Search Documents

By J. S. Long

A finite-difference model using a digital computer was constructed to assist in the water management of a proposed oil-shale mining operation in the Piceance Basin in Colorado. The presence of ground water is both a detriment and a benefit for development of the resource. On one hand, dewatering is required because permeable zones are present in and above the oil-shale sequence, and rich oil shale at the proposed mine is as much as 457 m (1500 ft) below the water table. On the other hand, ground water is the most feasible source of water for processing the oil shale. A ground- water model was constructed to simulate the development of an environmentally acceptable water-management system that will satisfy both the mine-dewatering requirements and the water-supply requirements for processing. The ground-water model discussed in this chapter was constructed for the Rio Blanco Oil Shale Co. (RBOSC) by International Engineering Co., Inc., a subsidiary of Morrison-Knudsen Co. The model was applied to evaluate dewatering and water control systems for several open-pit mining plans initially investigated to develop Federal Lease Tract C-a. A collateral application of the model analyses was to project effects of the proposed dewatering operation on the regional ground-water regime in connection with a permit acquisition program by RBOSC. Subsequently, RBOSC has completely changed its mine development plan and has adopted modeling and related techniques more suitable for study of that plan and dewatering operation. The authors of this chapter are solely responsible for the contents and conclusions.

Jan 1, 1979

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By B. H. Kaye

Particle-size Distribution Specifications for Particulates. Feed to and finished products from size-reduction operations are defined in terms of the particulate sizes involved. It is also well to know whether the ultimate individual particle is being measured, or, if any aggregation or agglomeration of particles exists, whether this has been created by the size-reduction operation. The most complete description of a powder is given by its particle¬size distribution. This can be plotted in terms of cumulative percent oversize or undersize in relation to the diameters of particles, or it can be plotted as a distribution of the amounts present in each unit of diameter against the several diameters. It is common to employ a weight basis for percentage, but there are some data in the literature where frequency, or number of particles, is used. The basis of percent¬age, whether weight, frequency, or some less commonly used factor, should be specified, as also should be stated the diameter, its units, and preferably whether determined by sieve, settling velocity, or other¬wise. Fig. I presents two sets of distributions-ore cumulative and the other in unit intervals. The slopes of the 5-µ intervals of the cumulative curves are converted to percent per micron and plotted as a block, or histogram, from which smooth curves are derived. Powder A has a narrower, or tighter, size range for the bulk of its weight than powder B. Both materials have the same weights below and above the size marked by the arrow. Simpler treatments of distribution are possible. In some cases the significant value is the top size. Since the 100% point is dubious, some amount, as 95 or 98%, so specified, can be called top size. In other cases the percent on some sieve helps define coarseness. Merely stating that all, or all but a small percentage, passes a given sieve is inadequate for defining the true fineness or a material. Complete parti¬cle-size analysis to show the distribution is essential for most compari¬sons and calculations. Particle-Size Equations. A number of equations have been pro¬posed to correlate the quantity of a particulate material with its parti¬cle size to obtain a distribution relationship. 's 19 In the literature it is often assumed that a powder must follow some distribution, such as the Rosin-Rammler-Bennett:20, 21

Jan 1, 1985

By Jack W. Carlson

Considering the magnitude of today's public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By Freislich. M., Y. Gordon

"In the changing global market scenario for raw materials for the steel industry, a number of novel iron- and steelmaking process technologies are being developed to provide the steel companies with economically-sustainable alternatives for iron- and steel-making. In addition, the steel industry is also focusing on reduction of energy consumption as well as green-house gas (GHG) emissions to address the crucial subject of climate change. In this context, it is important to assess these critical issues for the alternate iron- and steelmaking technologies that have been developed. This paper presents a comparative evaluation of energy-efficiency and GHG emissions for some selected iron- and steelmaking technologies that are being considered for implementation. In this work, Hatch’s G-CAP™ and En-MAP™ tools that were developed with the main objective of quantifying and qualifying the potential energy savings and CO2 abatement within the iron and steel industry, were employed in the evaluation conducted. INTRODUCTIONThe iron and steel industry continues to transform itself and evolve in the ever-changing global market place – the raw material scenario is constantly changing with respect to quality and quantity (availability), there is stiff competition in both global and local markets, and there is increasing pressure to address global climate change issues, especially since the steel industry is highly energy- and carbonintensive. There is growing importance of steel production in developing countries such as China and India – this means that the steel industry in these countries will play an important role in defining and shaping the future of the industry.Climate change is expected to present new risks to the steel industry with respect to ensuring a sustainable business. Legislators are proposing to limit GHG emission by placing an implicit price on CO2 emission - market-based “cap and trade”, carbon tax etc.. In this scenario, it is important for the steel companies to reduce exposure to climate-related risks and at the same time, find business opportunities within these risks. Thus, there is a need to strategically manage the climate change risks; the key steps to strategically manage climate change risks are presented in Table 1[1]."

Jan 1, 2012

Jan 1, 1891

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By M. R. Louthan, C. L. Angerman

In polycrystalline Zircaloy-2 the orientation of zirconium hydride precipitates is influenced by an applied stress during hydride precipitation; hydride platelets are oriented nearly parallel to a compres-sive stress and perpendicular to a tensile tress. 1,2 A similar effect has been observed in the Ti-H system, where precipitation of the low-density hydride platelets occurred on habit planes made energetically favorable by the application of stress. 3 Recently, stress activation of hydride habit planes in zirconium and Zircaloy-4 was also demonstrated. The hydrides precipitated on {101l), {112l} and (2131) planes in both zirconium and Zircaloy-4; however, no platelets were found near the prism-plane positions in the Zircaloy-4 samples. Investigations at the Savannah River Laboratory, using polycrystalline Zirc_aloy-2 samples, have confirmed the (101l) and (1121) habit planes but also showed that the prism planes were active hydride habit planes. Using single-surface stereographic analysis and back-reflection Laue techniques, most of the previously reported habit planes for a zirconium were observed.4"1 and one additional plane, the (1013) plane, was noted, Table I. All the habit planes observed had the form (101l) or { 112l) indicating that these planes are the habit planes for hydride precipitation in poly-crystalline Zircaloy-2. The specimens used in these studies were cut from large-grained weld areas of seam-welded tubing and were hydrided in either a static steam autoclave at 400°C and 1500 psig or in a modified Sieverts apparatus at 400°C.

Jan 1, 1967

By Edward W. Parsons

The explosive-anchored rockbolt was field tested in six mines where rock conditions varied from incompetent shale or mudstone through fairly soft sand-stone to firm sandy shales. The purpose of the testing was to document, under a wide variety of conditions and in comparison to other rockbolt anchors, the quality of the anchorage produced by the explosive-anchored bolt. In addition, the length, strength, and design of the explosive charge necessary to produce positive anchorage up to the yield strength of the weakest component of the bolt were determined. A l4-inch length beaded explosive charge was found to be suitable, in general, in relatively weak strata, and the length can be reduced in more competent strata. Of the 127 explosive?-anchored bolts tested, 118 bolts produced an evaluated anchorage in excess of 17,000 pounds. Only 4 of 43 expansion-shell bolts and 4 of 14 wedge bolts produced anchorage this good. In preliminary tests, properly coupled explosive-anchored bolts did not ignite an explosive gas mixture. Some minor phases included in the investigation were as follows: (1) effect of explosive-anchored rockbolt on surrounding rock; (2) effect of time on anchored bolts based on torque tests; (3) effect of submersion in water on rockbolt anchorage; (4) pull tests to higher loads; and (5) ignition tests.

Jan 1, 1965

"Prior to the publication of the General Report of the Miners' Phthisis Prevention Committee of South Africa in 1916 little attention was paid to the dust hazard and the necessity for its suppression in the underground workings of the Broken Hill mines. Such precautions as were observed for the elimination of dust were related rather to the prevention of lead poisoning, which, in the early days of Broken Hill when large tonnages of lead carbonate ore were being won, was rather prevalent. Ventilation and hygiene followed the general practice in this and most foreign countries.This paper covers incidence and action since 1918, considering medical aspects and operating aspects. "

Jan 1, 1947

By G. J. Saulnier, K. E. Goddard

The US Geological Survey has developed mathematical modeling techniques to assess potential impacts on the hydrologic system resulting from mining of coal and oil shale in northwestern Colorado. Potential impacts of oil shale mining on groundwater hydrology have been simulated using a quasi-three-dimensional, finite-difference model. The model has been used to simulate hypothetical mine dewatering operations at two proposed oil shale mines. Dissolved-solids distribution and solute transport were simulated with a three-dimensional, finite-difference model that was used to evaluate the effects of flooding in hypothetical abandoned mines. The potential impacts of coal and oil shale mining on water-sheds were investigated using a digital watershed model. This deterministic physical-process model predicts responses of the hydrologic system to modifications resulting from mining in basins having snow as the major source of runoff and recharge. Potential impacts of coal development on surface water quality were investigated using a river quality assessment model. The models developed by the US Geological Survey have been useful in defining the potential effects of mining in northwestern Colorado. They are an important first step in analyzing the existing data base and in predicting impacts and new data needs. The models may not be totally applicable on the local scale but are very meaningful on the regional level.

Jan 1, 1983

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By S. J. Hardison

IN the fall of 1912, the appearance of water in the oil of the Nevada Petroleum Co., Coalinga, Cal., made necessary the installation of a dehydrating plant to reduce the water below the 3 per cent. limit prescribed by the agency. Unlike the mining industry, technical literature of the oil industry is limited and extremely unsatisfactory. Until the recent efforts of the Petroleum and Gas Committee of the American Institute of Mining Engineers, no concerted movement has been instituted to secure publication of papers dealing with the problems of the oil business, and because of the additional fact that dehydrating of oil has not been practiced in California to any extent up to comparatively recent time, it was found necessary to experiment in order to determine the most satisfactory plan for this purpose. It is easy to write regarding successful enterprises, but, while not so pleasant, it is equally desirable to write of failures so that others may be saved the loss incident to such investments. The water in this oil occurs both free and as an emulsion. Free water easily settles out, but the emulsion requires treatment. So far as can be determined, the emulsion consists of globules of water surrounded and enveloped by a film of, oil. Starting with this hypothesis, the theory has been evolved that in order to break up this emulsion the water must be heated at least to boiling point, when an explosion takes place destroying the globule. Unfortunately, this condition was not recognized in the installation of the first plant, which was planned on the following lines: A heater was arranged so that all the oil from the wells could be heated before reaching the shipping tanks, these being already fitted with coils for steam heating. Tanks were filled with about 4 ft. of water, live steam was turned into the coils and the water brought nearly to the boiling point, when the heated oil was run in. This for a time was partly successful, but the length of time necessary to apply this heat was too great for practical operating.

Jan 3, 1915

By R W. Hutchinson

Cupreous pyrite deposits in Cyprus have many geologic similarities to Canadian massive sulphide copper-zinc ores as well as certain significant differences. A comparison of the Cyprus and Canadian deposits indicates a complex genetic history for the latter and suggests that their origin should be re-examined. The Cyprus ores occur in subaqueous extrusive rocks near and at the top of a Cretaceous volcanic pile or igneous complex. The rocks have not been deformed, nor have they been deeply buried or deeply eroded. Apparently the ores formed near or at surface in the top of the volcanic pile by a volcanic-exhalative process and from an ore-fluid of volcanic derivation. The Canadian deposits are of comparable composition and have similar geologic set-tings, but occur in the most ancient Precambrian rocks. Their enclosing Keewatin greenstones have, in most places, been deformed, regionally metamorphosed and invaded by granitic intrusions. Comparison suggests that the Canadian ores also formed initially near surface in ancient Keewatin volcanic complexes by a syngenetic, volcanic-exhalative process. Subsequently, during orogenesis, they were deformed, remobilized under conditions of elevated pressure-temperature and re-emplaced as epigenetic bodies into

Jan 1, 1965

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By J. Schmidl

In non-ferrous metallurgy the service life of refractory materials typically ranges from several weeks up to three years or more and is strongly dependent on operating conditions. To support our customers with the most viable refractory solution for their needs RHI Magnesita follows a structured approach of thermo-chemical calculations, experimental evaluation from lab scale up to industrial field tests and post-mortem analysis of used refractory materials. This paper will give an overview of the RHI Magnesita refractory selection process and the most recent developments of the experimental setup for the so called HF-IF test. This is a dynamic corrosion test that allows to determine fundamental properties of different refractory material types under process conditions subjected with respective customers process materials. The HF-IF experimental procedure is an excellent tool to simulate refractory wear in industrial processes, diminishing risks associated with plant trials and support decision making to choose the optimal refractory solution for the customer.

By Karl S. Vorres

Coal my not seem like it, but it is a perishable commodity. The basic coal scientist cannot always replicate earlier experiments with a given sample because of changes that have taken place in the sample. This has led to a stated need for stable samples Coal looks like a uniform black solid to many people, but it does vary in its composition from state to state and mine to mine it also can be shown to vary significantly within a mine or seam. These variations have led to a stated need for consistent samples.

Jan 1, 1985

By Frank Milliken

IN September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1007 to 1019. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was dissemi-nated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was prob-ably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a com-plete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof com-prised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. 1, which gives percentages of tonnage and copper content.

Jan 1, 1940