Search Documents

By F. Romero

In the last four years, Compañia Minera Doña Ines de Collahuasi has been working in the application of advanced multivariate statistical techniques for the improvement of the metallurgical processes. In this paper the main conclusions for the application of multivariable analysis to the EW process are presented; including the identification of (target) process patterns according to throughput and quality criteria. Based on the process patterns, process variables hierarchies were identified by selecting the most influential ones, as well as to identify and isolate the root causes of pattern deviations and sub-standard operating conditions, cause-effect relationships were established, leading to the definition of process policies and controls to give early corrections to potential failures. The analysis was focused on cathode quality, specifically in its sulfur content, using an empirical model based on those variables that from a phenomenological and statistical stand point appeared to be the most influencing ones.

Jan 1, 2007

By J. M. Boxall

The electrolytic zinc plant at the Bartlesville division of Z.C.A. originally used lead anodes containing only 0.25% silver because only H.G. zinc and alloy was to be produced. In 1984, a small addition of strontium carbonate was made to control the surf ace morphology of the cathodes which reduced short circuits and increased current efficiency. Later a drastic reduction in colloid addition further reduced short circuits. Increased strontium additions allowed the production of some S.H.G. zinc. Increasing the silver content of the anodes reduced the lead in cathodes only slightly. More important, the anode scale that was not removed during anode cleaning, entered the electrolyte and contaminated the cathodes with lead. A piping system has been installed to purge the contaminated electrolyte directly back to the leaching section. This has allowed the plant to produce S.H.G. zinc consistently.

Jan 1, 1990

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

By D. A. Crerar, R. L. P. Kleinmann, R. R. Pacelli

A bacterium, Thiobacillus ferrooxidans, is of prime importance in the formation of acid drainage from pyritic material. Above pH 4.5, T. ferrooxidans increases initial acidification; below pH 4.5, it allows acidification to continue by oxidizing Fe2 +. Below a pH of approximately 2.5, the activity of F3+ is significant and results in steady-state cycling between oxidation of pyrite by Fe3 + and bacterial oxidation of Fe2 +. Laboratory and field tests demonstrate that inhibition of T. ferrooxidans by controlled release of anionic detergents can inexpensively reduce pyrite oxidation and acid formation.

Jan 1, 1982

By Carlton H. Baab

In June, 1981 the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the U.S. coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent". Until recently, clean coal has had a low selling price and satisfying the purchasers' specifications required only minimum cleaning. However, it is becoming more apparent that the increases in coalfired utility power plants forced outage rates are relative to the deterioration in the quality of fired coal. Utility companies are becoming aware of the economic value of reducing the variability of ash, moisture and sulfur in steam coal purchase orders. New contracts are currently being negotiated between electric utilities and coal producers that include provisions for increased penalties if the product does not meet specifications. With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. This paper discusses the various types and applications of nuclear instrumentation currently in use in the coal preparation industry.

Jan 1, 1983

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By C. S. Kucukkargoz, A. Bhalla

"The solid-state reduction of ilmenite concentrate with graphite was studied under argon atmosphere at temperatures between 1050°C and 1350°C. The rate of reduction increased with increasing temperature and decreasing particle size, with the maximum extent of reduction found to be 80% at 1350oC with a particle size in the range of -106 +90 µm. The activation energy for the reduction reaction was calculated to be 257 kJ/mole. The trivalent iron oxide was reduced first to divalent iron oxide and then to metallic iron. An annular ring of a partially reduced oxide phase containing metallic nuclei was formed around the core of ilmenite, which grew in size as the original ilmenite core shrank with progressive reduction. The reduction of titanium dioxide also took place during this stage, which produced the Magneli oxides in the form of TinO2n-1. The metallic phase had very high Fe and low Ti contents throughout the reduction, whereas the partially reduced oxide phase adjacent to the metallic phase was high in Ti and depleted in Fe. The metallic phase globules formed during this stage were small and are considered suitable only for leaching and not for other concentration processes. The core of the particle generally retained the composition of the original ilmenite. The purpose of this work was to remove iron and increase the titanium oxide content of the ilmenite to produce a high-titanium containing charge for subsequent smelting.IntroductionThe titanium-bearing minerals ilmenite (FeTiO3) and rutile (TiO2) are the primary natural raw materials used in industry to produce titanium metal and titanium-based products. The common titanium-bearing minerals are ilmenite, rutile, anatase, brookite, leucoxene, arizonite, and perovskite. Although the formula of ilmenite is commonly expressed as FeTiO3, the mineral can accommodate Mn and Mg, which are chemically bound in the form of (Fe,Mn,Mg)TiO3. Ilmenite concentrate can also contain Fe2O3 and Al2O3 in addition to the physically separable oxides such as SiO2 and CaO. The crystal structure of ilmenite is an ordered derivative of the corundum structure with a trigonal-rhombohedral symmetry. Fe2+ and Ti4+ ions occupy the octahedral sites, leaving the tetrahedral sites unoccupied. In each FeTiO3 unit, there are three O2- ions creating three octahedral sites, two of which are occupied by Fe2+ and Ti4+ (Wilson et al., 2005)."

Jan 1, 2017

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By D. S. Holmes

Biological processes for metal solubilization and ore beneficiation are in widespread use today. There are also some promising new applications of biotechnology in the areas of metal concentration and toxic metal cleanup. Recent progress in genetic engineering promises both to revolutionize the existing biological process and to expedite the adoption of the new biological applications. But before it can do so effectively, progress must be made in many areas of fundamental research and in biochemical engineering. These issues are addressed with special reference to the biotechnology of semi-enclosed containers (bioreactors), dumps, heaps, in situ and under- ground leaching, and with respect to the biotechnology of metal concentration. Finally, certain biological considerations for bacterial strain improvement are discussed.

Jan 1, 1987

By Harold S. Morgan

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is being developed in southeastern New Mexico by the United States Department of Energy as a research and development (R&D) facility to demonstrate the safe disposal in salt of radioactive wastes resulting from defense activities. As part of the WIPP R&D program, a series of in situ tests will be performed to determine the behavior of drifts and storage rooms in the creeping salt medium (Matalucci, et al. 1982). Data obtained in these tests will be used to evaluate and improve numerical models used to compute the structural response of these drifts and rooms. Stress has been proposed as one of the parameters to be measured in the tests, and borehole inclusion stressmeters have been included in the instrumentation package. Cages of this type provide an indirect measurement of stress change in that they actually monitor borehole displacements which are then related to changes in the in situ stress away from the borehole. The relationship between stress and displacement is highly dependent upon the constitutive behavior of the rock in which the gage is emplaced. This relationship is well understood for rocks with linear stress-strain behavior (Fossum, et al, 1976), but, for creeping rocks like salt, the relationship has yet to be determined. Thus, inclusion gage response in salt must be investigated fully before stress measurements from the WIPP in situ tests can be used for comparisons with computed stresses The calculations presented in this paper were performed as part of an investigation of inclusion stressmeter performance in salt. They focus on the strain gaged stressmeter (SGS) (Cook and Ames, 1979) and on a hypothetical solid cylindrical inclusion with variable stiffness Issues addressed include the effects of creep and the effects of gage stiffness on stressmeter output for various loading conditions. The

Jan 1, 1984

By R. W. Raymond

I desire to call the attention of members of the Institute to a new method of plotting and determining faults in mineral deposits, suggested by Prof. Hanns Hoefer, lately of the Mining School of Przi-

Jan 1, 1882

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By C. A. Wiggins, J. M. Kennedy

The Benbrook Connection tunnel forms approximately 6,666 m (19,560 ft) of17,678 m (58,000 ft) of raw water pipeline connecting Lake Benbrook with the Rolling Hills Water Treatment Plant. This connection is designed to minimize costs to the owners, the Tarrant Regional Water District, for providing raw water to its’ various clients. The geological formations through which the tunnel passes and the design requirements resulted in some-what unique applications of initial ground support systems which were modified by the con-tractor to optimize the mining operations. The pipe sections, fabricated in 12 m (40 ft) sections, are concrete lined and coated steel pipe. Construction of the work shaft and tail tunnel was also modified to suit the contractors methods. A Lovat universal TBM was chosen to excavate through the various rock types. The pipe sections will be transported using beam carriers.

Jan 1, 1997

By Edmund M. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence-the total absence of noise except for one's own breathing and scuffing of boots on the bottom. An underpound mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working in the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969." As [Fig. 1] indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which govern noise exposure in many industries. In most industries noise exposure is not a constant value. Noise emitted from coal mining machinery varies widely, and therefore interpretation of compliance is not a simple matter. Time, environment, instrumentation and machine productivity, as well as the designed machine characteristics affect the results. It is the purpose of this paper to present the underground coal face machinery noise problem from a manufacturer's point of view. Manufacturers are very much aware of their responsibility to alleviate the noise problem. Not infrequently, orders are received from coal operators that a given new machine must comply with "The Coal Mine Health & Safety Act" noise regulations. Such a request is indicative of the misunderstanding which exists with machine users, while indicating their desire to comply with the law. Obviously, if all machinery could be designed and used at some arbitrary low noise level, it would be possible to simplify the regulations. However, there still remains the pervasive problem of existing machines. Extensive investigation to create practical retrofit kits for existing machines, to substantially reduce noise have been only marginally successful. Certain machine mechanisms are inherent noise makers. The only really good solution is to substitute a quieter mechanism. Such overall new designs have been undertaken, and several examples are mentioned later in this paper. Before describing machine noise problems, it is necessary to define noise values. Noise levels are measured in decibels. The designation "DBA" is decibels measured on the "A" scale, or one in which the frequency sensitivity of the instrumentation is about the same as the human ear. The numbers are often misinterpreted because it is a logarithmic, rather than an arithmetic scale. In comprehending the numbers, it should be remembered that any increase of 3 dB doubles the sound power. In practical terms this means that two noises of equal power at the same distance away increases a dB reading by three. Consider [Fig. 2] showing a simplified case of a worker on a machine subject to

Jan 1, 1980

By John L. Lamont, Walter Crafts

AN investigation has been made of the multiplying factors for some of the more common alloying and deoxidizing elements for use in calculating hardenability of steel according to Grossmann's method.1 The factors for manganese, silicon, and aluminum that were reported in an earlier communication2 have been confirmed by microscopic determination of the half-martensite structure rather than on the basis of an empirically determined hardness corresponding to a half-martensite structure. Measurement of ideal critical diameter by microscopic examination was found to he necessary for other alloying elements, and multiplying factors for nickel, chromium, molybdenum, zirconium, vanadium, titanium, and boron have been determined. The nature and order of magnitude of the multiplying factors reflect the effect of the alloying elements on the structural character of the steel. Except for nickel and vanadium, the multiplying factors agree fairly well with previously published results. Good correlation between actual and calculated ideal critical diameters has been found in developing the multiplying factors and in checking the results against fairly simple steels. However, some discrepancies have suggested the need for a more thorough study of low-carbon and complex steels. TESTING PROCEDURE The investigation was conducted principally on steels made at the Union Carbide and Carbon Research Laboratories, Inc., in high-frequency induction furnaces using Armco iron and standard alloying materials. However, a few open-hearth steels were used in establishing the effect of nickel, and the hardenability factor for boron was based primarily on open-hearth steels. All bars were normalized prior to the machining of Jominy hardenability specimens. The Jominy test was carried out under conditions standard for the test.3 Austenitizing temperatures judged to-be-appropriate for the composi¬tions of the steels were used., Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Residual amounts of phosphorus, sulphur, nickel, chromium, molybdenum, and copper were determined on only one heat of each group made with the same materials during the same period. "Acid-soluble" aluminum and zirconium rather than total amounts were determined, as it is considered probable that the acid-soluble amount is more representative of the effective alloy. As tin was present to the extent of only 0.002 per cent, its effect was neglected. The method used to determine boron in the steels shown in Table 9* was developed by Galen Porter, Vincent Napoleon, and Thomas R. Cunningham,of the Union Carbide and Carbon Research Laboratories, Inc., and is. a modification of J. Naftel's procedure for boron in soils

Jan 1, 1944

By Marvin Lee

Kansas continued holding, for its seventh year, the fourth position in the list of oil-producing states. The crude-oil production, according to purchaser's reports to the State Corporation Commission, was 40,008,940 bbl.; as assembled by the Oil and Gas Journal, 41,305,768, and by the U. S. Bureau of Mines, 41,942,000 barrels. Increase of production from 1932 was largely due to greater stability of the industry, and increased return of demand for Kansas oil, caused by the addition of Federal assistance in national production regulation which reduced illegal production, of some areas out of Kansas, that had been destructively competing with Kansas crude or its refined products, at less than cost of production. Prices continued to advance from the lowest level of 25c per barrel during part of May and June, until by the end of September 36" gravity crude had reached $1 per barrel and continued at this price the remainder of the year. Price stability, for a period greater than in previous years, has brought renewed confidence to those producing oil and has led to renewed interest and increased purchases of Kansas leases. Drilling was confined chiefly to the number of wells necessary to protect from offset and other drainage in the field and to meet the requirements of expiring lease contract deeper areas in Mid-Continent, are an added inducement to exploration. The renewal of interest in the search for new fields in Kansas is already apparent and 1934 will probably see more wildcatting than for several years. This is due both to the expiration of leases on large blocks and to actual demand of the industry for new fields. Exploration for favorable areas is being actively conducted by the various methods of surface, subsurface and core drilling and geophysical work. Much of western Kansas cannot be mapped by surface study and geophysical exploration has been of considerable assistance and has led to a large use of the seismograph. Several companies are conducting seismograph surveys and leasing on findings already secured. Development under the more favorable conditions of 1933 can be readily seen by the comparison of the following reports for the last weeks of December in the respective years.

Jan 1, 1934

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10 to Sept. 10, 1915: Members ACOSTA, JOSE NICANDRO, Min. Engr. and Chem., Shannon Copper Co., Gleeson, Ariz. ANDERSON, AMIL. ABNER,. Met Homestake Mining Co., Lead, S. D. BARB, P. A Apartado 92, Pachuca, Hid., Mexico. BERGH, SVEN VILHELM,. Min. Engr Rorstrandsgatan 32, Stockholm, Sweden. BOAS, Ross H., Min. Engr:, Care Highland Boy. Mine, Bingham Canyon, Utah. BONSALL, JAMES MALCOLM,.Chem., Copper Queen' Reduction, Works, Douglas, Ariz. BOWLES, Ross., Supt. Of Smelters,. Granby Min. & Smelt. Co., East St. Louis, Ill. BRIGHT, GRAHAM, Engr., Westinghouse Electric & Mfg.. Co., East Pittsburgh, Pa. BUTLER, RICHARD,. Min. Engr., Mines. Supt., Lindal Moor Mines, Ulverston, Lancashire, England.

Jan 10, 1915

The nineteenth regular meeting of the Rocky Mountain Coal Mining Institute at Rock Springs, Wyoming, was called to order in conjunction with the Wyoming State Safety and First Aid Meet, at 2 p. m., Thursday, August 7, 1924, by President William Littlejohn of Castlegate, Utah. Meeting opened by invocation by Father Welsh. Address of Welcome by Mayor P. C. Bunning and key to city presented to President Littlejohn. Response to address, of welcome made by President Littlejohn. Minutes of the last regular meeting read and approved. Report of officers: Financial statement by Secretary-Treasurer Shubart, who stated that there was $1,225.68 in the treasury and requested that the report be referred to an auditing committee for examination and approval. Motion by Mr. Pryde that the report be referred to an auditing committee. Seconded by Mr. Robinson. Carried. A committee of three, consisting of Messrs. Murphy, McKeehan and Gibson, were appointed by President Littlejohn to examine the report, and approve it. As no time was found during the meeting, the Committee was instructed to report later by mail. Report of Standing Committees: Mr. Pryde stated that the report of the Safety Committee would he presented at the morning session, August 8th. Report of Special Committees: None. Unfinished business: President Littlejohn stated that some action should he taken on the interchanging of certificates in the four states of New Mexico, Colorado, Utah and Wyoming. A committee should probably be appointed from each of the states, and the matter left in their hands to try if possible to get their legislators to put some law into effect which will make the certificates in all these four states interchangeable. President Littlejohn also stated that the subject had been brought up, through correspondence, of changing the emblem of the Rocky Mountain Coal Mining Institute, which is the old oil lamp, and that he had had a letter from Mr. C. M. Schloss, who stated that inasmuch as the old oil pit lamp was symbolic of mining it should be retained so that unless someone had any

Jan 1, 1924

By Zachary Mayer

Agenda ? Kidd Mine ? Background ? Problem & Opportunity ? Challenges associated to depth - Production Rates - Productive Work Time - Operational Delays - Transfer Levels - Mucking Time - Impact on Hoist ? LHD Automation ? Sandvik AutoMine Lite ? Expected Benefits Kidd Mine - Background ? Located in Northern Ontario, Canada ? Underground base metal mine operating since 1966 ? Total 148 Mt mined (2.31% Cu, 6.08% Zn, 75 gpt Ag) ? 2.35 Mt/Y from stopes as deep as 9500 ft (2.9km) below surface ? Mining method: blasthole open stoping ? Mine/Mill: 1263 employees and contractors ? 2012 National John T. Ryan Safety Award

Aug 1, 2013