Search Documents

By C. W. Tomlinson

The analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates1 of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineral-ogical constitution of aggregates upon the properties of the concrete and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting is of course dependent upon the experience and carefulness of the analyst. After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed from 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reasonable limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hun- dredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 1, 1916

By George Norman

A NUMBER of methods have been developed for the determination of the dust concentration in air, some of which have been reported as very efficient and for research may be more satisfactory than the method about to be described. In practical mine use, however, the accurate research equipment is unwieldy and requires a high degree of technical skill to manipulate it. Also, it gives less general practical information to the operator in the same length of time than the method described here. Moreover, it is doubtful whether at the present stage of affairs the results obtained from the precise methods have any more practical significance than those obtained with simpler and more portable appara-tus, which can rapidly give a sufficiently reliable indication of the rela-tive dust hazard.

Jan 1, 1937

THE reduction of iron from the ferric to the ferrous state prior to its titration by permanganate or dichromate may give erroneous results in the presence of other reducible metals such as titanium. Stannous chloride and metallic zinc both reduce tetravalent titanium to a lower form, and so increase the consumption of the oxidizing standard: solution. Sulphuretted hydrogen and sulphurous acid do not reduce titanium, but are slow in action and troublesome to manipulate.Sulphuretted hydrogen is considered to be the best reducing agent for iron in the presence of titanium.* In the method to be described the advantages of the H 2S reduction are retained without the disadvantages of using the gas. The reduction is carried out by the action of a metallic sulphide having a solubility product of such a value that the sulphide iom, are utilized as fast as they are formed, and but little free sulphuretted hydrogen is given off.Cadmium sulphide was the first to be tried, but its solubility product (3.6 x 10 - 2~)t was apparently too low. The reduction was satisfactory, but the excess was very difficult to remove. Zinc sulphide (S.P. = 1.2 x 10 - 23) was found to be quite satisfactoryin both respects. The zinc sulphide is preferably used in the form of an emulsion prepared from pure zinc sulphate as follows: About 100 grm. of ZnS047H20 is dissolved in 2 litres of water. H2S is passed until no further precipitate is obtained, the acid formed being barely neutralized from time to time by the addition of ammonia. The precipitation of the sulphide in a slightly acid solution gives a finer emulsion than that prepared in an alkaline solution, and any iron present remains dissolved. The precipitate is allowed to settle and the clear liquid decanted. The precipitate is then shaken up with more water, acidified with a little sulphuric acid, allowed to...

Jan 1, 1922

By V. Panchanathan

The rapidly solidified Nd-Fe-B powders form the entire basis of the bonded magnet industry At present the rapid solidification is carried out exclusively by melt spinning, producing flake like particles having highly stable and magnetically hard microstructure These particles are comminuted into powder before being processed into bonded magnets These powders are magnetically isotropic having coercivities from 4 to 16 kOe The other type of powder recently introduced for bonded magnets is the anisotropic powder made by the hydrogen decomposition desorption recombination (HDDR) process. The characteristics and application of these isotropic and anisotropic powders are discussed.

Jan 1, 1997

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By Richard H. Jahns

Terminology and Basic Specifications Minerals and closely allied natural substances that are used for personal adornment, as raw stock for the fashioning of ornamental objects, or for other decorative purposes can be referred to collectively as gem materials. Industrial gem materials are those employed directly in various areas of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconstant, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Although many building and monumental stones are undeniably ornamental in their uses, treatment of such material is beyond the scope of this chapter. Substances that lose their identity in use are excluded from the gem category. Thus a transparent crystal of beryl would not be classed as a gem stone if it were treated as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means of distinguishing different gem materials on the basis of their recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquois, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of intrinsic properties, and at the present time all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semiprecious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance desirable characteristics that are present initially. The worth of most synthetic gem stones is founded upon the identity between their major properties and the natural characteristics of the corresponding minerals, just as the pleasing qualities of imitation stones depend upon how well certain of their properties simulate those of more valuable substances. The most important specifications of gem materials represent four basic factors: beauty, durability, rarity, and portability. Beauty, whether expressed as splendor, "purity," attractiveness, or in some other way, is mainly a function of personal response to optical properties such as color, transparency, indices of refraction, and dispersion. Freedom from visible imperfections is important for transparent stones. For some substances beauty depends also upon asterism, opalescence, textural and

Jan 1, 1960

By E. P. Haqyes, J. K. Butler

011, and gas development has continued unabated on the Texas Gulf Coast during 1937. Although the number of important new discoveries has not been great, the extensions in older fields, owing to discovery of new sands and the lateral extension of known sands, has been extensive. Twenty-four new producing fields were added during the year, and many of these areas give promise of developing into important producing districts in the future. Alta Mesa, Amelia, Aransas, Clara Driscoll, Five Corners, Hamman, Heyser, Old Ocean, Premont, Seabreeae, Segno and West Columbia have all had major extensions during 1937. The 1937 production for the Texas Gulf Coast was 120,141,429 bbl., or 32f per cent increase over the 1936 production of 90,865,293 bb1. t The total number of producing wells has increased from 6727 to 8968. Well abandonments have becn few and indications are that they will continue to be so. Rigid proration has been and continues to be in effect, and, as a result, wells in the Gulf Coast will have prolonged life. New Fields Tables 1 and 2 contain general information on all fields in this district. The following named fields were discovered in 1937: Aransas County.—Barnsdall Oil Company's No. 1-A Edwards was the discovery well for the Lamar field. It was drilled to a total depth of 9785 ft., plugged back and completed at 7530 ft. in the Frio as a gas and distillate well. Present indications are not very promising for a major field. Bee County.—The McMurray (Strauch) field was discovered by Dirks Bros. No. 1 Strauch at a total depth of 4577 ft. This is a Yegua producer, and had an initial production of 230 bbl. on a 3/16-in. choke. Brazoria County.—The Sandy Point field was discovered by Henry DeArmanls No. 1 Fite, which was completed as a producer at 6501 ft. in the Marginulina-Frio series. Galveston County.—Although the Hitchcock field was discovered in 1936, the first commercial oil producer was completed in 1937 when

Jan 1, 1938

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By Juan Carlos Ramírez

En los últimos años se desarrollaron sistemas para la generación de paredes finales en yacimientos de cielo abierto y así proveer la pared adecuada a los parámetros que alimentan el sistema. Por tal motivo, el objeto del texto es realizar un estudio comparativo entre los dos sistemas de generación de paredes finales: Pushbacks y Whittle 3D. La aplicación de ambos sistemas se ejecutó a través de dos etapas en la mina Cuajone donde el sistema Pushbacks guió el diseño de paredes finales de mina desde 1984 hasta 1989. Mientras que el segundo, se utilizó desde 1989 hasta la actualidad puesto que es un sistema optimizador computarizado que permite obtener paredes finales óptimas en yacimientos explotables a cielo abierto de forma segura.

Apr 1, 1991

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By F. M. Doyle, Jun Li, Milton E. Wadsworth, Ximeng Zhu, E. Peters

The electrochemical behavior of pyrite in borate/sulfate solutions was investigated using cyclic voltammetry. Three anodic peaks at approximately -0.8 V, -0.1 V and +0.5 V (SCE) were detected along with their corresponding reduction peaks. The first two peaks correspond to the oxidation of surface products. The third peak corresponds to the direct oxidation of pyrite with reaction products FeO oxides. sulfate ion and partially oxidized sulfur intermediates present as a surface film of polysulfides and So. The Few oxides and sulfur intermediates were reduced to ferrous hydroxide and HS during the negative-going scan. The HS interacted preferentially with Fe(OH), on the surface to form FeS. Excess fenous hydroxide continued to reduce to metallic iron. During the return positive-going scan, metallic iron was oxidized to ferrous hydroxide and FeS was oxidized to pyrite. These reactions are characterized by a unique double peak observed in the region -0.8 to -0.65 V. The growth kinetics of the surface sulfur film formed during anodic oxidation were studied using chronoarnperomeay. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. The reaction rates were affected by applied potential, solution pH and temperature, but were independent of electrode rotation speed. A reaction kinetics model which fitted well with experimental results, was developed.

Jan 1, 1993

By A. T. Miesch

The purpose of this paper is to explore relations between the distribution and composition of uranium deposits on the Colorado Plateau and mineralogic, chemical, and lithologic aspects of their host rocks. The paper also appraises the host-rock sandstones as possible sources of elements in the uranium deposits. Other possible sources of elements are not discussed. Uranium deposits on the Colorado Plateau consist largely of sandstone and small amounts of mud-stone impregnated with uranium and vanadium miner- als and a suite of minor accessory minerals containing copper, lead, zinc, silver, iron, cobalt, nickel, yttrium, molybdenum, selenium, and arsenic, in addition to other elements locally. The deposits consist of clusters of closely spaced ore bodies which commonly aggregate several thousand tons, but range in size from less than one ton to several million tons. With only rare exception, the deposits show no close relation to fractures. The ore bodies are generally tabular in layers nearly parallel to the bedding in the host rocks, or they cross bedding at large angles to form roll structures. Absence of fracture control necessitates that the ore and associated elements were transported to the deposits by way of interstitial pore spaces in the sandstones. This points to the general process of lateral secretion as a possible mechanism of ore formation, and suggests the host-rock sandstones as a possible source of the metals. Roll structures in the ore

Jan 1, 1962

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920's because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By Badiozamani Khosrow

Introduction The mining industry has been using computers since the late 1950s. Despite this early start, the use of mine planning software is not a common practice in many operations. But the trend might be changing because of the availability of relatively inexpensive personal computers (PC). The introduction of these machines has generated unprecedented interest by mine managers to computerize their planning operations. However, some managers have become disappointed with the PC's lack of adequate software and the inability to handle the massive amounts of information required for modeling. This paper is an attempt to shed some light on the future of computers in the mining industry. It will examine: • historical progress in the computer industry, • future advances in the computer industry, • historical usage of computers in mining, and • future alternatives available to mining. Historical Progress The computer industry has come a long way since the first full-fledged electronic digital computer Electronic Numerical Integrator And Calculator (ENIAC) was built in 1946. This machine weighed more than 27 t (30 st). It contained 19,000 vacuum tubes, occupied 139 m2 (1500 sq ft), and could perform 5000 additions per second. By contrast, today's fastest, commercially available computer is the CRAY-X. It weighs less than 5 t (6 st), has no vacuum tubes, occupies less than 9 m2 (100 sq ft), and performs over 100 million operations per second. This is an incredible advancement in less than 40 years. One person commented on the rate of advancement in the computer industry. He suggested that if the auto industry had advanced at the same rate as the electronics industry, we could buy a Rolls Royce for $2.75 and it would run

Jan 9, 1984

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever' and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968