Search Documents

By Robert A. Cortese, Carrie E. Lucci

Mine Safety and Health Administration (MSHA) regulations require underground coal mine operators to dust their mine corridors with an inert material to prevent coal dust explosions. The most commonly used material is pulverized limestone. Current practice to determine compliance with MSHA regulations requires the coal mine foreman or an MSHA inspector to collect samples of the deposited dust, a mixture of coal dust and limestone rock dust, for above ground laboratory analysis. To expedite this process, the U.S. Bureau of Mines has developed two instruments to facilitate the inspection and rock dusting processes, the explosibility meter and float dust deposition meter. The explosibility meter is a hand-held instrument which provides an in situ measurement of the explosible nature of homogeneous mine dust samples. The float dust deposition meter measures the mass loading density of the top layer of coal or limestone dust deposited on the mine floor during mining operations by the ventilation air. It may also be used to automate trickle rock dusting equipment. The operation of each device is based on the difference in the optical reflectance between the light limestone dust and the dark coal dust. The principal of the explosibility meter is based on the observation that, for a fixed coal volatility, the optical reflectance of dust mixtures is relatively constant at the limit of flammability, and independent of the coal dust particle size.

Jan 1, 1995

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950

By S. R. Clifford

Organic contaminants can be removed from river sediment using conventional flotation methods. Organic contamination in sediments is one of the most significant pollution problems facing the Great Lakes region. Using conventional flotation, the majority of the organic contamination can be collected in a concentrate, leaving a "clean" tailings. This provides a cost savings by reducing the amount of material requiring further treatment. The concentrate can then undergo additional flotation stages, or other contamination removal procedures, to further remove the organic contaminants.

Jan 1, 1994

This brief resume of events, transpiring in Mexico, culled from the daily New York newspapers, since the last Bulletin went to press, does not indicate any degree of improvements in the situation. GENERAL ALVAREZ COURTMARTIALED AND SHOT General Francisco Alvarez of the anti-Government forces was captured in the battle in which General Aureliano Blanquet, Minister of War in the Huerta Cabinet, was killed, and was sentenced by a courtmartial and shot in spite of a specific order of the Supreme Court in Mexico City that the execution should not take place. General Alvarez was a member of the staff of Felix Diaz, and was a veteran of the old regular army of Mexico. MEXICO WILL NOT RECOGNIZE MONROE DOCTRINE Failure of the Allied Powers to invite Mexico to participate in the conference of neutrals at Paris aroused President Carranza to bitter resentment, which was enhanced by the incorporation of recognition of the Monroe Doctrine in the covenant of the League of Nations without consultation with Mexico. Statements were issued by the Mexican Foreign Office disavowing adherence to the Monroe Doctrine and announcing the withdrawal of the Mexican representative in France. Carranza had been awaiting an opportunity to get his agent away from Paris for the real reason that he had been unable to secure recognition from either the French or the British Government. Mexico announces, says the New York Times editorially, that "she has not recognized and will not recognize the Monroe Doctrine." "Nobody has asked her to recognize the Monroe Doctrine," continues the editorial. "The enforcement of the principles enunciated by President Monroe does not depend upon Mexico, upon anybody's recognition or non-recognition. The countries concerned in the Monroe Doctrine are the United States on the one hand, and countries not of this hemisphere on the other."

Jan 6, 1919

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By Eugene Guccione

"Instead of just talking to ourselves we should inform the public of the grave problems that beset our profession and our industry." We've all heard and voiced that complaint at SME-AIME meetings; and if we were physicians, lawyers, pretzel retailers, or what-have-you, we'd hear and voice the same complaint at meetings of the American Medical Association, the Bar Association, the American Pretzel Institute, etc. Somehow we are all convinced or at least hope that if we could only, "get our message across to the public" (an extremely difficult and astronomically expensive proposition), everything would suddenly turn for the better. But would it? Hardly.

Jan 2, 1976

By Marshall K. I

THE problem of satisfactorily eliminating the fumes and dust which are unavoidably produced in various metallurgical and manufacturing industries is one which has received considerable attention in the past, and has been the subject of much investigation and research. The solution of this problem was urgently desired for two reasons, the principal one being the fact that a considerable percentage of the total process losses in many industries was represented by the commercial values of the fumes and dust that escaped from the stack.The other reason is that, in some instances, the emission of the matter is regarded as objectionable. Various methods have been designed with a view to solving the problem thus presented, and the latest development that has beendesigned is the process of electrostatic precipitation. Continued investigational and developmental work with this process has already demonstrated its applicability to many industries, and new uses to which the process can be put are being opened up. Its use is already widespread, and the economic success that has attended its application in most instances would indicate that its use will become more general in the future.It has proved its ability to treat gases over wide ranges of temperature, and has successfully handled various types of fumes whose chemical characteristics differ very considerably. In many processes it has now come to be regarded as standard equipment.HISTORY OF ELECTRICAL PRECIPITATIONThe first recorded observations on the influence of an electrified insulated wire on gases containing solid particles in suspension was made as early as 1824 by Hohlfeld, in Leipzig. He found that, if he electrified a wire hung in a bottle filled with smoke, the smoke cleared rapidly, and a deposit formed on the sides and bottom of the bottle.

Jan 1, 1923

By W. R. Finney

THE formation of scale in boilers and other industrial equipment, and the corrosion of such equipment, are closely related problems. Since in the petroleum industry these problems cover a very broad field, this paper has been confined to the effects of scale and corrosion on gas engines, compressors, pipes and fittings, used in plants extracting gasoline from natural gas, and the steps taken in arriving at a workable plan for combating these evils at the Midwest Refining Co.'s plants in the Salt Creek field, Wyoming. Eliminating, or at least minimizing, the many deleterious effects occasioned by the use of bad water in jackets and cooling systems of gas engines and compressors has been the subject of much study for many years but no generally accepted plan has been evolved. The problem was unusually difficult at Salt Creek, as the severe winters of Wyoming bring operating conditions quite different from those encountered in warmer states, and the water available was especially bad. While the conditioning of water to prevent scale and to lessen corrosion may not be a particularly difficult problem in plants in large industrial centers, it becomes much more difficult when attempted at plants remote from railroads and by men without previous experience to guide them. In fact this difficulty has been so great in the Wyoming oil fields that until comparatively recently it has been the practice to allow much equipment to be ruined rather than to attempt corrective measures. At the Midwest plants this problem was given attention first by the plant men and later by both plant men and laboratory staff. To the latter it was simply one of many problems which arise in connection with field and plant operations, which must be studied and, if possible, solved. Many mistakes were made during the course of this investigation, but since mistakes, properly interpreted, are of value in guiding one's steps aright, it is believed that a review of the different stages of development which have led up to the present method of handling this problem will prove of interest to the industry.

Jan 12, 1926

By Martin Hertzberg

In this Bureau of Mines report, the optical detection of fires and explosions is considered fundamentally. The measured spectral radiances from methane-air ignitions are compared with the background irradiances from stray and ambient sources, and with the spectral sensitivites of various sensors. The comparison naturally suggests the optimum spectral ranges and signal processing logic that can uniquely characterize the ignition event. Both ultraviolet (UV) and infrared (IR) are considered. Several alternate sensing methods are proposed and discussed. The development and testing of an IR system designed for use in ignition suppression devices in mines is described.

Jan 1, 1975

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

By A. McLean, L. Gao, Z. Shi, Y. D. Yang, K. Chattopadhyay, G. F. Zhang

Levitation melting of metals is one of the emerging applications of magnetic and electric fields in liquid metal refining. The varying magnetic field generates induced current inside the metal droplet and leads to the Joule heating effect and Lorentz force against gravity. This contactless process can avoid contamination from the crucible and can be used to produce high-purity materials. Visualization of the levitation melting process is difficult, and thus generally investigated by mathematical modeling. In the present study, a three-dimensional mathematical model of metal levitation was developed using finite element method for proper understanding of the levitation process. The effects of harmonic magnetic field frequency, coils power input, and sample size on levitation nickel droplet were investigated. Temporal evolution of temperature fields were predicted directly though the model. Levitation and balance condition of the droplet were investigated as well.

Jan 1, 2015

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Howard A. Smith

OF late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9† although two investigations have been made on copper alloys 10-11. That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut für Eisenforschung13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

By K. G. Sutterer, R. J. Sweigard, U. Graham, T. C. Hopkins

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1998

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calculations where the compliance limit of lbs SO2/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equations to blend to an SO2 content of 1.2 lbs SO2/million Btu, the excess sulfur for Coal A was defined as Sulfur excess% = 0.5 - 0.6*13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C[<] 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: •W is the total weight; •A, B and C are the fractional proportions of each potential blend stocks; •Sa, Sb and Sc represent the percent sulfur content of the blend stocks; •Ha, Hb and Hc represent the calorific content of the blend stocks in Btu/lb; and •H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1998

By Jr. Smith

Silver-gold ratios were studied at the Tayoltita epithermal vein deposit using channel sample, channel sample line, stope, ore body and vein sample populations. The ratios are highly variable among individual channel samples (25:1 to greater than 500:1) with both high and low values randomly distributed within ore bodies and veins. Whole vein ratios for the fourteen most important ore producing structures range from 44:1 to 105:1, and show zonal distribution relative to two small granitic stocks, low values closest to the intrusives. The zoned nature of the deposit suggests that the stocks, apophyses of an underlying batholith of Late Eocene age, were the heat engines which powered the hydrothermal system responsible for ore deposition.

Jan 1, 1978