Search Documents

By F. C. Muttitt

The physical arrangement of the continuous casting facilities at Algoma have been described a number of times in previous papers. For the purposes of this discussion, it is sufficient to state that the casting plant is located at a considerable distance from the basic oxygen shop which supplies it, involving a relatively lengthy ladle transfer movement. (Fig. I) The handling of the ladle by two separate cranes, first to the argon station, and thence to the casting machines, results in an average interval, from start tap to start cast, of 45 minutes. The effects of such extended retention time on temperature control and on refractory performance are well known. Tapping temperatures well above normal are necessary to insure that the ensuing heat losses do not result in an undue incidence of premature tundish freeze-offs. The heat lost, as well as being a function of the retention time, becomes more critical with smaller ladle size; winter temperatures add to the problem with their effect in chilling ladles and increasing radiant losses.

Jan 1, 1972

This brief resume of the events transpiring in Mexico, culled from the daily New York newspapers since the last Bulletin went to press, does not show any degree of improvement in the situation. U. S. WITHDRAWS ARMY FROM MEXICO The American invasion of Mexico lasted less than 24 hours. The troops which crossed the Rio Grande June 15 to put a stop to the firing that was causing death and injury in El Paso were back in their billets on the American side of the border the next night. They had broken up the battle between Villa rebels and the Carranza garrison and driven the rebel forces headlong out of Juarez and into the hills. The Carranza Consul, Garcia, and Gen. Francisco Gonzales are reported by American officials to be pessimistic, if not indignant, at the swift reprisals made by the Americans against the stray shots which were falling in El Paso during the Villa attack on Juarez. In announcing his action in ordering Americans into Mexico Brigadier General Erwin in a formal statement said he had done-so to prevent the indiscriminate firing into El Paso by rebel soldiers, endangering the lives of Americans. "But on no account were they to undertake an invasion into Mexico," continued the statement. Americans with interests in the vicinity of Chihuahua are alarmed lest Villa, smarting under the defeat administered his troops by the American forces, should make a campaign of destruction. General Candido Aguilar, President Carranza's confidential ambassador to the United States, issued to the press, on June 17, a formal statement that "the government and people of Mexico consider as a violation of Mexican sovereignty the crossing of United States soldiers into Mexican territory" and expressing the hope ?that the situation created by the latest occurrences in Juarez will be satisfactorily adjusted between the two countries." Discussion of Mexican affairs was evoked in both houses of Congress by the crossing of the Rio Grande by American troops.

Jan 8, 1919

By William L. Lennemann

Chemistry of uranium with respect to its hydrometallurgical recovery from carnotite ores was investigated and well defined during the radium boom period between 1900 and 1920. Since that time, methods used to extract uranium from its ores have remained basically either acid leaching or sodium carbonate leaching. Until about 1950, the only practical methods known for achieving a better than 75 pct U2O3 concentrate from the leach liquors involved fundamental chemical techniques for either purifying a solution prior to the uranium precipitation, or refining a crude uranium concentrate that was produced by neutralizing a pregnant mill liquor.

Jun 1, 1956

By Edgar C. Bain

Of the important phenomenon of the hardening of steel, Professor Sauveurl says: It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say this of other problems. It seems likely that one of the new avenues of approach to many metallo-graphic problems is the study of crystal structure, or more accurately, the atomic arrangement, by means of the x-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of x-rays by Laue and the Braggs2 and later by HullI3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the x-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 1, 1923

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

By Charles K. Rose

This paper presents some research studies of the rotary drilling of oil shale at the Bureau of Mines Oil-Shale Mine, Rifle, Colo. The experimental procedures and the rotary drill test equipment are described. Theories of rock drillability, rotary bit cutting action, and bit design are presented and discussed. The actions of various bit designs are analyzed and compared with the observed results of actual drilling tests. A cost estimate is made for drilling Colorado oil shale.

Jan 1, 1955

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

Jan 1, 1932

By R. Moldenke

The presence of nickel-chromium in pig iron made fro111 Cuban oles is so well known that the word "Mayari" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there llas been increasing interest in these ores. Tlie Transactions contain numerous references to t1ieln.l This iron ore, which is shipped to the Tinited States in the nodulizecl state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of RInpari ore for pig iron for the better grades of finishrtl iron products. The present point of coilsn~iil)tion ol ILlapri ore is at Sparrow's Poi111, where hlayari pig iron of ally desiretl coml>osition is made. The composition of the dried ore is about as follows: Iron -29 per cent., silica 3 pc.r cent., nickel 1 per cciit., chroiniun~ 1.5 per cent., alumina 11 per cent., ant1 coinbined water 13 per cent. When nodulized, the iron runs up to nearly 56 per cent., the silic:~, :tlumi~i:i, nickel, and c~llromiurn are slightly highr than the arno~l~its just given. Practically all the, combined wntcr is driven off aild the iiodulizccl ore carries only a few- tenths per cent. of 1 C. M. Weld: Residual Rrolvn Iron Ores of Cuba. Tmns, (1909) 40, 299. C. K. Leitll nnd If'. J. Mcncl: Origin of Iron Ores of Central and Northeostr~n rlbn. Trans (1911) 42, 00. C. W. Hayes: May:~ri and Mos Iron-ore Deposits in Cuba. Idem, 109. J. E. Little: Maynri lron Mincs, as Developed by the Spanish-American Iron ('0. Idem, 152. J. F. Iie~np: M'ryari Iron-ore Dcposi(s. Trans. (1915) 61, 3. C. K. Leith 2nd N. J. Mead: Additional Data on Origin of Lateritic Iron 01cs or Eastern Cubn. Tmns. (1916) 63, 75.

Jan 1, 1923

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By E. L. Fidler, T. E. Finch

Wayne Anderson Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 11, 1982

By D. Pearson

INTRODUCTION In 1975 278x10 3 tonnes of zinc was consumed in the United Kingdom, of which 69.3x10 3 tonnes was obtained from secondary sources. Of this secondary zinc 37.7x10 3 tonnes was used in brass making, the remainder was used in non metallic applications - eg oxides and salts. Many forms of zinc-bearing wastes arise, for example as galvaniser's drosses and residues, fumes from ferrous and non-ferrous metallurgical processes, and filter cakes from rayon manufacture and metal finishing. In the case of zinc-bearing dusts and fumes, the quantities available for recycle are at present restricted by the failure to collect them efficiently, hut environmental factors are leading to improvements in gas cleaning, with the result that quantities collected will increase and then exceed those required for the production of chemicals, so that some dusts may either have to be dumped or processed to metal. The recovery of zinc from steelmaking dusts is practised in W. Germany (1) and Japan (2) employing processes based on reduction in rotary kilns in order to produce sponge iron and a zinc- rich oxide suitable for feeding to the zinc-lead blast furnace. Although the zinc-lead blast furnace is the only zinc-making process used in the UK, no similar treatment of steelmaking dusts is carried out, a pilot scheme was tested by the British Steel Corporation, but development was abandoned for economic reasons. It appears to be cheaper to pelletise suitable dusts and export them for treatment elsewhere.

Jan 1, 1981

By C. M. Ball

The very considerable progress made during the past three years in the crushing and concentration of ores, lends special interest at the present time to any means of a more efficient character than such as are already generally known and in use, for the rapid and regular reduction of large quantities of the harder and heavier grades of mineral-bearing rock. Such means are of exceptional importance in connection with the preparation of iron-ore for separation by the magnetic process, since in this operation the capability of dealing with large volumes of material and of securing by ready means of adjustment, a granulation of the material under treatment to any required mesh or fineness, is of the greatest possible value. With these, however, must be coupled the further considerations of the amount of power expended for the work done, and the wear and tear, represented in the cost for renewal of parts of the crushing machinery, per ton of material reduced to a given degree of fineness. In general terms it may be stated that the operation of a crushing train, capable of reducing an ore-rock of average density and hardness, from the condition of mine lumps to pass 1/16-inch screenopenings at the rate of 20 tons per hour, should not call for an expenditure of more than 125 horse-power, and that the wear and tear of the crushing machinery, all told, should not exceed 2 cents per ton. In the design of a crushing-train for an ore-dressing plant, there are, moreover, considerations of great importance which relate to the simplicity or complexity of construction and arrangement, the wear and tear of few or many elements, the easy ability or difficulty of maintaining the working adjustment of the various elements of the train, and the number of hands required for the operation of the system. With these points in view, it is thought that the Cummings ore-

Jan 1, 1893

By Dr. R. W. Mead

There are two basic problems when one attempts to separate a solution of metal ions utilizing a chelation-solvent extraction cascade (commonly called liquid ion exchange). First, it is impossible to produce any great degree of separation unless the separation factor (also called selectivity, which is the ratio of the distribution coefficients) is very large. Second, the richest possible extracted product, using an infinite number of equilibrium stages, is at best only in equilibrium with the feed solution. These factors combined with equipment design considerations have led to a situation where only the most selective chelating agents are applicable to economic industrial operations. The authors know that distillation techniques are used routinely to separate compounds with nearly identical relative volatilities and that there should be a way of operating solvent extraction cascades in an analogous manner to obtain separations of metal ions. The advantage of this approach would be that solutions of metal ions of any desired purity could be obtained even if the separation factor was close to unity. This paper presents this idea and suggests some possible applications.

Jan 1, 1977

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Gordon C. Hicks

Prior to 1950 most fertilizer manufactured in the United States was produced in a nongranular form. In such form, the material caked when stored and was extremely dusty when applied in the field. About this time a wide interest developed in the fertilizer industry for the manufacture of a granular, high-analysis fertilizer of improved physical properties. Thus, TVA began work on fertilizer granulation about 1950 using both a pugmill (double-shaft paddle mixer) for a thick slurry of nitric phosphate and a continuous ammoniator-granulator drum for superphosphate-base mixed fertilizer. Granulation in these units was mainly by agglomeration. The liquid phase generated by the moisture and by the heat of reaction of ammonia with acidic materials, such as superphosphate and sulfuric or phosphoric acids, resulted in agglomeration of the solid ingredients. About 1956, TVA began studies of the use of a pan or disk granulator for production of ammonium nitrate or other fertilizers containing a large proportion of ammonium nitrate, such as 30-10-0 ammonium phosphate nitrate. This is the layering method of granulation. More recently, TVA has demonstrated pan granulation of urea from a highly concentrated solution and granulation of ammonium polyphosphate melts in a pugmill. The bulk of TVA studies throughout the years has related to use of the drum granulator. About 200 granulation plants in the United States have been licensed and built to use the TVA continuous ammoniator-granulator; it is estimated that more than half of the 20 million tons of mixed fertilizer used in the United States in 1974/1975 was produced in these plants. Some other granulation processes developed for use in the drum granulator include diammonium phosphate, monoammonium phosphate, urea- ammonium phosphate, ammoniated superphosphate, and most recently, NPK fertilizers by melt granulation using a pipe reactor.

Jan 1, 1977

By G. Barbery

"Particle composition distribution is an essential feature of materials processed by physical separation methods. The amenability to segregate a feed material in a concentrate and a tailings stream depends to a large extent on what is called usually the ""liberation"" of the various mineral phases that are present in an ore. In fact the energy consumed in crushing and grinding has the major justification of producing particles that are as close as possible to monominerallic. Monophasic particles are able to reveal physical differences in mineral properties that make their separation possible. For many years, various authors have insisted on the concept of liberation, without noting that, in practice, it can be a pure concept which does not lead to measurements or predictions. The present paper insists on the concept of particle composition distribution, in which the complete distribution is the information to be obtained, and not the ""liberation·· of various phases, just like for particle size distribution, the complete distribution is an objective commonly desired, and not one or two values representing the coarse or fine fraction.2. NOTATIONS-EQUATIONSFor the purpose of the paper, a particle will be characterized by its volume Vp, and its volumetric composition with respect to a mineral of interest, which will be given the notation ""O"". All the other minerals present will be called ""1"". This notation does not imply that the particles are biphasic, but that we are interested in the composition of particles with respect to one phase only. The volumetric composition will be given the sybol m:"

Jan 1, 1986

By F. Keller, E. H. Dix

The desirable high strength and hardness of the heat-treated strong aluminum alloys result from two distinct structural changes: (1) the formation of a solid, solution by heating at the required temperature for a sufficient period, and the substantial retention of this solid solution by rapidly quenching; (2) precipitation of particles of constituent and coalescence to a critical size to produce maximum strength and hardness. In alloys of the duralumin type, that is, alloys containing both copper and magnesium silicide precipitation takes place at normal atmospheric temperature, whereas in alloys containing copper without magnesium silicide or magnesium silicide without copper, maximum properties are obtained only after an accelerated aging treatment consisting of heating for 15 to 20 hr. at temperatures of about 150" C. The mechanical properties of these alloys subsequent to quenching but prior to aging are ideal for forming operations. Unfortunately, however, the alloys of the duralumin type age very rapidly during the first 24 hr. and aging is substantially complete after four days. For severe forming, such as the heading of rivets, it is desirable that this be accomplished within ½ hr. or at the most 2 hr. after quenching. Alloys containing magnesium silicide without copper also age at normal temperatures but the aging is less rapid and the material can be satisfactorily worked within several weeks after quenching. Some slight aging of alloys containing copper alone also takes place at room temperature but it is unimportant from the standpoint of workability. Any method of retarding the aging at room temperature of the duralumin type of alloys would be of considerable advantage in that the period during which the material could be worked successfully would be lengthened. For instance, in aircraft plants it is customary to supply the workmen with small lots of rivets that should be used within ½ hr . after heat treatment. Such procedure has the obvious disadvantage of being uneconomical, and furthermore there is always the possibility that the workmen would use the rivets after the time limit had expired, or the supply being depleted might use some that had not been heat-

Jan 1, 1931