determining WAD cyanide that overcomes issues with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to fully release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, accurate WAD cyanide measurements were achieved using the MP-WAD method. Analyses obtained with the new method were found to be within about ±10% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.

Feb 27, 2013

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

PRESIDENT BENJAMIN B. THAYER,2 NEW YORK, N. Y. PAST PRESIDENTS JAMES F. KEMP,1 NEW YORK, N. Y. CHARLES F. RAND,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 .NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY. BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 7, 1914

By Ikuya Takase

INTRODUCTION Since the occurrence of the first oil crisis, coun-tries of the world, especially oil-importing countries have made sustained and vigorous efforts to lessen the dependency on oil as a source of energy supply. The adoption of "Principles of Coal Policy" by the IEA Ministerial Governing Board Meeting in May, 1979 was the first formal action taken by major energy consuming countries. At the Venice Summit in June, 1980, it was agreed that production and use of coal should be doubled over the next ten years. In fact, the world coal use in 1980 showed around a 10 percent increase over the previous year. Recently, we have seen an indication that the balance of oil supply and demand in the short term have eased. But I believe that it remains vital that we continue to encourage the development and introduction of alternative energy sources. Because, from the medium and long range viewpoint the recovery of the worldwide economy will lead us to increased oil requirements and thus we will be faced with the cyclical, structural tightening situation between the supply and demand of oil. Moreover, we are still convinced that the constraint of the supply capabilities of the Middle-East nations may be increasing in the long-term, since there still remains political uncertainties among these nations. Consequently, above all, coal is viewed as an alternative energy resource available for immediate expansion of use and is given as high a priority as nuclear power. In Japan, we regard coal as the most reliable alternative energy resource to replace oil. According to the "Alternative Energy Supply Targets" approved by the Cabinet in November, 1980, the level of coal imports is estimated to approximately double by 1990, while our domestic coal production will remain nearly at the same level. The transition from oil to coal is found in the recent import levels of coal---73 mil¬lion tons in 1980, a 23 percent increase over the 59 million tons imported in 1979. There was an upsurge in steaming coal imports, reflecting the transition in feedstocks---7.2 million tons in 1980, four times over the previous year's amount. Henceforth, from the medium to long range view, the demand for coal, especially that of steaming coal is forecast to continue to grow. The timely expansion of supply capabilities is our utmost concern and should be one of the most significant goals of our comprehensive policy. The Overseas Coal Investigative Committee, a privately organized advisory panel to the Director-General of the Natural Resources and Energy Agency of the Ministry of International Trade and Industry (MITI), investigated means to secure a stable supply of overseas coal. The panel presented its interim proposals in August, 1981, recommending the diversification of coal import sources, extensive use of low rank coal, as well as enhanced international cooperation between coal producing and importing countries. THE CONTENTS OF THE COMMITTEE'S REPORT Four Points for Major Consideration In order to ensure a stable supply of overseas coal, Japan needs adequate policy measures consistent with the characteristics of coal resources and environmental requirements, giving consideration to Japan's status and the role she is expected to play in the areas. From the above, great importance should be attached to the following four points: All the components of the "Coal Chain" (Namely, the development of mine sites, construction of railroads, port loading facilities, coal shipping vessels, port receiving facilities, including coal centers and international transport facilities etc.) should be reviewed and reformed with steps taken to assure efficiency consistent with the entire coal chain system. The complete formation of a coal chain system requires such lengthy lead times and huge amounts of investment that necessary measures should be undertaken well in advance utilizing long-range projections of future demands and various economic surveys. Policy planning should be conducted taking into account of harmonizing stability and economics of the supply structure. For ensuring the long-term stability and expansion of the coal trade, international cooperation on a bilateral and multi-national basis should be encouraged. Mutual understanding and close relationships are essential to facilitate the formation of the supply system and to promote the extensive use of coal. Direction and Problems Related to Supply Stability Expansion of Supply Capabilities. World coal imports in 1979 amounted to 229 million tons, of which Japan's share amounted to 59 million tons, or one fourth of the entire amount. The imports of European and Asian countries accounted for 83 million tons and 7 million tons respectively. According to the examination of the Investigative Committee, Japan's coal requirement is estimated to be between 140-150 million tons by 1990, nearly the same level as announced in the Provisional Long-Term Energy Supply and Demand Outlook in 1979. This fore¬cast is-to be revised in April, 1982. Japan's demand is expected to be met through fiscal 1985; however, by 1990, the supply is estimated to fall short of demand, particulary, in the field of steaming coal. For the expansion of supply capability, first, mine development should be accelerated. The proposed

Jan 1, 1982

By Albert E. Wiggin, Frederick Laist

Page I. Introduction............................470 II. The Sources and Amount of Slime................470 II. The Composition of the Slime..................471 IV. The Experimental Development of the .Anaconda Slime Plant.. 471 1. The Great Falls Slime Plant and Experimental Work......471 2. The Experimental Work Done at Anaconda..........473 (a) SlimeThickening Devices.............. 474 (b) SlimeConcentrators................. 475 (c) Dewatering the Slime Plant Concentrate......... (d) The Use of Chemicals to Accelerate the Settlement of Slime........................ 478 (e) The Effect of Temperature upon the Settlement of Slime 478 V. A Description of the Anaconda Slime Plant........... 479 1. A Diagrammatic Flow Sheet of Plant............. 480 2. The Slime-Thickening Division................ 480 3. The Concentrating Division.................. 481 4. The Concentrate-Dewatering Division............. 483 5. General Data........................ 484 I. IntRoduction The new slime-concentrating plant at the Washoe Reduction Works, Anaconda, was put into operation during March, 1914. This plant, which has a capacity of 26,000,000 gal. of slime pulp carrying 2,500 tons of solid matter per day, consists of Dorr thickeners and Anaconda multiple-deck slime concentrators. This plant is the culmination of a great deal of experimental work extending over a considerable period of time, which , work will be described briefly in the following pages. II. The Sources and Amount of Slime Up to the beginning of this year, the ore from the Anaconda company's mines in Butte, Mont., has been concentrated both at the Great Falls

Jan 1, 1915

By G. Paquet, E. Godin

"Since the mid fifty's, worlwide pellet production capacity has constantly risen (Fig. 1, Ref. 1 l. There was however at that time no real incentive to decrease production costs but only to produce as many pellets as possible. State of things changed with the iron and steel market recession, starting in 1975, and is currently leading producers to improve pellet quality and to reduce fuel and power consumption.At the Port-Cartier pellet plant, the energy needed for the induration of pellets ranks first in overall operating costs. An important step was made when starting admixing coke breeze in 1980. Oil prices justified the use of coke breeze as a direct replacement in terms of dollar/ton, however, while gaining expertise in using solid fuel a significant decrease in energy consumption was observed (Fig. 2, Ref. 2).In 1985, the ""Centre de Recherches minérales"" was commissioned to undertake research work to investigate the effects of further increasing coke addition to the pellet mix. The positive results of that work led to a 1,5% coke addition plant trial during the fall of 1985. Both laboratory and industrial results are discussed in this paper."

Jan 1, 1986

By J Krahn

In designing climate exposed soil structures such as caps and covers over mine waste it is necessary to include the wetting and drying influences of the local climate in order to accurately predict the net water, vapour and oxygen fluxes across the ground surface and through the base of the covers. The most advanced evaporative flux modelling tools currently available to practitioners have been limited to rigorous one-dimensional models (ie SoilCover) or semi-empirical two-dimensional models (ie Hydrus-2D). It is common practice to use the rigorous one-dimensional evaporative flux model results to develop a surface boundary function that can then be applied within a saturated/unsaturated two-dimensional model. However, this is not an ideal situation and results in a further approximation of the real system being modelled. This paper will highlight the use of a new modelling tool, VADOSE/W, which brings existing, rigorously formulated evaporative flux theory into the familiar setting of a two-dimensional model. The model is enhanced for simultaneous two-dimensional oxygen gas transport analysis, which has direct application in the mine waste industry. A key focus of the paper will be addressing the limitations of one-dimensional analysis for cover systems on sloping and hummocky terrain.

Jan 1, 2003

By O. H. Metzger

This is the first of two papers dealing with construction and use of aerial tramways in the metal-mining industry. It describes practices and equipment used in tramway construction and discusses the design of tramways. The second paper will describe the construction and operation of tramways and give operating costs. ACKNOWLEDGMENTS The author acknowledges the cooperation of a number of cable and tramway manufacturers Who supplied practical manufacturing data and other valuable information. Full credit for formulas used in the design of aerial tramways it given' to Edward B. Durham3/ and F. C. Carstarphen.4/

Jan 1, 1937

By Knight J. L, Baker G

The Wonthaggi coalfield is in South Gippsland, about 90 miles southeast of Melbourne. It is situated on the down-faulted block of the South Gippsland highlands that lies south of the Kongwak fault, between the Powlett River and the sea (Fig. 1). The coal, which is of Jurassic age, occurs in two small, and intensely faulted, limnic basins, that lie on either side of a concealed ridge of Silurian sediments. The coal was first found as thin seams outc1'opping in the cliffs at Cape Paterson, but the seams that are worked at Wonthaggi are concealed beneath a veneer of Cainozoic sands that covers the Jurassic strata, and were found by boring.The c9al seams are worked by the State Coal Mine, which was opened in 1909 to ensure a supply of coal for the Victorian railways, following a prolonged strike in the Newcastle field of New South Wales. The total production from 1910 to June, 1943, amounts to 13,918,800 long tons of coal. The coal seams are faulted to a degree unknown in most coal...

Jan 1, 1944

By Carlos R. Scherpenisse

La voladura es una de las operaciones unitarias en la extracción del mineral, donde se busca un adecuado grado de fragmentación de la roca y se reduzca el costo combinado de las operaciones de perforación, voladura, transporte y chancado primario roca, produciendo a la vez el menor daño posible en las cercanías de ésta. En este sentido, el empleo adecuado del Monitoreo de Vibraciones producto de voladuras, es una técnica que provee múltiples ventajas en términos de examinar en detalle el proceso de la voladura y conocer su eficiencia relativa, su interacción con las cargas adyacentes y en definitiva el rendimiento general del diseño. Por ello, el presente trabajo describe algunos casos de aplicación de la técnica de monitoreo de vibraciones -particularmente en Mina Subterránea y su importancia en el diagnóstico, control, modelamiento y optimización del proceso de la voladura. Asimismo, analiza su potencial en términos de alcanzar substantivas mejoras técnico-económicas, aumentar los rendimientos y minimizar los costos operacionales en esta etapa de la explotación minera.

May 25, 1998

By Robert B. Parsons

"This article is based on a paper presented by Jim Scott at the 1988 annual convention of the Prospectors and Developers Association of Canada. The paper suggests a number of factors that might be taken into account in negotiating royalty terms.IntroductionRoyal ties are a part of mining life in Canada. They are used by many kinds of individuals in many kind s of situations. Prospectors commonly take royalty interests back when they transfer claims to development companies. Mining companies disposing of undeveloped (or sometimes even developed) properties are often paid at least in part by royalties. Royalties are even used by institutional investors with no other connection with the resource industry.Such different royalty holders have different investment goals, different cash flow requirements, and different risk / return preferences. These differences have given rise to a number of different royalty types. These types range from the simplest cents-per-ton royalty (where the operator pays a royalty at a fixed rate per ton milled) to net smelter return or ""NSR"" royalties (where the royalty is based on a percentage of the operator's NSR) all the way to net profit interest or ""NPI"" royalties (where the royalty is based on the operator's bottom-line net profit),The fundamental difference between the many royalty types is in the risk / return relationship. The cents-per-ton royalty, for example, is relatively risk-free. Of the many economic factors which affect a mine, the only one which will affect the royalty holder is the amount of ore physically milled. On the other hand, the potential for significant gains under a cents-per-ton royalty is also very limited. The royalty holder will not share in any increases in the market price of the end product or any cost reductions achieved by the producer."

Jan 1, 1989

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By R. T. Um, W. K. Tolley, J. C. Stauter

A hydrometallurgical process for the recovery of lead from sulfide concentrates is presented The process combines the unit operations of selective dry chlormation, brine leaching and fused salt electrolysis as key steps An overview of the chemistry involved in the process 1s discussed as it pertains to overall recovery.

Jan 1, 1981

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By P. W. Neurath, R. E. Waite

INFORMATION is available on the effect of stress on permeability, coercive force, and hysteresis for a variety of materials' but for the technically important grain-oriented 3 pct Si-Fe' the stress effects are not adequately covered in the literature; in addition, most of the stress data do not permit estimation of what would happen to the 60 cycle watt losses of the material under stress. Direct measurement of these effects therefore has been made and appears to be of considerable theoretical as well as practical interest. Losses were measured on the central 25 cm portion of 40~3~0.035 cm samples which could be stressed in a small tensile machine built for this purpose. Under tension the following effects, illustrated in the figures by a particular example, were observed: 1—"Unstrained" material of commercially acceptable loss level shows no change or a small increase in loss at low elastic stresses. For the sample shown in the figures, this is illustrated during the initial run, where a 7 pct increase is observed (Fig. 1). 2—There is no additional change in loss when the sample is further strained up to the elastic limit (Fig. 1). Within that limit the loss-stress curve is reversible. This is not illustrated in Fig. 1. 3—Even in the plastic range only small increases in loss are observed as long as the sample is kept under stress (Fig. 2, point N); often no increase can be observed (Fig. 1). 4—A large increase in watt losses is observed after removal of the stress subsequent to plastic deformation (Figs. 1 and 2). 5—All, or nearly all, of the foregoing increase in loss due to plastic deformation can be eliminated by a reapplication of tensile stress but returns upon removal of this stress. This is illustrated in the third run (Fig. 3). This run remains within the elastic limit and shows the reversibility of the stress-loss curve under this condition. These findings have been confirmed on large Samples (approximately 200~10~0.035 cm and larger) except that under 1 no initial increase in loss was ever observed on these. The accuracy of the watt loss measurements is of the order of 1 pct. Neither bending of the sample in the tensioning device nor a redistribution of flux along the width of the sample accounts for these results. They therefore must be explained on the basis of either a change in the domain configuration due to stress or a change in the domain wall mobility. Acknowledgment The assistance of Mr. Robert L. TenBroeck with the instrumentation is gratefully acknowledged.

Jan 1, 1956