Search Documents

By Harvey Cline, Donald P. Ferriss

THE violent outgassing of commercial tungsten and other refractory metals when melted in an electron beam zone refining apparatus1"3 is dealt with experimentally by one or both of two approaches. One is to provide a suitable emission current control1,2 the other is to purify the metal in the solid state before melting.4 The first of these is usually sufficient, but the authors chose also to investigate the source of the troublesome gases and to devise means of solid-state purification. Some further insights into the use of tungsten as a structural material at temperatures near its melting point were also revealed in the course of the work. One may speculate on the causes of gas formation in tungsten at high temperature by inferences from the literature and an examination of the impurities in commercial wire. Davenport5 observed microporosity in both tungsten and molybdenum filaments heated to several hundred degrees below their melting points. Studying the function of oxygen in molybdenum welds, Perry, Spacil, and wulff8 attributed similar porosity to the disproportionation of Moo2 to molybdenum metal and Moo3. Tungsten dioxide also disproportionates7 above 2000oC to yield WO3 vapor at considerable pressure. Commercial tungsten contains some 5 to 20 wt ppm O and a similar concentration of carbon depending on the details and precautions of processing. Therefore, evolution of CO is also a strong possibility as a source of gas at high temperatures. Furthermore, even for activities in the order of 0.01, it may be calculated that the pressure of CO at 3000°C would be over 4000 psi, which is in excess of the tensile strength of tungsten at this temperature.9,10 Powder metallurgy tungsten contains some 0.02 pet Fe and 0.002 to 0.005 pet of the elements Ni, Si, Al, Ca, Mn, Mg, and Mo; at temperatures over 2800°c, therefore, these elements will exhibit appreciable vapor pressure, though small compared to that of WO3 and CO. Some of these impurities may react to form high-pressure monoxides such as SiO and A10. Finally, dissolved and occluded nitrogen is an ever-present source of high-pressure gas. Commercial Type 218, General Electric filament wires, 0.025 in. diam, were heated by resistance in 10 -4 mm of Hg and in argon or hydrogen at pressures from 50 µ to atmospheric. For temperature determinations in vacuo, the Jones - Langmuir8 current-temperature relationship was employed. For gaseous atmospheres, the burn-out temperature was assumed to be the same as in vacuo so that a small, constant correction could be made for temperatures below burn-out conditions (i.e., local heating to failure). Several dozen experiments may be summarized by pointing out some structural observations. At 3050oC in 1 atm of A, porosity is very evident after 30 min, as shown in Fig. 1. For the section in Fig. 2, failure occurred 200°C below the melting point and many voids have grown in the grain bound-

Jan 1, 1962

By Charles MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now "potash" has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks.

Jan 2, 1915

By D. T. Goettge, E. L. Robinson

The phase changes occurring in low carbon steel during hot strip mill rolling are shown to be metallurgically significant when related to commonly used temperature control points, particularly finishing and coiling temperatures. In combination, these temperatures are shown to have an important influence on the level and uniformity of hardness, grain size, and carbide characteristics of the finished hot and cold rolled sheets. PRODUCTION of wide flat-rolled products ordinarily requires a number of operations in sequence to prepare the material for shipment to the customer. Most products are tailor-made for specific end uses, with each operation contributing certain properties to the finished material. Since the characteristics imparted to the semifinished product by a given step in processing carry through to the finished product in varying degrees, it is important that the intermediate stages of production of flat-rolled strip be carried out with the same care which characterizes the last or finishing operations. The step of hot strip mill rolling is common to the production of all of the various types of flat-rolled product; therefore, the hot strip rolling is an especially important point at which to recognize and control those variables which have an effect on the surface characteristics and metallurgical properties of the finished product and which influence the ease of conducting subsequent operations. Orders entered at a producing mill usually show an end use or describe an article or part into which the ordered product is to be fabricated. Applying his experience as to the properties necessary in a finished sheet to suit the end use and to perform successfully in the fabrication involved, the metallurgist selects a steel of suitable composition and deoxidation practice, and slabs of appropriate dimensions are produced for rolling on the hot strip mill. At this stage of processing, the metallurgist faces the problem of controlling hot strip mill practice in the light of his diagnosis of the properties necessary to meet the end use, paying due attention to the accompanying problem of producing a strip which can meet processing requirements on subsequent units in the mill. It is the purpose of this paper to describe some of the factors which he must consider in solving these problems and to indicate some of the principles which guide him. Equipment, Physical Requirements of the Strip, and Temperature Measurement The metallurgist must, of course, be familiar with the physical layout of the mill, the temperature-measuring equipment available, and the physical requirements of the hot strip product before he can apply his metallurgical knowledge to the problem; hence, the first section will consist of a brief discussion of these matters. The usual hot strip mill consists of reheating furnaces, five or six roughing stands including a scale-breaker, holding table, and second scalebreaker, six-stand finishing mill, runout table with spray cooling facilities, and coilers. A schematic diagram of a typical layout is shown in Fig. 1. Slab temperatures are primarily a function of heating time and furnace temperatures, while mill speeds, spray practice, drafting practice, available water pressure, temperature of the cooling water, cross sectional dimensions of the strip, coil size, and equipment limitations, either singly or in combination, determine what rolling temperatures are practical on a given hot strip mill unit. Thus, it is possible that a set of temperatures which can be utilized successfully on one mill cannot be used on another. However, adjustments in temperatures and rolling practice can usually be made to develop the desired metallurgical properties. In addition to the metallurgical properties developed through proper temperature control, the hot strip mill must also provide strip with certain physical attributes which may be summarized as follows: Strip Cross Section—The strip contour should conform to a section which will give the best results in the cold reduction operation. This is generally recognized as a strip with 0.001 to 0.003 in. crown or shoulder-to-shoulder convexity depending on width, and freedom from concave, flat, or wedge-shaped cross sections which cause metal buildup in cold reduction. Excessive drop off in thickness at the edges can also be very detrimental in cold reducing to light gages. Gage, Width, and Camber—All of these must be controlled. For example, rundown or increasing thickness from the front to the back of the coil results in nonuniformity in the thickness of hot-rolled sheet product and in added difficulty with gage and welds in cold reduction. Similarly, excessive width variation is the cause of guide trouble and excessive edge scrap at later stages of processing, while excessive camber is the source of a variety of processing troubles. Type of Oxide—Product intended for pickling should have a predominance of the type of oxide most easily removable in sulfuric acid. It is generally recognized that this type is obtained by use of maximum table cooling water and cold coiling

Jan 1, 1957

By W. C. Hagel, H. J. Beattie

Variations in the secondary phase reactions of six nickel-and cobalt-base alloys were determined as a function of solu-tioning from 1700" to 2200°F and aging at 1200" to 1800° F for times up to 1000 hr. Room-temperature impact energies and hardnesses were also measured. Precipitation hardening of these alloys results mainly from the grain-interior formation of ? '; M23C6 appears principally as grazn-boundary cells which can be eliminated by intermediate high-temperature aging treatments. Cellular precipitation of ?' occurs up to 1500°F in cobalt-nickel alloys devoid of chromium, where precipitation by this mode can be attributed to a large degree of lattice disvegistery. THE usefulness of nickel- and cobalt-base alloys is dependent on balancing the strength and ductility provided by the solid-solution matrix, dislocation-type subboundaries, grain-boundary phases and genera1 precipitation within individual grains. Since equilibrium relationships for complex austenitic alloys are not easily fixed, a satisfactory balance

Jan 1, 1960

In accordance with the requirements of By-Law LX,- I beg leave to submit herewith the report of the Library Committee for the year 1916. The activities shown by the sale of the Institute's publications during the year are somewhat larger than last year, due principally to the increased sale of special editions on account of the larger sale of the Posepny and Emmons Volumes, owing to increased advertising and to the reduction in price of the Emmons Volume. The sales were distributed as follows: Sale of Transactions $3,237.07 Sale of Special Editions 1,722.50 Sale of Bulletins and Pamphlets 2,263.95 Total $7,223.52, The Institute library has now been merged with the libraries of the. other three Founder Societies and is known and administered as the Library of the United - Engineering Society. When this merger, was effected, a proviso was made that the books contained in the Institute library up to the date of the merger were still to be considered as the individual property of the Institute, and this arrangement applied also to the libraries of the other two Founder Societies. At the time that the American Society of Civil Engineers joined as a fourth Founder Society, they immediately turned over their entire library to the United Engineering Society, relinquishing all property rights in the books entirely.

Jan 2, 1917

Within the last century, and largely during the latter half of it, the increase of our knowledge of the development of man, both in his search for a livelihood and for power, and in the growth of his reason and conscience, has been greater than all we had known before. The great interest in all kinds of archaeological work and the many excavations made of buried and long forgotten places has put at our disposal historical records-not available, and in many cases not known before, and a study of these and other records of human progress from paleontological and geological sources has given us a much broader view of what we call "civilization" than was possible even a short time ago. The old idea that men were created with fully developed minds, speech and reason has yielded to the view that in the upward progress of the human race the development of the mind and reason has been a comparatively recent occurrence, as we think of the half million, and probably more, years that have passed since our earliest records of man were made. The traits that come to us without effort

Jan 1, 1939

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By G. Derge, M. Bourgon, G. M. Pound

A STUDY of electrical conductance in molten Cu-Fe sulfide mattes' has shown that pure molten Cu,S behaves like a semi-conductor in that it is an electronic conductor and its specific conductance, of the order of 100 ohm-' cm-', increases with increase in temperature. On the other hand, pure molten FeS, another electronic conductor, behaves like a metallic conductor in that its specific conductance, about 1500 ohm-' cm-', decreases with increase in temperature. Molten solutions of Cu,S and FeS follow a roughly additive rule of mixtures with respect to both specific conductance and temperature coefficient. The behavior of molten Cu,S may be understood, by analogy to the situation in solids, in terms of semiconductor theory.' It is thought that, although the melt consists of cuprous and sulfide ions, the bond between these atoms has a certain degree of cova-lency. According to the simplest concept the electrons in the partially covalent bonds are thermally promoted to a conduction band. In another concept, small amounts of impurities (undetermined) provide donor or acceptor levels in the forbidden zone between the valence and conduction bands and thus facilitate semi-conduction in the usual way. However, the metallic behavior of molten FeS is difficult to explain, because one might expect from similar reasoning that it too should act like a semi-conductor. It was suggested that the apparent metallic behavior of molten FeS might be explained by a large negative temperature coefficient of density. Thus if molar conductance instead of specific conductance were plotted versus temperature, the slope might prove to be positive, indicating semi-conduction instead of apparent metallic conduction. Accordingly, density measurements were made in order to answer this question in regard to molten FeS and also to provide data for conversion of specific conductance to molar conductance for molten Cu,S and a molten 50-50 wt pct Cu-Fe sulfide matte. Experimental Diagrams of the apparatus are given in Figs. 1 and 2. A 3 x 8-cm dense alundum crucible containing the prefused specimen is positioned in the uniform temperature zone of an induction furnace tube and melted under a helium atmosphere. Then the cell assembly, consisting of two 3-mm spectro-graphite rods, one of which is in a 1-cm ID open

Jan 1, 1959

Tooele Flue-type Cottrell Treater Discussion of the-paper of A. B. YOUNG, to be presented at the New York meeting, February, 1921, and printed to accompany MINING AND METALLURGY No. 162, June, 1920. HARRY V. WELCH,* Los Angeles, Calif. (written discussion).-The basic requirement in the electrostatic process of electrical precipitation is that gases containing solid particles in suspension are forced to pass through an electrical field consisting of an insulated high-potential wire, or other type of discharge member, and a grounded plate, or other, type .of collecting member. Commercial. operation and efficiency of precipitation are secured by electrical and structural arrangements to provide the maximum value of the variable factors modifying the degree of precipitation. That is to say: 1. A unidirectional flow, of high-potential current is vastly more effective in precipitation than a high potential alternating-current flow.

Jan 2, 1921

Charles Mather MacNeill, President of the Utah Copper CO. and of the Chino Copper Co., and a life member of the Institute since 1899, died at his home in New York on March 17, after a very brief illness with pneumonia. Mr. MacNeill was born at Oak Park, Ill., in 1871, and began his connection with mining enterprises immediately after graduating from high school, his first position being that of cashier with the Pueblo Smelting and Refining Co. He later went to Aspen, Colo., as manager of the Holden lixiviation plant. In 1893, he went to Cripple Creek as manager of the Lawrence Reduction Works, in which Mr. Holden and the late Capt. J. R. DeLamar were large owners. It was at this plant that Mr. Jackling became associated with him. The plant was destroyed by fire and, early in 1894, Mr. MacNeill became associated with Messrs. Spencer Penrose and Charles L. Tutt in a plan to finance and erect a chlorination plant at Colorado City, Colo., for the treatment of Cripple Creek ores. This plant was erected and was known as the Colorado-Philadelphia Reduction Works. Mr. MacNeill was general manager of the plant, Mr. Tutt having been president and Mr. Penrose, secretary and treasurer. The plant was very successful and was expanded, hally being reorganized under the name of the United States Reduction & Refining Company. Late in 1903, or very early in 1904, D. C. Jackling called the attention of Messrs. MacNeill and Penrose to the copper properties in Bingham Cañon, Utah, which have since become the main properties of the Utah Copper Co. After extended examinations and milling tests, these properties were bought, Mr. MacNeill becoming president of the Utah Copper Co., Mr. Penrose, secretary-treasurer, and Mr. Jackling, general manager. Mr. MacNeill remained president of the company to the time of his death. Mr. MacNeill was also a director, a member of the executive committee, and was largely interested in the Ray Consolidated Copper Co.; he was also president and a member of the executive committee of the Chino Copper Co. He had a variety of other mining interests, but the ones mentioned were distinctly the meost important. He was a director

Jan 1, 1923

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS,. ALBERT SAUVEUR. Columbia F. A.. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 12, 1914

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICKARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant Admissions RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON DONALD M. LIDDELL WILBER JUDSONW. D. B. MOTTER, JR.

Jan 1, 1934

By G S. B Karunatillake

Following a pre-feasibility study, Mount Isa Mines commenced a feasibility study on the deposit of the George Fisher Mine in May 1997. Board approval was granted in May 1998 to construct a 2.5 million tonne per annum mine and to upgrade existing concentrator and smelter facilities. The world-class George Fisher zinc-lead-silver deposit is located approximately 22 kilometres north of the city of Mount Isa, in north-west Queensland and is 2.6 kilometres north of the existing Hilton Mine. It will be a large-scale underground mine, sustaining a profitable zinc-lead-silver business in Mount Isa for at least ten years. This paper will outline the details of the mine that was developed during the feasibility and design phase. It will include a description of the mining methods, ventilation, fill, ore handling, services and infrastructure. The utilisation of existing assets and the development of innovative ideas were essential to the successful economic development of the George Fisher Mine.

Jan 1, 2000

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 8, 1950

By C. Kremer Bain

UNDER present economic conditions the necessity of mechanizing the mines of our country has become a very important problem. More and more mines are looking toward increased or complete mechanization of their operations, so in the writer's opinion it is quite pertinent that some of the associated problems that accompany such a program be pointed out. The following generalization on attempting a comparatively slight change in mining methods at the Southeast Missouri properties of the St. Joseph Lead Co. is an attempt to point out to anyone faced with a mechanization program that much time and C. KREMER BAIN, Member AIME, is Assistant to General Manager, St. Joseph Lead Co., Bonne Terre, Mo. AIME Sun Francisco Meeting, February 1949. TP 2743 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Dec. 27, 1948; revision received Oct. 13, 1949. effort can be saved, and many headaches avoided, if company policy can be established whereby everyone in the organization from the top down is desirous of improvement and is working towards the common objective. Any changes in mining methods, machinery, and so on, must entah coordination of all the other phases of mining as they all have to mesh as accurately as a smooth running chain of gears if satisfactory results are to be obtained. The purpose of this paper is to point out some of the problems which :have to be surmounted when any mechanization program is attempted, rather than to go into the mechanical details and actual operating data of the equipment employed. After all, machines have to be adapted to best suit the local conditions, so no general formula can be given that would apply to other properties. Although St. Josepll Lead Co. has been mechani-cally-minded for a number of years, as shown by the fact that over 110 million tons have been loaded mechanically since 1922, any further mechanization or changes always present a problem. When our ore bodies were of great height and area the breaking and loading were developed to a high degree of efficiency according to known standards. But in recent years, when our ore bodies became smaller and more scattered, the amount of tonnage we were able to break was not sufficient to supply our shovels with enough rock to keep them working to capacity. Our first step in attempting to rectify this situation was to develop a technique of moving the shovels to the broken ore in various stopes, which sometimes entailed a move each shift. A shovel is not producing when being moved, so within the last two years we have been endeavoring to devise some means of getting more rock broken in these smaller stopes and it was then that we became interested in jumbo drilling. To illustrate the fact that mechanization is a process of a chain of developments rather than a stroke of genius can best be shown by a general summary of conditions and obstacles which were encountered in our present attempt to establish template drilling of a standardized round. Our first jumbo was more or less the conventional type with two machines mounted on a crossbar. This arrangement proved to be impractical to duplicate satisfactorily the regular routine of slabbing in a more or less radial pattern as carried out by column drilling. One machine was either too close to or too far from the face and there was another disadvantage in that one drillman was frequently delayed while waiting for his partner to bottom a hole. Our next step was to eliminate the crossbar so the machines could operate independently of each other, but we still encountered the same objections mentioned above except that one drillman was free to drill three holes instead of one in a vertical plane independently of his partner. Time studies while trying to adapt the jumbo to the regular slabbing practice as accomplished by column drilling, revealed that twice as much time was spent in maneuvering the jumbo into position and aligning the holes as was consumed in drilling.

Jan 1, 1951

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By A. C. Lordi

Present industrial plant design is influenced by motivators beyond the usual powerful one, creativity, on which Consultants thrive. The respected, although annoying, ever-present Return on Invested Capital becomes even more significant with anticipated escalation. Government regulations are having an increasing influence as air and water protection, sound and electrical safety requirements must be met And more recently, the increasing cost and uncertain availability of energy sources are having a revolutionary affect on plant design. More than ever before, the Consulting Engineer is faced with requirements and restrictions which tax even the most original thinkers -- and the result is good. This paper includes a brief review of recent trends in Cement Plant Engineering Design.

Jan 1, 1975