Search Documents

Geotechnical practice combines the site engineering geological model with engineering design and operations to control risk. The responsibility of the geotechnical professional is to present relevant engineering geological information to an engineer to effectively impact an outcome. Return is enhanced by understanding expected operating and capital cost due to ground conditions.   Risk is effectively communicated by a successful geotechnical practitioner. In a mining environment the need is to assess ground conditions accurately and quickly, and to effectively communicate expected ground response due to mining. A good engineering geological model includes a description of geotechnical engineering parameters to design assuming reasonable expected soil, rock and water conditions. Pit slopes are steepened, stope spans widened and waste foundations and land forms are constructed all under geotechnical control.   The responsibility of the geotechnical professional is to collect, assess and disseminate relative engineering geological information. The geotechnical professional is a person advising on ground related engineering, and generally operates within geology and engineering end members.   Return is better assessed on an understanding of ground cost. In operations the goal is to meet production at lower cost. In evaluation, regional and exploration geology, mine design and expected operational factors influence expected cost and project return. Return allows companies to meet shareholder expectations, attract equity to develop and add value to the community.   This paper presents a discussion with some examples to present an approach and design philosophy for geotechnical practice in the mining industry.

Jan 1, 2004

By G. V. Sullivan, B. E. Davis, T. O. Liewellyn

A technique was devised by the US Bureau of Mines to recover coarse [+1.2-mm (14- mesh)] North Carolina phosphate now discarded as waste. Concentration utilizes the difference in particle sphericity between the relatively flat calcite and the rounded phosphate pebbles. Sizing, treatment in a continuous hydraulic classification system, and grinding upgraded a 17% P,O5 reject to 4.5% P,05 with a phosphate recovery of 63%. The CaO: P2O5 ratio was reduced from 2.49 to 1.66.

Jan 1, 1987

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By N. K. Chen, C. H. Mathewson

Recrystallization of aluminum single crystals after plastic extension is carefully studied in relation to the structure of the deformed matrix. The shapes of the new grains are analyzed with regard to slip planes and to the presence or absence of deformation bands. A mechanism by which the orientations of the grains are related to the parent lattice is described. EXPERIMENTS previously reported&apos; have been extended to develop some of the characteristics of the new crystals which are formed on annealing axially strained crystals whose deformational characteristics had been documented with special care. Thus, the presence of deformation bands affects the growth contours of the crystals, some of the strained crystals produced single crystals anew, and some, polycrystals, on annealing, while others merely "recovered" or "polygonalized" after the 600°C annealing treatment generally adopted in these tests. In the matter of orientational relationships between new crystals and the strained matrix, the present experiments have added little to previous experience, which had demonstrated great variety in the range of orientations encountered and no simple theory or correlation. For example, there has been ample evidence for the predominance in various face-centered cubic metals of a favored orientational relationship; viz., a rotation of 30° to 40° around a <1ll> axis, between grains growing in a matrix with a strong single orientation texture and the matrix itself.&apos;-&apos; This reorientation has been interpreted by various investigators in support of both the "oriented nucleation" and the "oriented growth" hypothesis. In the case of axially extended single crystals of aluminum, no general relationship, such as the one stated above, can be used to correlate the orientations of the recrystallized grains with that of the original crystal. Thus, Carpenter and Elama and Burgers and Basart7 were content to assume that the orientational relationships so developed were random in nature. Mathewson, however, in the Campbell Lecture of 1943 "rgued on the basis of <112> slip that a complex strain, chiefly characterized by rotation around a variable axis in the slip plane combined with a principal rotation around the pole of the slip plane, could be responsible for such devious relationships. Nevertheless, owing to the limited data now available dealing with orientational relationships between new grains and the single crystals strained in tension from which they have recrystallized, no adequate examination of the above generalization could be made. Here, there is the disturbing preliminary condition that any desired orientational relationship may be expressed by means of two rotations about mutually perpendicular axes, so the process lacks a certain critical flavor and any successful choice of axes meeting certain theoretical requirements could be replaced by another differently selected pair. With this reservation clearly in mind the process of double rotations, as previously indicated, was used to relate the orientations of the single crystals which grew out of the strained single crystalline matrix and was construed as certain evidence in favor of the theory of incongruent shearing action proposed by Mathewsons as a necessary element in the (111) slip process with close-packed metals. There is here

Jan 1, 1953

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute, since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1" to 2°C. per min. with or without slow stirring (Fig. I). By this method the lead-rich end of the lead-alltimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the liquidus curve of the binary alloys did not intersect at the euteotic temperature. An equivalent effect mas observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent in- vestigation by Pellini and Rhines,1 who determined the eutectic temperature to be 2 51.5°C. The observation that the curves of primarY crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomeilon by assuming the existence of a compound Sb4pb. He felt that supercooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3 the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature Of 2500 to 252°C. at a rate Of coo1ing of about 6°C. Per min. Abell Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic only 11 .4 to 11.5 per cent antimany. (Previous analyses by Stead4 .in 1891 gave 13 per cent.) Weaver,ll however, reported in 1935 that cooling cunres indi-

Jan 1, 1944

By John Naughton

At the General Electric ResearchLabora-tories, we have been interested in the iron-manganese system and the effect of hydrogen on the properties of these alloys. Dr. H. H. Uhlig previously has presented some of these results.&apos; We wish now to offer some other of the data that have a bearing on the subject of this symposium. In the determination of hydrogen in the iron-manganese system by any heating Method we are presented with the problem of the evaporation of volatile manganese and the consequent adsorption of hydrogen by this evaporated metal. It seems wise. therefore, to extract gas at as low a temperature as feasible. Consequently we chose the vacuum or hot extraction method for the analyses of these alloys. The apparatus used is shown in Fig. I. The design is a modification of the apparatus described by Holm and Thompson. To limit loss of hydrogen, samples are stored in a chamber immersed in liquid air. We recommend this procedure whenever there is a question of loss of hydrogen at room temperature. Thence they are moved to the quartz furnace by means of a small magnet, where they are heated by induction to 700&apos; to 800°C. The extracted gas is removed by the circulating pump and placed in the known volume VI (or V2). The circulating pump has been described.3 It is so designed that in spite of the fact that the outlet portion of the pump is part of the known volume, this volume is affected neither by the speed of pumping nor by the pressure of stored gas. The pump also serves to circulate the gases for analysis. The analytical system consists of a

Jan 1, 1945

By Harold J. Bennett

The purpose of this study was to develop methods for the financial evaluation of mineral deposits. This includes the selection of the best alternative mining and processing methods and production rates. This was done by performing a financial evaluation through computer simulation using sensitivity and probabilistic risk analysis. The criterion used to measure the relative advantages of these investment and operating alternatives is the discounted-cash-flow rate of return. Included is a description of the theory and methods used in the probabilistic analysis approach, which is based on the premise that the expression of a range of values in establishing an estimate for a parameter is more realistic than the choice of a single value. Numerous simulations are made using randomly selected values of the input parameters resulting in a frequency distribution of the rates of return and their relative probability of occurrence. The sensitivity analysis method is described and combined with the probabilistic analysis to interrelate mineral reserves, capital investments, operating costs, and production rates. The ability to vary these input parameters on successive runs has permitted the selection of the best alternative mining and processing methods and production rates for a given mineral deposit. For illustrative purposes the evaluation of a mineral deposit was performed using three alternative mining and processing methods at three different quantities of resources and various production rates and prices. The computer program used in this analysis was written in FORTRAN II for maximum compatability and should run without modification on most computers having BK (8,000-word) core memory, a card reader, and printer (120 characters per line).

Jan 1, 1970

By C. O. Bundranl, Peter Dehlinger, W. H. Browne

Brief laboratory investigations are described which attempt to determine optimum .sand concentrations in gel-sand and oil-sand1 well-treatments. The investigations apply to the case where sand acts as a propping agent in formation fractures. Both analytically and experimentally it is demonstrated that optimum sand concentrations can be defined. It is difficult to translate laboratory results to field treatments, however, since the relative distribution of sand and fluid in fractures may not be the same as injected. This is because fluid may penetrate the furtherest narrow portions of fractures, which would not pass sand. Optimum concentration of a monolayer of Ottawa sand in fractures of 0.025-in. width at the usual range of pressures encountered in treatments appears to be about 95 to 2 lb/gal. of gel. An investigation of abrasion of rock-walls by sand in treatments, described in the Appendix, shows that such abrasion is not probable in significant amounts. INTRODUCTION Experience in the Spraberry formation of West Texas, as well as in other formations, has shown that. sand is a necessary and vital part of gel-sand and oil-sand treatments. Many observers of treatments have also concluded that there seems to be an optimum range of sand concentration for these injections. Brief laboratory investigations were made at Battelle Memorial Institute to study flow in fractures with different sand concen- trations. To investigate the existence and range of optimum concentrations in the laboratory, however, necessitates knowledge of the mechanism by which the sand aids in increasing subsequent production. The action of sand in fractures is usually thought to be either that of a propping agent, thus providing a greater effective formation permeability; that of an abrasive in eroding fill material in fractures; or that of an abrasive eroding rock-wall irregularities along fracture surfaces. Investigations described in the Appendix show that sand does not appear to erode rock-wall materials appreciably. In a subsequent paper it is reasoned, at least for the Spraberry formation of West Texas, that the primary action of sand is not in removing fill materials in fractures. In this formation, and probably others, too, the main effect of sand appears to be that of a propping agent. Both analytical and experimental investigations were made for the case of a monolayer of sand acting as a propper, in which sand concentrations were determined that would, after treatment, permit flow of the maximum quantities of oil from the formation into a well. If too few sand grains are injected into fractures in which the bottom hole pressure has decreased appreciably below the original formation pressure, the confining pressure in the formation may become relatively large, thus compress the rock-walls around the sand grains, essentially close fractures, and so decrease the subsequent flow of oil. Similarly, if too much sand is used, the flow of oil will he impeded by the volume of sand present. THEORY Although an analytical approach to determining optimum sand concentrations involves gross assumptions.

Jan 1, 1955

By C. E. Lawall, C. T. Holland

When this study was started very little information was available regarding the physical characteristics of West Virginia coals. This was particularly true of friability and of crushing strengths of the coals. Some work had been done on specific gravity studies but the available information applied to only a few coals. In practically all coal-classification systems thus far proposed, the predominating factors of classifications are largely based on the chemical characteristics of the coal. Recently some investigators have pointed out that a classification based on chemical and physical properties of coal might serve to place coals in their proper group better than classification systems based on chemical properties alone. One of the aims of this study was to obtain some data on the physical properties of coal which might help to classify West Virginia coals. The Samples Fig. I shows where the coal samples were obtained and the approximate division line of the high and low-volatile coal fields of the state. The relative geological horizons of the coal beds tested are shown in Fig. 2. In securing samples of coal for friability and specific gravity tests, it was the aim always to obtain a representative sample of lump coal produced at a particular mine. The samples were obtained from the loading boom, the railroad car, or the mine cars. Wherever it was possible to secure samples from a loading boom they were taken from it by taking shovelfuls of coal from the loading boom every minute until about 200 lb. of coal was obtained. If there were no loading booms used at the mines sampled, the coal sample was taken from a loaded railroad car by systematically taking shovelfuls of coal at definite intervals over the whole top of the car until about 200 Ib. of coal was obtained.

Jan 1, 1932

By J. W. Halley, T. S. Washburn

RIMMING steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard, 1, 2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel.. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By Donald R. Reichmuth

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker&apos;s "Annotated Tables of Strength and Elastic Properties of Rocks."1 There are now three distinct approaches being used to determine the tensile strength of brittle materials. These are shown schematically in Fig. 1. The first method consists of simply pulling the specimen apart by applying an axial load. Although this procedure is the easiest to understand, the technical problems encountered during testing are numerous. Specimens cannot be readily fabricated into dumbbell-shaped specimen* like those customarily used for testing inetals. Cylindrical specimens cannot be loaded in jaw-clamps because adverse stress conditions arise at the clamping points, which causes unreliable results. An innovation developed by Niles Grosvenor at the Colorado School of Mines, in which the load is applied through steel-end caps glued to the ends of the specimens, has considerable merit, hut the samples are costly to prepare.2 All tests using a direct pull are further handicapped by the possibility of small amounts of bending being present, the specimen&apos;s surface condition, and

Jan 1, 1968

By Don Eby

The application of electric arc furnace smelting of lead, antimony, and tin bearing slag from a reverberatory furnace will be discussed. The selection procedure for the 4.0 MVA electric arc furnace in Indianapolis, Indiana is presented. The design criteria for the transformer, electrodes, refractories and associated equipment is presented. The operation of the furnace including chaJ:9ing, bullion tapping, slag tapping, ventilation, slag composition, metal recoveries, and toxic leach results of thra.1 away slag are discussed. Flow charts and the equipment specifications are given.

Jan 1, 1990

By I. de Jong, G. Van Weert

Silver cyanide adsorbs extremely well on activated carbons. This suggests that the addition of soluble silver salts to trace cyanide containing waste streams should allow efficient cyanide removal with active carbon. Silver losses, however, would make this method expensive and also objectionable, since silver has biocidal effects. When silver impregnated carbon is used, these problems are overcome. Test work has shown that such silver remains on or in the active carbon, that cyanide concentrations can be reduced to the level of detection (< 5 ppb) and that the silver impregnated carbon can be reactivated with equipment similar to that now in use at gold milling operations. Initial results on the type of carbon, the impregnation procedure and the level of silver, and the effect of repeated regeneration are discussed.

Jan 1, 1992

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually aver- age about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment.

Jan 9, 1953

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

By Carlos C. Hidalgo

El presente trabajo señala los cambios realizados en el procedimiento de completamiento de los pozos petroleros desde 1958 y evalúa los efectos de las nuevas técnicas introducidas en el sistema petrolero. Para ello, se revisa la historia de la producción de las cuatro áreas que tienen suficientes pozos para comparar lo métodos antiguos y nuevos de completamiento. Asimismo se realiza un análisis de los costos de completamiento para los mismos pozos que fueron considerados en la comparación de productividades. De la comparación establecida entre los métodos antiguos y los nuevos procedimientos, se encontró que el nuevo estilo conduce a recuperaciones totales más altas a un costo menor. El otro beneficio estriba en un mejor control de entradas de agua o gas y una mejor adaptación futura de los pozos a posible inyección de agua o a cualquier otro proyecto de recuperación secundaria.

Jul 20, 1961

By Lillian Erskine

WHILE brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades&apos; records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder&apos;s employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders&apos; ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 2, 1919

By Edward Keller

About a dozen years ago the art of bessemerizing copper- * matte, brought to these shores from France, was first established at the smelter, in Butte, Montana, of the Parrot Silver and Copper Company, which had bought the process from Mr. Manhks, the inventor. Through the efforts of Mr. J. E. Gaylord, general manager, and Mr. A. J. Schumacher, snperintendent,, assisted by an able staff, the new method rapidly underwent, at the Parrot establishment, an evolution towards higher perfedion, and within a few years its success and its advantages were so marked that all the great works in the west followed in the footsteps of this pioneer. The converter-process has now practically superseded the reverberatory-process in this country. The latter will undoubtedly, in a not very distant future, be relegated to metallurgical history. The writer has availed himself of what was perhaps the last chance to make comparisons of the two methods, working practically on the same material on an extensive scale, the reverberatory process being that of the Baltimore Copper Smelting and Rolling Company,* while the converter-process is that of the Anaconda Copper Company—both using the matte from the latter company&apos;s works in Anaconda, Montana. For the greater portion of the material considered in this paper, the writer is indebted to the two companies. In order to understand the difference of behavior of the several elements, and the difference of the copper produced in the two processes, it is best to study and follow those elements

Jan 1, 1899

By James J. Norton, Lincoln R. Page

Effective methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War II, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals are unsystematic in their occurrence in pegmatites. Pegmatites have been de- scribed as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed," "irregularly disseminated,&apos;&apos; of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in size and distribution of the essential minerals, and variety and proportion of the accessory minerals, and "spotty."

Apr 1, 1956