Search Documents

By G. Ladouceur

"Northgate Patino Mines produces a copper concentrate assaying 22% Cu. Moisture content of the product averages 12.5% H20 when dewatering with conventional vacuum disk filters. Recent smelter contracts reflect higher energy costs and increased moisutre penalty charges. This situation forced Northgate to investigate possible alternatives such as rotary dryers and pressure filtration. After laboratory testing, it was found that pressure filtration could economically meet the smelter's requirements. Pilot plant testing was then undertaken and confirmed the laboratory test results. Based on these findings, a model I.S.F. 1500 x 28/22 I.R. Lasta filter press was purchased.This paper describes the Copper Rand dewatering flowsheet the operation of the press and the economics of the process.IntroductionNorthgate Patino Inc. operates 2 und erground copper mines and a 3300 ton per day concentrator located in Chibougamau, Quebec, some 425 miles north of Montreal and 300 miles northeast of Noranda, Quebec.Copper concentrate is produced at a rate of 250 tons per day and trucked to a C.N. siding 10 miles from the mill site and then railed to the Noranda Smelter.Until early 1981, moisture content of the concentrate at 12.5070 was acceptable since smelter penalty charges were relatively low ($0.10 per ton per unit over 10070 moisutre). In January 1981, a new contract was signed in which the penalty was raised to $1.10 per ton per unit over 8070 . This and the increasing truck and rail costs justified the change-over from vacuum to pressure filtration . The Lasta I.S .F. 1500 x 28/22 was then purchased and installed, and operation of the plant started in December 1981."

Jan 1, 1987

By M S. El Salmawy

In order to develop the HF-free flotation reagent system, the main objective of this investigation was to study the possibility of separation of quartz from feldspar using non-ionic surfactants as the collector. The non-ionic surfactants used were polyoxyethyl cethyl ether (PECE) and polyethylene glycol monocethyl ether (PGME). The flotation behaviour of quartz and microcline with PECE and PGME was investigated. Each surfactant was a good selective collector for quartz with its recovery being influenced by pH and surfactant concentration. Quartz is floated favourably by both types of polyoxyethylene non-ionic surfactant whereas microcline was not so much. The floatability of quartz increases as the oxyethylene length of surfactants increases. Zeta potential measurements in the system of PGME/mineral were also carried out. It was determined that in the absence of PGME the points of zero charge for quartz and microcline should be approximately at pH 2.5 and 1.8, respectively. The addition of PGME to the system causes both minerals to become less negatively charged. Differences in the zeta potential value between quartz and microcline, in the presence of PGME, were detected. It can be suggested that the interaction of the oxyethylene group to the microcline surface should not be as strong as that to the quartz surface. In the mixed surfactant system of PGME and dodecylamine acetate (DAA), a small addition of DAA causes drastic enhancement of quartz flotation in the wide pH range of 1 ~ 10. In the mixed surfactant system selective flotation of quartz from microcline would be anticipated at pH

Jan 1, 2005

By William H. Shockley

Though China has been widely explored by mining engineers during the past dozen years, comparatively little has been published concerning its mineral resources. The few moilographs scattered through the transactions of various societies contain far less information than the private reports made to the numerous syndicates which have sent out engineers. The best general account of the geolopy and mineral resources of China is to be found in the works of von Richthofen,' a remarkably gifted observer. The observations recorded here in this paper were made in the service of the Pekin Syndicate (which has kindly given me permission to publish them), during the first months of 1898, among the coal- and iron-fields of southeastern Shansi. This is one of the largest anthracite-regions known, the area being

Jan 1, 1904

By Charles E. Stack

There are several ways in which to classify refractories. The most suitable one is based on their general composition or raw material content. The categories are: 1. Aluminosilicate brick which include the fire clays and alumina and high alumina raw materials. 2. Basic brick which includes magnesia and chrome ore alone and in various combinations. 3. Silica brick which uses gannister or high purity gravels and sands. 4. Insulating brick are generally of the aluminosilicate type but may be most all refractory raw materials. 5. Special refractories are made from raw materials of zircon, zirconia, ultra high alumina, silicon carbide, fusion cast products, chromic oxide, carbon and graphite. The raw materials that make up these different categories are what we are briefly going to consider. Emphasis is placed more on the most important raw materials.

Jan 1, 1976

[ ]

Jan 1, 1938

By Tomás Cayao, Mariana Sce, Leonid Merebashvili Zarogatsky

En el caso de la tecnología de Impulso Vibratorio se inducen, en el material, vibraciones a alta frecuencia, las cuales fatigan las estructuras del material y lo desintegran. De este modo se logra aumentar varias veces la eficiencia energética y obtener un producto de mayor calidad tanto en el grado de liberación como en la morfología. En este artículo se describe la tecnología de Impulso Vibratorio y el diseño de las máquinas que utilizan esta tecnología, Además, se muestran los resultados de una serie de ensayos llevados a cabo con el fin de validar dicha tecnología.

Sep 1, 2017

By C. O. Petter

This paper, in its first part, compares the profile and economic weight in the extraction of industrial minerals and aggregates to the so called conventional mining activities (metals, coal, gas and oil extraction) in Brazil. In its second part, a descriptive analysis of the present situation of the education in Brazil is made, emphasizing the graduation and post-graduation formation especially in engineering. The curricular structure of the schools that prepare the mining workforce is discussed and the presence of specific subjects in industrial minerals is evaluated. Finally, considerations are made on the actions being taken in the main universities and companies, aiming to improve the formation of the specialized workforce. The Brazilian mining production, comparing 2010 to 2011 showed an expansion of more than 3% (IBGE, 2012). Not bad, but nothing to do with the 13% growth between 2010 and 2009 (influenced by a recovery effect from the 2008 commodities? nightmare). The commodities that had a rising behavior were titanium, gypsum, nickel, graphite, bauxite, phosphate, chrome and chrysotile. All of them were eclipsed by the impressive growth of iron ore production. Some decreases could be noticed, eg. in zinc, kaolin, magnesite and salt production (DNPM, 2012). In fact, the mining activities followed the positive growth of the country these last 5 years. The commercial balance (exports against imports) was not spectacular (positive in US$ 30 billion in 2010). It is important to notice that the mineral commodities balance was US$ 35 billion, representing 27.4% of the total exports and 15.6% of the total imports of Brazil (DNPM, 2012). In this positive environment, the workforce in Brazil showed progress in number of formal jobs and average revenues.

Feb 23, 2014

By R. Bonifaz

The Chagres Smelter, part of the Anglo American plc group situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant application of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studying various options for investment suitable for a profitable business of benefits to both Anglo American and Chile as a whole. The most relevant technical indicators are the figures : Energy consumption less than 6,3 GJ/ton fine copper, Intensity of smelting rate in Flash Smelting unit of 6900 ton of copper concentrate/m2 settler of furnace area and be one of the top five smelter in direct cash cost .

Jan 1, 2007

By R. A. Wagstaff

THE method of charging a reverberatory furnace has changed many times since smelting was introduced in this country from the old smelters of Swansea, England. The cause of the latest change at the Garfield plant has been the excessive fineness of the charge due to fine grinding in the concentration of the crude copper ores. The many desirable features of deep-bath smelting as now used at Garfield have been proved. The old method of dropping the charge through holes in the arch (known as center-feed method) causes excessive dusting which makes heavy slag and causes flue-dust losses, also rapid deterioration of the silica brickwork of the furnace through fusion .with the iron oxides from the dust. The purpose of this paper is to describe a gun feeder that was designed to overcome the disadvantages of the older methods of center feeding and still maintain the good features of deep-bath smelting with the hot finer charge. A gun feeder was designed to introduce the finely divided hot calcines under the moving gas stream of the combustion zone and still have them spread in a uniform blanket over the highly heated matte bath. The temperature of the furnace was so great that it was impossible to maintain a stationary feeder, so a movable feeder was designed that could be introduced into the highly heated zone and be withdrawn after the charge had been dropped. It was necessary to protect the nozzle of the gun with a water-cooled coil. Many different types of protected nozzles were tried, such as air jackets, water jackets and heat-resisting steel alloys, but none proved satisfactory.

Jan 1, 1932

By Ernest Stütz

(New York Meeting, October, 1913.) THE problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been. submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Düsseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Düsseldorf meeting : ?The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized,, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost 'of briquetting a ton of ore, but what, in. using ore briquettes, is the cost, of: production of a ton of iron."

Jan 7, 1913

By J. A. Chermak, D. D. Runnells

Sulfide-bearing waste rock, ore and tailings have the potential for generating acid rock drainage (ARD) when exposed to an oxidizing environment. The possibility exists of utilizing the acid produced to react with lime and/or limestone to form a self-sealing cap on the reactive waste rock and tailings. Laboratory column experiments were conducted using acid-generating waste rock with a surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results demonstrated that the limestone and lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxyhydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on the results of this study, it should be possible to create hardpan layers as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic waste rock or tailings material in the field. Unlike traditional capping methods, e.g., clay and high-density polyethylene (HDPE) covers, chemical caps should be self-healing.

Jan 1, 1998

By E. B. Swanson

FREQUENT reference has been made to the increased domestic gasoline demand recorded for 1931. This increase was in the neighborhood of 7,000,000 bbl. Although smaller relatively than that to which the oil industry had become accustomed by virtue of the experience of preceding years, the increase was of substantial amount, particularly at a time when any increase at all could be regarded with eminent satisfaction. Less has been said, however, of the 18,000,000 bbl. decline in gasoline shipments to territories and foreign countries. When the loss of business outside the United States is combined with the domestic increase, there results a net loss of some 11,000,000 bbl._ in total gasoline demand. The gain of 2 per cent in domestic sales gives way to a loss of 2.5 per cent in total domestic and foreign sales. The United States actually has been losing ground in the international gasoline market since 1924, when shipments from this .country equaled 72 per cent of the gasoline shipments from the leading gasoline-producing countries of the world. A loss in relative standing was recorded with each succeeding year. As long, however, as gasoline shipments showed an actual increase, the loss in relative standing was of little concern. Foreign producing centers annually supplied an increasing share of the foreign gasoline markets, but, until the past year, the demand abroad con-tinued to increase at a pace which could accommodate all of the, increased output of foreign plants and yet require increasing quantities from the United States. It was not until 1931 that the various factors were combined so as to produce an actual and substantial decrease in the foreign demand for United States gasoline. Consumption in foreign countries generally declined, while the output of foreign refineries and the foreign manufacture of substitute fuels continued to increase. From our own viewpoint, this meant a loss of some 18,000,000 bbl. of gasoline busi-ness in foreign countries, one-half of it probably due to the lowering in foreign demand and the other half to the increased output of foreign refineries and the increased utilization of substitute fuels.

Jan 1, 1932

By L. M. Pidgeon, P. G. Thornhill

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. lengtn of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of ¼ in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10o to 15oC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press Operating at a temperature of 140°C

Jan 1, 1958

By R. S. Shoemaker, F. W. McQuiston

ECOLOGICAL CONSIDERATIONS IN CYANIDATION PLANT PRACTICES Ecological controls of tailing storage pond effluents are mainly concerned with mercury and residual cyanide and are critical problems for gold and silver recovery plant operators. For example, mercury for direct amalgamation of gold ore was used at Homestake until 1970 when the Federal Government acted to prevent further use thereby forcing the abandonment of this practice. However, mercury is still used at Homestake, in South Africa, and also in some Philippine and Canadian cyanide plants for barrel amalgamation of free gold gravity concentrates. The amount of mercury involved in South African practice is about 150 ounces for every 100,000 tons of ore milled and which reaches the tailings ponds. In South Africa, it is obligatory that no pond effluent be discharged beyond the mining property boundaries and waters containing mercury and cyanide must be evaporated either on the tailings pond or in specially constructed evaporation dams. In some cyanide plants such as Carlin and Cortez in the United States, all supernatant solution from the tailings ponds are returned to the plant for reuse. When all solution cannot be reused, the excess may be evaporated in shallow ponds, or by spray systems inside of the tailings dam. Such plant reuse of tailings effluent depends strictly upon the degree of contamination or "fouling" of the barren solution and tailing water with cyanicides. Foul solutions that cannot be returned from the tailings pond may be effectively cleaned up by cyanide regeneration. Cyanogens in plant solutions exist chiefly as free alkali cyanides, as zinc and copper double cyanides, as sulphocyanides, and as ferrocyanides. From the free cyanides and zinc double cyanides, substantially complete recovery of the cyanogen is easily effected. Part of the cyanogen combined with copper is also recovered; regeneration of the remainder with the cyanogen existing as sulphocyanide and ferrocyanides requires special treatment. At this stage, it would be generally more practical to eliminate the remaining cyanogen by chlorination. Ecologists have also been concerned with pollution of ground waters from cyanidation plant tailings. An accute problem is solution seepage down stream from tailings dams and strict attention to prevent or collect any seepage is a real necessity. The tolerance levels of the total cyanide content in potable water set by several U. S. and State health agencies are 10 ppb, and 20 ppb discharged into ground waters. The cyanide content so established is, strangely enough, based on the survival tolerance of fingerling trout. Decanted waste water from tailings dams may be effectively treated by the use of alkaline chlorination for the purpose of destroying all cyanide compounds. The alkaline hypochlorite used to oxidize the cyanide to cyanate is applied as such or generated within the waste solution by adding caustic (NaOH) and chlorine gas. A second chemical reaction involves complete destruction of the sodium cyanate.

Jan 1, 1975

By Silvana B. Foá

Results from full-scale loading tests showed the use of the dynamic increasing energy test (DIET) to verify the capacity of deep foundations. This method allows the measurement of dynamic resistance - displacement curve and the prediction of the static resistance -displacement curve of the pile-soil system. The comparison between the use of DIET versus the static load test is also considered herein. This work was divided in two different phases, the first accomplished in Salvador (Bahia) and the second in Brasilia (Federal District), both in Brazil. The first phase consisted of field loading tests carried out on piles comprised by an approximate 10 to 12 meters thick deposit of fine saturated sand, overlying a stiff clay layer, which is found in certain areas of the Brazilian Northeast. Two metallic (rail track) piles were field loaded in this site. One of them was dynamically tested and the other was statically tested. The second site belongs to the Post Graduate Program of the University of Brasilia. It is comprised by an approximate 8 to 14 meter think deposit of porous clay, overlying a hard strata of saprolitic state. In this site a unique precast driven centrifuged pile was tested. The DIET procedure has demonstrated to be a tool of fast execution and low cost (if compared to static load test). It is a promising procedure to evaluate the behavior of pile-soil system.

Jan 1, 2002

By Z. Sample, S. Kaushik

"INTRODUCTION Industries around the globe have been making significant advancements in recent years due to innovations in automation technology. With the implementation of modern automation technology, professionals in process automation or plant operations can expect significant and exciting change, and the mining and mineral processing industries are no exception. From 2000 to 2010, the International Council on Mining & Metals (ICMM) reported that an increased output and increased value of most metals has resulted in a rise in global metal and mineral process industries from $214 billion to $644 billion. [1] Since most productivity increases in mining and mineral process industries have been achieved through the ability to process lower grade ores with improved efficiency and larger equipment, these industries have begun to adopt advanced automation and control technologies. Despite a growth slow-down, the mining and mineral processing industries are poised for continued and sustainable growth and development due to an increasing demand for energy minerals and emerging technologies requiring minerals and metals previously not demand. However, as these industries becomes more automated, new challenges are arising on the horizon. DEMOGRAPHIC TIME BOMB John Payne from BP is credited with first using the term Demographic Time Bomb to describe the upcoming crisis in the process industry in finding experienced operations personnel. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years. This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, this implies that these skilled mining and mineral process professionals are an aging population with irreplaceable knowledge and experience that are expected to retire in the next 5-10 years. While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences."

Jan 1, 2015

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By Carlos R. Tapia

"El presente trabajo describe los métodos de explotación aplicados en la mina Carahuaca, así como una breve historiografia y contexto del yacimiento minero. En este punto, registra la ubicación de la zona minera en la provincia de Yauli, departamento de Junín, cuya geología desarrolla tres depósitos minerales tales como el depósito Norte o principal, el depósito central o viejecita y el depósito Sur o pantano. El sistema de explotación se da a cielo abierto (sistema de bancos), y pertenece a una zona mineralizada y subterránea (tajos de corte y relleno y sin entibación), la misma que se divide en dos operaciones: la remoción de la zona estéril del pendiente de la zona mineralizada y parte del yacente para dar a los bancos la inclinación final y la subterránea( tajos de corte y relleno aislados por entibación completa con cuadros ensamblados). Por último, se encuentran las labores de exploración y desarrollo que descubren, bloquean y atacan las secciones del mineral explotable (recortes y galerías, enmaderación y profundización del pique maestro al nivel 50)."

Jul 20, 1955

By Fuzail Siddiqui

"The SIDMIN program aims at filling the mineral processor’s need to know the deportment of ‘minerals of interest’ not just ‘elements of interest’ that pass through the processing plants. Generally, chemistry is used as a tool of routine monitoring on site. Mineralogy, which is relatively much slower, is used more as a tool of research and post mortem investigations and these services are usually provided by a distant facility. The SIDMIN program enables site management to receive chemical and quantitative mineralogical reports on their critical samples daily, simultaneously and affordably.The author developed the SIDMIN program at ZCCM Nchanga Division where it continues to be a powerful tool for monitoring the efficiency of operations. Outlines are given of procedures for quick sample preparation and quantification of significant minerals in process samples. A specimen report is presented, which shows the format of reporting the contributions of individual minerals to metal losses at critical stages of the circuit. It is shown that SIDMIN provides timely information to management, about trends and abrupt changes in the quality of ore, and its processing, in a way never achievable by chemical analyses alone. This greatly helps in resolving the age-old problem of ‘bad ore’ or ‘bad operations’ on a day-by-day basis. For example increase in copper mica in the feed indicates excessive ore dilution during mining. Increased loss of free sulphides was traced to insufficient reagent conditioning time at the Concentrator. Persistent losses of leachable oxides at the Tailings Leach Plant were traced to inadequate leach residence time.SIDMIN is affordable because it can be implemented using basic optical microscopes, minimal quantities of micro-chemical reagents and custom trained site staff who demonstrate good colour perception and an ability to follow laid down procedures consistently."

Jan 1, 2000

By C. Melvin Lepper

The Bureau of Mines has developed an improved earth resistivity field system which employs a novel technique for obtaining null measurements. The instrument is designed to operate reliably in high-noise environments such as those found in the vicinity of operating mines. The system consists of a low-frequency transmitter, a sensitive receiver and an external battery pack, each in its own case to provide protection from the elements. The receiver and transmitter units have self-contained recharge-able batteries to supply power to the circuitry and separate built-in battery chargers that operate on standard 115 Vac power. The system is portable and simple to operate. Measurement accuracy, reliability, and dynamic range are superior to most commercially available equipment even though less time and effort is required to make null readings. Unlike some commercial systems, long integration times are not required to enhance signal-to-noise ratio in areas of high background noise.

Jan 1, 1974