Search Documents

E. P. Pfleider, University of Minnesota I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. R. H. Merrill, U. S. Bureau of Mines, Denver Federal Center The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability. G. A. Leonards, Purdue University I was interested in Mr. Lane's observations concerning the correspondence between rate of slide movement with rise of reservoir. Perhaps the most interesting feature is that the rate of movement at the time the rock slope failed was less than the rate at an earlier time when it did not fail. This is difficult to explain from current slope stability theory. K. S. Lane, U. S. Army Corps of Engineers I believe that reduced rate of movement is the result of the progressive type of failure, such as described by Patton and Deere. which occurs along the sliding surfaces. It is difficult to analytically define the progressive failure condition for inclusion in slope stability conditions, but its existence should be recognized in design. We should also realize that many apparently stable slopes undoubtedly contain overstressed regions. To design a slope with no overstressed region would be uneconomical and conservative. D. H. Deere I would pose the question-"What is the meaning of a factor of safety of one?" We were involved in the design of a large, irregularly shaped, underground cavity with an unsupported span of several hundreds of feet. Tests on rock specimens indicated a strength of 1300 lb per sq in. The RQD would have been between 90 to 100 percent indicating excellent structural continuity. In-situ stress determinations indicated an approximately hydrostatic state of stress at a level of 1400 lb per sq in. Calculation of stress concentrations at the walls indicated that the stresses there would be about 3000 to 4000 lb per sq in. Admittedly the rock is in a confined condition everywhere except at the very skin of the wall and the rock walls would thus on the average be somewhat stronger. Allowing for the effect of restraint the factor of safety was found to be less than 0.5 over a region several feet into the wall. Construction was started, using rockbolts only to support the walls. Failure around the immediate skin occurred after each

Jan 1, 1967

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By M. J. King

The Chino Smelter embarked on a program to reduce smelter emissions. Fugitive sulfur dioxide and particulate emissions were reduced by (i) removing the flash furnace settling chamber and (ii) installing a baghouse, to treat converter secondary emissions. Neutralization plant capacity was increased, to accommodate increased flow from the flash furnace off-gas cleaning system and to reduce costs.

Jan 1, 1998

Data about shipments in this county are more plentiful than in most others. Canal records, although not complete, are available for 1837-1840, 1856-1857, 1859 and 1864. The census figures, and those of the reports of the Secretary of Internal Affairs, are very evidently too .low. Local consumption within the county has always been large, mainly due to the Cambria Iron Company, and other manufacturing plants, in Johnstown; here a large coke supply was made from coal directly from the mines, neither coal or coke being handled by any outside transportation agency. All available data is shown in Table 35.

Jan 1, 1942

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By Robert B. Parsons

"Two recent decisions by the Canadian courts could reduce the taxes paid by many profitable mines in Canada. At a time when the mining sector is hurting from an ever increasing tax burden and soft prices, the results of two cases are welcome news. Mining companies are well advised to check prior years' tax returns in the context of these developments. IntroductionSince 1976, the income tax legislation has provided a reduced rate of tax for taxpayers engaged in the mining of mineral resources, through the mechanism of the ""resource allowance"". The deduction given for the resource allowance effectively reduces the federal rate of tax by one quarter on resource profits. In general terms, ""resource profits"" are defined to include a taxpayer's income from: the production and processing in Canada of ore to any stage that is not beyond the prime metal stage (or the pellet stage or its equivalent in the case of iron ore); and, royalties computed with reference to the amount of value of production from mining operations in Canada.In computing income from these sources, the taxpayer must deduct expenses that may reasonably be regarded as applicable to those sources, with the exception of expenditures for Canadian exploration and development or financing costs.As a result of the mechanics of the calculation of the resource allowance, one quickly realizes that the lower the expenses deducted from the resource profits, the higher the resource profits and consequently the higher the 25% resource allowance. The impact of the recent court cases is to narrow the range of expenses which are required to be deducted in the determination of the resource profits.The two cases are outlined below."

Jan 1, 1991

Gentlemen:-I herewith present a report on some of the more important activities of the Institute for the year 1921. The present incumbent took. over the active management of the Secretary's office on the first of July and his, work was facilitated, while becoming acquainted with the routine of the office, by the constant and., kindly assistance of the former, Secretary, Mr. Stoughton, during the following three months, and that no interruption occurred inn its regular and smooth operation is due to him and to the Assistant Secretary, who has always been ready to give the benefit of his experience and assistance. MINING AND METALLURGY Through the efforts of President Ludlow and the generous assistance of one of our members, coupled with the excellent work of Major Barbour, MINING AND METALLURGY has, during recent months, shown constant improvement, which could not have taken place, however, had it not been, for the support given by a number of our contributing members. We have every reason to feel encouraged with respect to the quality of the publication and its cost of production. For the year 1921, the net cost of MINING AND METALLURGY was about fifty cents per member, per annum. Occasional letters are received criticizing the Board for producing this publication, but they are more than offset by letters of approval. When the, full purpose of the publication is appreciated, criticism ceases. The elimination of MINING AND METALLURGY and reversion to free distribution of all papers to all members, whether desired or not, would mean such a heavy additional expense that the number of papers would have to be much curtailed. The generous cooperation of members in sending for only such papers as they particularly desired has saved, the Institute thousands of dollars. A plan is being worked out that will materially assist in securing a prompt distribution to members of all pamphlets dealing with subjects in which they are especially interested.

Jan 2, 1922

By P Joyce, A S. Ray, P S. Thomas, J Haggman

Climate change and global warming present a significant challenge as unsustainable levels of greenhouse gas emissions arising from human activities continue to be emitted. The cement industry is responsible for between five and ten per cent of annual world carbon dioxide emissions; most arising from the manufacture of Portland cement (PC). An effective way of reducing emissions is by incorporating supplementary cementitious materials (SCMs) as partial PC replacements. SCMs are silicate or aluminosilicate based pozzolanic materials which, in finely divided form, combine with water and calcium hydroxide (lime), liberated by cement hydration, to form compounds exhibiting cementitious properties. Pitchstone is such an aluminosilicate and has the potential to act as an effective pozzolan for partial replacement of PC. In North Queensland, Australia, a vast deposit of pitchstone is mined and processed for expandable perlite aggregate. During the classification stage of the excavated natural material, waste pitchstone fines (PF) less than 0.5 mm in size are generated. This study evaluates the waste PF as a viable, eco-friendly pozzolan for the partial replacement of PC. The reactivity of the PF is compared to fly ash (FA), using the pozzolanic compressive strength activity index (SAI) after seven, 28, and 91 days ageing at 20 per cent and 40 per cent PC substitutions. PF was found to be comparable to FA as a pozzolan at 20 per cent PC substitution at all ages tested. However, for the 40 per cent substitution blends significant strength was only achieved at 91 days ageing for the FA blend. The pozzolanic reactivity was also investigated using thermogravimetric analysis to determine the degree of free lime present after 91 days. In all cases where an SCM was added, the free lime was observed to be consumed with increasing age.

Jan 1, 2008

By Graylin R. K, dea T. R, O&apos

The Wolgan Seam of the Upper Permian IlIawarra Coal Measures of the Western Coalfield of New South Wales consists of high volatile, low sulphur, medium hard coking coal with high fluidity. This seam, 1·8-2·4m thick, in the Wolgan area, dips gently at 1°_20 ENE and lies at 160-440m below the deeply dissected surface of the western margin of the Blue Mountains plateau.A detailed study of the deposit has revealed that the Wolgan Seam consists of four main coal plies separated by three distinct stone bands. Each of these subunits is lenticular and displays individual physical, chemical and mineralogical characteristics which exhibit distinct spatial distribution patterns across the area. Most noticeable is the presence of long linear ESE-trending zones of low ash - high volatiles - high fixed carbon - high fluidity which delineate the major distributary pattern within the deltaic environment of coal formation.This seam contains some of the highest fluidity coal in the world.The Wolgan area, close to the western margin of the Sydney Basin, is characterized by:I. a regional, closely spaced, homogenous joint fracture pattern dominated by an orthogonal pair set trending 3400 and 0700, to which the face- and butt-cleat directions respectively of the Wolgan Seam are sub-parallel, and2. a more widely spaced, heterogenous, cross-cutting pattern of regional structural fractures. Zones of bad roof conditions are probably associated with these lineaments which are subvertical and trend in three majordirections, viz., 005°,035° and 115°.

Jan 1, 1980

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By E. D. Gardner

FIFTY years ago the Utah Copper enterprise at Bingham was just getting under way. An epic in metal mining was in the making. Throughout the West the bonanza deposits were approaching exhaustion and most ore still went direct to smelter. But concentrators were shortly to be constructed for treating milling grade ores, and most important, the pilot plant for the Utah Copper enterprise was being built that year at the mouth of Bingham Canyon. The same decade was to see development at the Inspiration mine in Arizona of the most important new mining method for 50 years to come—undercut block caving. Although the average grade of ore being mined has been declining for 50 years, and wage rates and prices of supplies have been greatly increased, the mining industry has continued to grow and to prosper. Technology has advanced to a point where minerals can be mined under the most severe conditions. The hardest rock can be drilled and broken and the heaviest ground handled. Large or small, an ore-body can be mined successfully, at any desired rate of production. It is possible to pump great volumes of water and to ventilate the most extensive workings; air conditioning has made practicable the mining of ore where the rock temperatures are beyond those that can be borne by man. Mining today in the U. S. is a huge earth-moving operation. In 1953 nearly 2 billion tons of material were mined for direct use or for processing. Stripping at open-cut mines totaled about 1.7 billion cu yd. Table I gives relative tonnages of the branches of the mineral industry in 1953. In addition to the solid materials moved, 350 million tons of petroleum and 340,000 tons of gas were produced in 1953. Fifteen million tons of salt and 5 million tons of liquid sulphur were pumped from wells. An appreciable amount of copper was recovered by leaching old mine workings and dumps. Total value of minerals produced in 1953 was $14.4 billion: oil and gas $7.6 billion, coal $2.6 billion, nonmetallics $2.4 billion, and metals $1.8 billion. Formidable problems face some branches of the industry today, especially pertaining to increased output tons per manshift. The time has come when these problems should be reappraised. With current wage rates, the industry no longer can afford to pay men to do manual labor. It should be recognized, also, that the miner is a skilled worker; efforts to promote the dignity of his calling and his pride of accomplishment have yielded beneficial results. Mineral deposits occur under widely varying conditions. In most instances the degree of support needed by the roof and walls is the deciding factor in selection of an underground mining method. The degree of support needed, in turn, is governed by natural physical characteristics of the ore and its enclosing rocks. Mine operators, of course, learn to judge ground by observation, and an experienced mine boss generally can anticipate what will happen following any given mining operation. A more scientific approach, however, would be advantageous in most cases. More should be known about the strength of the ore and the enclosing rocks, more about stresses set up in the ground when ore is removed, and more about the mechanics of moving ground. Better understanding would work both ways: first, favorable rock conditions could be fully utilized for more efficient mining, and second, hazards of rock falls could be minimized, loss of ore in mining reduced, and expenses caused by ground pressures and subsidence lowered. In general, mining comprises breaking the ore or rock in place, supporting the mine workings, and transporting the ore to the surface. This latter is a materials handling problem. Ventilation, of course, must be provided, and the mines must be kept free of water. Development work at some places is the most important cost item in extracting ore. Drilling and blasting remain the usual practice for breaking ore or rock from place except, of course, at block-caving mines. The drilling and blasting practice at a mine must fit the mining method. In laying out mining procedures attention is being given to

Jan 1, 1956

Jan 1, 1948

Inevitably the 'post-boom' era has changed the emphasis of many mining companies away from new project development and expansion to optimisation of existing operations. However, regardless of the project, high quality ore characterisation will remain of the utmost importance. In the case of new project development the need to understand the breakage characteristics will remain as important as it has always been. In optimisation projects, however, where it will be required to get the very best from existing comminution circuits, accurate geometallurgical modelling will take on an increasingly important role. However, these requirements, in both new development and optimisation projects, are likely to be at odds with budgets as these will be tight. Hence obtaining the best value for money will be essential. This paper discusses the elements that need to be satisfied for ore characterisation programs to be successful. Some of the issues covered will be: ore variability and sample selection, test precision, problems with the use of non-standard testing equipment, and the value of databases.

Jan 1, 2009

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Brian Hart, Zhe Chen, Liuyin Xia, Mana Pourdasht, Stamen Dimov

"Gold losses related to carbonaceous matter (CM) during processing are a significant problem in the gold processing industry. Inherent CM in gold ores can behave similarly to activated carbon in its ability to adsorb gold cyanide. This phenomenon is termed preg-robbing as the surface adsorbed gold cannot, for the most part, be recovered. Research has identified that gold adsorption by inherent CM is linked to the specific surface area, pore structure, degree of C disorder and surface functional groups. One of the strategies to inhibit CM preg-robbing prior to leaching is a chemical oxidation; a process linked to modification of the surface functionality. In this study, the variability in gold cyanide adsorption due to oxidation with different reagents has been investigated. Variability in gold cyanide adsorption by CM is examined in relation to structural and surface modifications using TOF-SIMS, XPS and Raman spectroscopy.INTRODUCTION A major obstacle for effective gold recovery during carbon in leach (CIL) or carbon in pulp (CIP) processes carbonaceous gold ores is the presence of carbonaceous matter (c-matter) which has the ability to adsorb, or preg-rob gold from the cyanide leach solution. It can be responsible for poor recoveries as the carbonaceous materials (CMs) within the ore competes with activated carbon used during the leaching and adsorption phase of processing (Cay, 2014). Preg-robbing capacity can vary significantly with mild preg-robbing ores showing absorption capacities of less than 1 g Au/t ore, while severe preg-robbing ores may have CM with the capacity to preg-rob more than 500 g Au/t ore (Dunne, 2007). Research by a number of groups have shown that the degree of C disorder has some influence on the ability of the carbonaceous material to adsorb Au(CN)2- (Miller et al, 2005, Helm et al, 2009, Hart et al, 2010). It is also apparent the adsorption characteristics of carbonaceous material is affected by changes in surface chemistry (Dimov, 2016). Various treatment including; flotation to remove the carbonaceous material (Wills, 2010), addition of surface blinding agents (for example kerosene) to passivate or blanket the carbon surfaces (Dimov, 2016), addition of strong adsorbents (eg. activated carbon or resin) to compete with the carbonaceous material and passivation or surface coating by oxidation (pressure, roasting, chlorination and biological oxidation), have been employed prior to leaching in an attempt to minimize the gold losses (Dunne, 2013)."

Jan 1, 2017

By Burton Atkinson, David Johnston

Evaluation of Ellenburger reservoirs in West Texas has been an uncertain matker at best because of the lack of cores and suitable core-analysis method. Large amounts of oil arc produced from sections from which sample cuttings are obtained that contain litile porosity and no oil saturation. It has long been realized that the formation in some areas contained numerous fractures and solulion cavities that probably contained the major part of the oil present but the magnitude of the porous system conltaining oil has been unknown. Diamond coring cquipmene, used in the mining industry lor many years, has been developed for oil-field use to obtain high core recovery in fractured dolomite that is not possible with conventional coring equipment. A 36ft section of the core recovered from a fractured Ellenburger reseivoir waS analyzed by a unique but simple method to obtain the first defmite evaluation of one section of the producing formation. The cores and the method of analysis used are described and the results arc discussed in some detail. Discussion The first successful known analyses of cores recovered from the Ellenburger formation in the Permian Basin area were made on cores recovered with the use of diamond core heads. Conventionul coring methods previously used have had lour core recovery and standard methods of analysis have proved to be inadequate for evaluation of those cores that were recovered. Core Descriplion The Ellenburger formation to be dis cussed was cored using diamond core heads and oil-base drilling fluid. Of the total 103 ft cored to a depth of 8893 ft in the Ellenburger, 99 ft or 96 pct was recovered. The dolomite cores were described as gray to white, crystalline to coarscIy crystalline, with chert and calcite inclusions. Occasional shale partings ? to ¼ in. in width were noted. A small amount of green clay was found in some of the coarsely crystalline material. So intergranular porosity was found by inspection in any of the cores. The core urns highly fractured over most of its length with not more than two continuous feet that failed to contain fractures. The fractures Were nearly vertical and varied in width from those harely visible to as much as one millimeter. Scattered solution voids, or vugs, as large as 3 cm in diameter occurred in association with same •a

Jan 1, 1949

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.' It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911