Search Documents

By H. Margolin, E. Ence

In order to understand the effect of zirconium on properties of Ti-Cu-A1 alloys, Ti-Zr alloys were examined for the presence of ordering or compounds at the following compositions in weight percent: 24.1 pct Zr (lZr:GTi), 32.2 pct Zr (lZr:4Ti), 38.8 pct Zr (lZr:3Ti), 49.0 pct Zr(1Zr:ZTi). Alloys were prepared as 15-g buttons by non- consumable arc melting under argon atmosphere from Bureau of Mines titanium (Bhn 63) and Reactor Grade zirconium (Bhn 150). Weight losses during melting did not exceed 1 pct of the initial button weight. Prior to heat treatment, buttons were hot-rolled at 600" to 700°C to rods of about 6 mm diam. Contamination after hot-rolling was found to extend to a depth of less than 0.5 mm. Specimens for heat treatment were wrapped in molybdenum sheet, annealed in argon-filled quartz capsules, and quenched by breaking the capsules under iced brine. Annealing times were as follows: 700°C — 7 days; 600°C— 14 days; 575°C-1 and 2 months; 525°C-2 months; 500°C-2 months. Prior to heat treatment, all Ti-Zr alloys were vacuum annealed at 900°C to remove hydrogen. The reanneal of 575°C specimens for an additional month produced no observable microstructure changes. The results obtained by microstructure and X-ray diffraction are shown in Fig. 1, together with data of Hayes et al.' No other phases than a or P were found. Small amounts of retained P were detected by X-ray in the 49 pct Zr alloy. The data of the present investigation suggests that ß and a transus boundaries are at considerably lower temperatures than those of Hayes et al. The work of Hayes et al. is based on sponge titanium and Bureau of Mines zirconium, both of which contained 0.15 pct 0. Since melting was performed in

Jan 1, 1962

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,' Si,' Ni,2-5 CO,'-', Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry's law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.'2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By Gerald Edmunds

The liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the composition of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. Apparatus By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 13/4-in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 181/2 in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By Luc Rombouts

The resources and reserves calculation of marine diamond deposits should be based on a systematic sampling grid. The distribution of the sample grade results tends to be very skew and has a large variance. A bias is easily introduced due to the fact that the grade distribution of the samples is very different from the grades of the area of influence. The temptation is always there to extrapolate the highest grade samples simply to their area of influence. If this is done, the higher grade areas will be systematically overestimated, while the lower grade areas will be underestimated. Such a bias should surely be avoided by weighing the sample grades in such a way with their neighbours, so that the estimated grades have a similar distribution as the grades of the blocks. The grade distribution of small mining blocks tend to be lognormal-like. If the coefficient of variation is known, i.e. the standard deviation divided by the mean, then the grade distribution of the small mining blocks is relatively well-defined. The distribution of the diamonds within the deposits can be simulated, based on the histogram of the sample results and on the semivariogram. The diamonds tend to cluster in trapsites. From the semivariogram and the histogram, the average size and spacing between trapsites, and the grade distribution within the trapsites, can be calculated using the model of the General Family of Discrete Distributions. Using such a simulated deposit, the grade distribution for different block sizes can be obtained. The grade distributions become more lognormal-like with increasing block sizes, as the trapsite effect is reduced.

Jan 1, 1998

By Paul Eimon

In the world of minerals exploration, computer-oriented data storage and retrieval methods are being talked about, studied and researched. The goal is to facilitate the recording, collating, indexing, recovery, and analysis of mineral deposit-prospect data. A survey has been made of the various report forms, suggested outlines, and computer coding forms that are currently used in mineral exploration to index and/or describe mineral deposits and prospects. These forms have a number of common characteristics: location, commodities, type of deposit, host rock, etc. Such basic mineral deposit-prospect "data units" are part of most exploration programs. "Data units" may be comprehensive bound published descriptions of mines or mining districts or 3x5 file cards or elaborate computer coding forms being developed in Canada. Initial attempts to develop computer-oriented information systems have run into the same roadblock: the lack of a body of organized, processible data describing the basic qualities of mineral deposits and prospects. To solve this problem, international committees are considering coding forms, world-wide semantics, and rules or standards for data collection and description. It appears that mistrust and lack of understanding of the computer; fear of loss of proprietary information; and disagreements over terminology are distorting the picture of what has to be done if the mining industry is to grow into more meaningful information systems for mineral exploration.

Jan 1, 1969

The greatest single obstacle in the path of constructive action in making conservation a reality is the inherent discord in the hearts of men. A perfect society doubtless is many millenniums removed from the present generation, but it must be admitted that progress toward a conservative use of our natural heritage with the altruistic concept of the greatest good for the greatest number for the greatest time can be attained only by a society in which discord is reduced to a minimum compatible with the limitations of human nature. Daily industrial discord is witnessed between management and labor which passes the bounds of arbitration and results in stoppages of production, waste of productive capacity, idle capital, idle labor, and the complete loss of the most unrecoverable element of all-time. The conservation of material things cannot progress independently of the conservation of the efforts of the human worker, and the results of these efforts are proportional to life itself as measured in hours and years. Unfortunately discord passes international boundaries, and the story of war is as old as the story of mankind. Our recent attempts of international control of nations appear to be dismal failures. The prestige and power of the League of Nations and the present United Nations declined rapidly after they were unsuccessful in stopping the first outbreak of hostilities after their or-

Jan 1, 1950

By J. D. Bateman

At Giant Yellowknife, where high grade gold-bearing orebodies are highly irregular in shape, geology has been applied extensively to the mining of ore. The classical functions of the mine geologist in the fields of exploration and mine development have been extended to guide ore extraction, ensuring "clean" mining and effectively reducing waste dilution.

Jan 12, 1951

By Sir Robert Hadfield

Introduction.-I esteem it a great honor to be asked by this Institute to give them an address chiefly devoted to metallurgy. While it is with great regret that I find myself unable to be present to deliver this in person, I take this opportunity of wishing your society every success in its continued career of usefulness to the metallurgists of the great Republic. To be elected, eight years ago, along with Dr. J. E. Stead, F. R. S., as one of your Honorary Members, was a privilege which I greatly esteemed, for I consider that no society in America has done so much as ours for the advancement of metallurgy. Those who have Served our Society.-Where many have served so well, it is difficult, without appearing to make unavoidable distinctions, to select names from those of your members who have done so much for the cause we have at heart-the advance and progress of metallurgy. As typical, however, and not in any way meant as a complete list, there are among others the following names which in the past and to-day stand out prominently in this science of ferrous metallurgy. With most of those now mentioned I have personally come in contact, or by correspondence in some few cases, and have exchanged views, since I first came over to America 30 years ago. Holley; Jones; Weeks; Andrew Carnegie; Thomas Carnegie; Fritz; Sterry Hunt;. Egleston; Maunsel White and Taylor, who did so much for high-speed tool steel, and helped to revolutionize machine-shop practice; W. J. Taylor; Robert Hunt; Alfred Hunt of Pittsburg, who did so much in the early history of aluminum, and, alas! did. not live to see the wonderful progress which has been made in that particular branch of metallurgical industry; James Douglas; C. B. Dudley; Birkinbine; Howe; Metcalf; Barus; Langley; Raymond; P. H. Dudley; H. H. Campbell; W. R. Webster; E. D. Campbell; Talbot; Spilsbury; Gayley; Dinkey, under whose supervision and responsibility modern armor has been so successfully produced in this country, which the writer can testify from personal knowledge of , test results possesses very high Figure of Merit; Schwab; Kennedy; Wellman; Garrison; Wood; Moldenke; Webster; Swank; Unger; Richards; Sauveur; Strat-

Jan 5, 1914

By R. H. Richards, A. E. Woodward

In Rittinger's Aufbereitungskunde of 1867 occurs (p. 195) the following table, which shows the rate of falling in water of fragments of minerals, of irregular shapes and of five different specific gravities: Diameter of particles in millimeters. 10 8 6 4 3 2 1 .5 Sp. Or. Velocity in meters per second. Auriferous silver, 16..9 .8 .7 .57 .5 .4 .29 .20 Galena,. ..7.5 .62 .55 .48 .39 54 .28 .20 .14 Pyrites,. ..5.0 .49 .43 .38 .30 .26 .22 .15 .10 Quartz,. ..2.6 -30 .27 24 .19 .17 .14 .10 .07 Coal,. ..1.3 .13 .12 .10 .08 .07 .06 .04 .03 With the purpose of extending this valuable table, to cover a larger number of minerals and sizes of each mineral, and of making it more easy of application in deciding upon a sieve-scale for any group of minerals, we have prepared the curves of velocity of fall of bodies in water shown in Plates I., XI., 111. and IV., using Rittinger's formula V= 2.44d(8 —1) where V= velocity in millimeters per second. " D = diameter of particles in meters. " 8 = specific gravity of the mineral. These curves embrace a large number of specific gravities, and for each specific gravity the relation of the diameter of the mineral particle to the velocity of its fall in water is given for all diameters and velocities used in practice. The second diagram is an enlargement of the lower left-hand corner of the first, the third bears the same relation to the second, and in like manner the fourth to the third. Plate I, therefore, covers the work of the coarsest jigging 2 inches in diameter; and under

Jan 1, 1890

By David Lewin

The journey toward cleaner coal-fired power generation is driven by technological improvements, more stringent regulations around greenhouse gas and other air emissions, and the potential of one of Canada?s most abundant resources. Within this context, EPCOR is leading efforts to commercialize gasification technology to produce electricity with near-zero emissions. By turning coal, oxygen, and water into synthesis gas through a gasification process ? and then capturing CO2 ? it is possible to dramatically reduce greenhouse gas and smog-related emissions. EPCOR is conducting front-end engineering and design work on an Integrated Gasification Combined Cycle technology (IGCC) utility-scale plant ? in conjunction with the Canadian Clean Power Coalition ? at its Genesee site, west of Edmonton. EPCOR, the Alberta Energy Research Institute, and Natural Resources Canada have each contributed $11 million to the $33 million project. A critical element of the project features the capture of CO2, which would be piped underground for long-term sequestration, or for use in enhanced oil recovery (EOR). The combination of IGCC and CO2 sequestration, at this scale, has not been used anywhere else in the world.

May 1, 2008

By Rufus L. Chaney

A new technology is available to the Ni mining and remediation community to “phytomine” Ni from mineralized or contaminated soils using rare plants which hyperaccumulate Ni to over 1% of shoot dry matter. Research has identified useful plant species, and even bred improved cultivars of Alyssum murale and Alyssum corsicum for commercial phytomining in temperate regions. All agronomic practices (fertilization, soil amendments, planting and harvest methods) needed for economic phytomining were identified to attain high yields and high Ni concentration in the biomass. In tropical regions, other species are available such as Phyllanthus which accumulate over 1% Ni in dry shoots. These species are perennial so they regrow after annual cutting to harvest biomass. Expiration of our patents on the technology opens the opportunity for other organizations which control Ni rich natural soils or contaminated soils requiring remediation to commercialize the technologies. Inexpensive methods to remediate/revitalize Ni contaminated phytotoxic soils using agronomic approaches have also been developed and demonstrated at Port Colborne, Ontario, but adoption is delayed until formal agreements with government are completed. These new simple remediation and profitable phytomining technologies can obtain Ni from soils which contain Ni well below levels considered economic for current mining technologies, and the plants biopurify the Ni so it is easy to recover Ni metal from plant ash by pyrometallurgical or hydrometallurgical technologies. Although increasing pH decreases the solubility of Ni in all soils, raising pH increases Ni accumulation by Alyssum species. Hence usual chemical extraction methods for phytoavailable soil metals such as the DTPA- or NH4-OAc-extraction cannot predict Ni accumulation by Alyssum species.

Jan 1, 2016

By Cadwallader Evans

THE American Institute of Mining Engineers was organized in the anthracite region of Pennsylvania by men who were primarily interested in anthracite. Its first meeting, at Wilkes-Barre, Pa., in the Northern Anthracite field, on May 16, 1871, resulted from a call sent out by three outstanding men of the anthracite .industry: Eckley B. Coxe, R. P. Rothwell, and Martin Coryell. The best known of these was Eckley B. Coxe, who was the manager of large hold¬ings operated by him and his family,. and who is remembered as the inventor of a special grate for burning very fine anthracite, known as the Coxe traveling grate, which is still very widely used. R. P. Rothwell was a well-known consulting engineer of the region, as was Martin Coryell, who was associated with another well-known anthracite family, the Pardees. There is no record of the discussions that resulted in this initial meeting, but it is safe to assume that the formation of the Institute was largely influenced, through appreciation by the founders, of the necessity for a free exchange of information covering the whole of the mining industry. One of the rules adopted at the first meeting was:

Jan 1, 1947

By Jorge Rodríguez Velarde

Dado que la extracción de metales exige revisar la tecnología existente para así proveer de los metales necesarios que se requieren para suplir esas exigencias. En ese sentido, el presente texto describe la lixiviación bacteriana como la tecnología de vanguardia para recuperar elemetos metálicos a partir de materiales mineros marginales. Los sulfuros metálicos tienen propiedades electroquímicas que pueden transferir electrones, generando reacciones tipo redox. Por ello, los thiobacillus thiooxidans y los thiobacillus ferrooxidans para su metabolismo, requieren ganar energía de aquellos electrones ubicados en orbitales de un alto nivel energético. De esta manera, una bacteria puede catalizar un proceso redox con un sulfuro metálico. La pérdida de electrones en un sulfuro significa enlaces rotos y esto origina la disolución del sulfuro metálico. Así, se postulan dos mecanismos por el cual se produce la disolución del sulfuro.

Mar 1, 1983

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

By H. J. Marais, P. C. van Aswegen

The Biological Oxidation (BlOX®) Process for the treatment of refractory gold ores was commercialized in 1988. During the last decade, the technology has developed into a mature, commercially viable process, with five additional operations commissioned, including operations at Sao Bento in Brazil, Harbour Lights and Wiluna in Australia, Ashanti in Ghana and Tamboraque in Peru. With ongoing development, the efficiency and cost effectiveness of the process have both improved, making it an attractive alternative to conventional refractory treatment processes such as roasting and pressure oxidation. The bacterial culture is robust and can withstand the normal fluctuations experienced on an operating plant. The plants are simple to operate, making it ideal for remote areas. The scale-up potential of the process has been proven, and it can be applied to large refractory ore bodies. The process is environmentally friendly. Neutralization of plant effluents produces precipitates that comply with the most stringent environmental regulations.

Jan 1, 2000

By James Norman, O. C. Ralston, John Dasher

Most mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chro-mite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficia-tion, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put In the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabrom-ethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. Earlier Work It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the recovery of gold from the mud of a lake

Jan 1, 1943

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988