Search Documents

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

The mobility of radionuclides released into aquatic, terrestrial and subsurface environments by mining, industrial processes is an area that deserves significant scientific attention. The presence of microorganisms in these environments can influence the transport of radionuclides. Free-living microorganisms constitute mobile suspended particles that may have a radionuclide sorbing capacity higher than that of the environment. Radionuclide transport will then proceed faster with than without microorganisms. In contrast, if the majority of the microorganisms are growing in biofilms on surfaces, transport of radionuclides may be reduced. Microorganisms can directly sorb radionuclides either within the cell structure or on the cell wall. Radionuclides could also be sorbed by minerals precipitated by microorganisms. Microorganisms produce complexing agents that can influence radionuclide mobility. The involvement of microorganisms in biogeochemical processes is related to their ability to include various chemical elements and their combinations into biochemical redox reactions. Microorganisms can alter the extent of radionuclide oxidation that results in their deposition as a result of the formation of insoluble forms. Some studies have shown the bioremediative potential of stimulating reducing bacteria to use some of the soluble radionuclides as electron acceptors and thus precipitate them out of solution. The microbial involvement in providing a barrier for radioactive element migration (uranium, technetium) and the formation of ores (eg uranium) has been justified. The mediated impact of microbial activity on radionuclide migration occurs through its effect on the ambient geochemistry by geochemical speciation changes, pH changes and changes to the ambient redox potential. As the mobility of many radionuclides depends on the pH and redox potential of the environment, these microbially mediated geochemical changes can influence radionuclide migration through changes to both the dominant radionuclide species and mineral phases.

Jan 1, 2004

Establishment of a Bureau of Mineral Research at the Michigan College of Mining and Technology, initiated by the State of Michigan with legislation in 1951, is moving toward realization. The Michigan Legislature appropriated $24,000 to cover preliminary costs of plans and specifications for "engaging in a broad, widespread study of the beneficiation of lowgrade ores, of ore dressing, and all the problems of metallurgy that enter into such a program." Ralph C. Calder, of Detroit, who designed Michigan Tech's campus buildings, is preparing plans for the proposed Ores Research Building. Members of the college staff, Professors F. J. Tolonen, W. E. Keck, and Research Engineer Paul Jasberg are assisting in preliminary planning. C. Harry Benedict, retired chief metallurgist of Calumet and Hecla and a member of Michigan Tech's Board of Control, is assisting with technical details. Professor Nicholas Manderfield, head of the department of Mineral Dressing, was assigned to visit other research installations and suggest plans for the Bureau.

Jan 1, 1952

By E. C. Kersey, R. J. Gennone

MetALLOGRAPHIC investigations of composites of zinc alloys and aluminum have been made to study the effects of various thermal treatments on the zinc-alloy grain size and diffusion of zinc into the core material. The use of various alloys of zinc has necessitated the development of a universal etchant which will allow microscopic examination of the zinc grain size regardless of the composition.

Jan 1, 1960

By William A. Beck

Bauxite was discovered in the Springvale district in 1916. About 16, 000 tons was mined in the period 1916 to 1922, but no bauxite mining has been done since that time. The Bureau of Mines explored for bauxite in the district from September 5 to November 18, 1943. During the life of the project, the Bureau of Mines obtained mineral exploration agreements covering a total of 11,330 acres from 50 property owners. A total of 388 holes were drilled on five of these properties and 164 samples were taken and analyzed. The Springvale bauxite district includes an area of about 30 square miles in the northwestern part of Randolph County, Ga. The village of Springvale is in the west central part of the district, and Cuthbert is 8 miles southeast of it (fig. 1).

Jan 1, 1949

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By Armando Valenzuela

Arsenic has been a common impurity in copper sulfide concentrates treated pyrometallurgically in Chile, which inevitably during the smelting-converting process reports in the final copper product affecting its properties, but also affecting environment as a very toxic occupational hazard. The enforcement of air quality standards, which regulate pollutants such as sulfur dioxide, particulate matter, and arsenic, has resulted in the implementation of pollution abatement plans and emission reduction schedules mainly by state-owned copper concentrate smelters. Investments associated with these plans incorporated gas-handling systems in order to capture polluting emissions. Electrostatic precipitators recover dusts containing mainly Cu and As which are leached to recover copper, while arsenic is disposed currently in the form of ferric arsenate. Gases containing high sulfur dioxide content are treated in plants to produce sulfuric acid, which is used in various classical and new hydrometallurgical processes. Additionally, smelters have effluents treatment plants for arsenic disposal either as ferric arsenate or calcium arsenate/arsenite. This paper reviews the environmental situation of the Chilean metallurgical industry, and the present trends for arsenic management are particularly emphasized since Chile is the world?s largest copper producer.

Jan 1, 2006

By W. G. Kegel

The past few years have produced a rash of demands for changes in America's way of doing things. From manufacturer to consumer, the rules have been changed. Some of the demands were needed and, when legislated to requirements, did manage some good for all concerned. Other demands made by zealots and taken up by regulatory agencies have forced costly changes on our way of life. No segment of industry has been exposed to more new rules and regulations than the deep coal mining industry in the United States. There is no denying that some good has evolved, but most mining men know that the effects have done more to reduce production and increase cost than they were ever intended to do.

Jan 1, 1975

By C. M. Nickerson

The possibility of deeper production in the Buena Vista Hills was first considered in 1933. At that time, however, the heavy state curtailment program served to deter any operator from drilling test wells, which, if successful, might upset the proration schedules. Because most of the acreage was held by several major operators and the remainder by substantial independents, the adoption of a plan of cooperative development was considered desirable. Such a plan was formulated for the development of any deeper oil and gas horizons that may be found to exist. This plan, which was signed by the Secretaries of the Navy and of the Interior on behalf of the United States on July 9,1936, is now effective for the development of lands within the area shown on Fig. 1. Unlike most unit plans, the present cooperative development plan permits each operator to drill and produce his own wells. For the purpose of this plan the Buena Vista Hills field is divided into two pools. The present production is classed as the " old pool,"' while any future production below a certain marker which roughly coincides with the bottom of the Santa Margarita formation is included in the "pool" to which the provisions particularly apply. Naval Petroleum Reserve No. 2 lies within the area and constitutes the major portion of the Federal leases subject to the plan. There are 39,040 acres and 27 operators within the area. Twenty-six operators controlling 99.5 per cent of the acreage have signed the agreement. Geology oF the Buena Vista Hills The Buena Vista Hills consist of a low range in the southern portion of the San Joaquin Valley, and are roughly parallel to the adjacent Temblor range to the south. The Elk Hills oil field parallels the Buena Vista Hills a few miles to the north. The subsurface structure is a re-entrant anticline upon the major Midway-Sunset monocline. This anticline is divided into two minor

Jan 1, 1937

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By G. J. Govett

THE RESERVES of industrial minerals of the Western Plains are probably several times more valunable than all the known deposits of metallic minerals of the Canadian Shield, though sharing little of the latter's popular appeal. Because of comparatively low value per unit weight or volume, an adequate and accessible supply of industrial minerals is essential for the full development of any territory; assessment of the value of deposits should consider fully the proximity to cheap transportation, and existing and potential markets. Production statistics of industrial minerals are probably a more reliable guide to economic development than, for example, those of petroleum, and the relative importance of industrial minerals increases with growth of the population. The development of a high-volume natural deposit such as petroleum naturally favours an increase in population, and thus industrial minerals form an integral part of an expanding industrial economy. This situation is clearly demonstrated by the relationsl1ips of industrial minerals production, petroleum production, and population growth, in Alberta (Figure 1).

Jan 1, 1959

By J. H. Frye, S. G. Holder, E. E. Stansbury

Internal friction studies on annealed and cold-worked pure silver and alloys of silver with 4.5 atomic pct each of Cd, Sn, and Sb are reported. Small amounts of cold work, introduced by stretching pure silver, decrease the internal friction; large amounts of cold work, by wire drawing, cause this decreased internal friction to rise. Results of severol anneoling histories on the room-temperature in-ternal friction indicate a rather complex recovery and recrystallization behavior. A rather system-atic alloy effect is observed for the elements of Period V-B in silver in both the annealed and cold-worked states. DURING recent years internal friction measurements at very small stress levels have been interpreted in terms of structural models and mechanisms occurring within the metal or alloy.These measurements have been made over wide ranges of frequency of vibration and of temperature. While the effects of impurities, alloying, and plastic deformation have been studied by numerous investigators, no investigations of the effect of a series of solutes related by their position in the Periodic Table on a given solvent seem to have been reported. The present paper reports internal friction measurements on silver and on certain silver-base solid solutions to determine the values of room-temperature internal friction associated with varying amounts of plastic deformation and after different annealing

Jan 1, 1957

By K. J. Richards, W. J. Schlitt

A combination of industrial and laboratory data is used to explain the interrelationships between operating parameters and cementation plant performance as measured by copper recovery and iron consumption. The chemical factors considered are the relative concentrations of copper and ferric ions in solution, acid concentration, the possible buffering action of other dissolved salts and solution temperature. The effects of flow conditions, solution oxidation, the presence of metallic copper and retention time are also considered. Based on the various relationships developed, possibilities for plant optimization are discussed.

Jan 1, 1974

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining com­munity about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

Jan 1, 2008

By K. Norrena, E. Magri

An important problem in mine operations is the classification of material as waste, low-grade stockpile and ore. This classification must often be made with blasthole data that are widely spaced and that have sampling errors. Geostatistical-simulation techniques combined with basic economic principles allow a procedure for classification that maximizes the expected profit. Geostatistical-simulation methods (Gaussian, indicator or annealing-based) allow the integration of hard and soft data in the creation of alternative, equally probable realizations of the mineral grades. At each location, for each realization one calculates the "profit" if the block were to be classified as ore or waste. The optimal classification is the one that maximizes expected profit (a maximum profit selec¬tion or MPS procedure). In this paper, the authors discuss the theoretical justification of the method and implementation details. The use of blasthole data from different types of mineral deposits, that is, different levels of continuity, are considered. The authors also show the efficacy of the procedure with different levels of sampling error. The increased revenue due to the MPS procedure and improved sampling is shown. The paper shows the geostatistical-simulation procedure and the uncertainty in block grades that result from incomplete and imperfect sampling. The optimal classification is presented. Optimal block classifications are transferred to realizable dig limits by hand-drawing polygonal boundaries. The results of the proposed method are compared to classification based on kriging. Limitations and areas of future work are identified.

Jan 1, 2000

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Wm de L. Benedict Robert Bentley Andrew A Blair Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1941

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some' grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By H. McSorley

"I note that many of you are involved in the production of zinc, lead and copper concentrates and metal, which I am the most familiar with among the non-ferrous metals. This afternoon, I will describe briefly the responsibilities of a commercial manager within a mining/metallurgical company, the basic framework of a non-ferrous metals concentrate agreement and lastly, a brief discussion of the copper, zinc and lead concentrate and metal markets.I hope this talk will contribute to a better understanding of the business between all of us and look forward to a discussion after the presentation.First of all, I work for Noranda Sales, which is the marketing and sales agent for Noranda Minerals' three operating units: Noranda Copper, Noranda Zinc and Mining Corporation. In addition, Noranda Sales acts for other mining companies in the marketing of their raw materials and metals. Noranda Sales is responsible for procuring all raw materials for Noranda's metallurgical plants, such as the Copper Group's Forne and Gaspe smelters, as well as the sale of surplus concentrates and by-products and metal products. In addition, Noranda Sales trades metals and concentrates and owns a metal brokerage business, Rudolf Wolff, a founding member of the London Metal Exchange. It does $3 billion of business in 60 countries, exporting some 80% of Noranda Minerals' output to the world.What are the responsibilities of commercial management in resource marketing to the mine and metal producers?Resource marketing and commercial administration involves assistance in establishing exploration priorities, contributing to feasibility studies, pre-production planning, product promotion and realization of income for many properties and metallurgical plants through completion of supply and sale agreements with other companie"

Jan 1, 1988

By L. R. Stoiser

The mineral resource potential of the Los Bronces deposit was successfully evaluated by an intense, coordinated field program over a 37-month period (April 1978 - May 1981). This project was part of a much larger study to determine the economic feasibility of expanding the open-pit, mine-mill operation 10-fold to 80 kt/d (88,000 stpd). The resource project included more than 120 km (74 miles) of core drilling and 64 km (40 miles) of drill rig access way construction under adverse topographic and climatic conditions, detailed geological mapping, and other related activities. The Los Bronces deposit is composed of an earlier mineralized porphyry-type body intruded in part by a large complex of mineralized hydrothermal breccia pipes. The mineralization is hosted by intrusive and extrusive igneous rocks. Various stages of erosion, oxidation, leaching, and supergene enrichment of copper are present. Drill hole indicated geologic reserves are estimated at 1.3 Gt (1.4 billion st), averaging 0.81% copper and 0.016% molybdenum at a cutoff grade of 0.6% copper equivalence decreasing to 0.25% over the life of the mine. Trace amounts of silver are also present.

Jan 1, 1987

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited. The mine is targeting Zero Lost Time Accidents as a goal.   The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (i.e. underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995