Search Documents

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003

By L. H. Wolfe, J. O. Thieme

The tensile and shear strengths of frozen soil and the compressive strengths of ice and frozen soil were measured These tests showed that the strength of ice and of frozen soil increased as the temperature was decreased. A method is presented for the measurement of thermal conductivity and specific heat of earth and ice. Using the parameters thermal conductivity, specific heat and density, the thermal diffusivity was calculated. Results of thermal property tests establish water as the major variable contributing to thermal property values. INTRODUCTION During the last few years, a considerable interest has developed in underground storage of cryogenic liquids such as liquid natural gas. Because of its economy and safety, underground storage is being used. Before underground caverns could be seriously considered, however, the strength and thermal characteristics of the soil had to be obtained. Methods are presented herein for measuring tensile, compressive and shear strengths, specific heats and thermal conductivities. The tests were performed on two soils at temperatures from ambient to -195C. Because it is difficult to find data in the literature that pertain to a particular soil, ice was used to evaluate some of the experimental procedures. Some of our ice data are compared to the published values. PHYSICAI, PROPERTIES SOIL SELECTION AND SAMPLE PREPARATIONS The physical and thermal tests were performed on recompacted samples of two typical soils that might be encountered in underground caverns: a gray, fire clay that had been pulverized and mixed with water into a pliable mud; and a brown, sandy silt that was dug from a dry river bank and subsequent1y mixed with tap water. The moisture content of the test specimens was 17 to 22 per cent (based on the wet weight of the soil). This amount of water nearly saturated the silt, but the clay was well below the saturation point. The soils are partially described by the sieve analyses (Fig. 1) which show the particle size distribution of the coarser than 44 micron portion of the soils. The curves also show that approximately 75 per cent of the clay and 20 per cent of the silt are finer than 44 microns. The particle size seems to affect some of the physical properties, and the finer than 44 micron portion is important in the thermal conductivity test. Physical specimens were cut with a bandsaw from frozen blocks of the soil. The specimens were then sanded and kept frozen until after they were tested. They were stored at the approximate test temperature for several hours. Then, to equilibrate the samples to the test temperature, they were stored at the temperature at least an hour before they were tested. TEST EQUIPMENT An Instron, which is a constant speed gear-driven instrument, applied force to the samples and drew stress-strain plots of the test. All of the samples were strained at 0.02 in./min. All of the physical tests were conducted in a temperature cabinet that controlled the temperature to 1C. TENSILE STRENGTH Briquette or "dog-bone" shaped tensile specimens were pulled with suitably shaped jaws. This shape of specimen, which is usually used for tensile tests of concrete, is satisfactory for testing frozen soils except that the samples tend to

Jan 1, 1965

By B. Dubreuil, J. -M. Lalancette, D. Lemieux, C. Chouinard

The extraction of gold and silver has been examined via the use of mixed halogens: chlorine and bromine. The reaction was performed in a brine of sodium chloride with a small amount of sodium bromide at 40-50°C, in an atmosphere of chlorine, at atmospheric pressure. The process takes advantage of the very high reactivity of bromine towards gold, while the higher oxidation capacity of chlorine leads to gold chloride as end product with recycling of bromine. Fast reaction rates are observed along with gold recovery at the level of 95%. Chlorine-consuming common elements are removed prior to chlorination.

Jan 1, 2011

By I. Melik-Gaykazov, N. N. Melnikov, V. A. Fokin, S. P. Reshetnyak

Kola Mining Institute has been carrying out investigations of the possibility to steepen the walls of the Kovdor open pit with the design depth of 600 m. Steeping (up to 60°) wall angles is done by double height (24 and 30 m) benches with vertical slopes. One of the safety factors of mining with such walls is choosing the width of the safety berms preventing against rock falling from the slopes into the pit working area. The test on rock falling from 24 m benches has shown that vertical slopes are not more dangerous compared to the inclined(60-75°) ones.

Jan 1, 2003

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.' The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.' Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low' used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By Carl Beal

Introduction. DURING the latter part of 1915 and the first half of 1916, the writer held the position of geologist in connection with the conservation work instituted by the U. S. Bureau of Mines, on oil and gas land belonging to the Indians of the Five Civilized Tribes in Oklahoma. The duty of the geologist was to correlate formations containing oil, gas,-and water, and to determine the relations of these substances in the different formations so that the conservation agents might carry on their work most intelligently. On account of the rapid development of the Cushing field, which lies in the western part of the Creek Nation, much work was clone there by the inspection force. In the course of the geologic studies a large amount of information was collected, which, on analysis, has disclosed some interesting facts worthy of publication. The report, of which the following remarks are an abstract, has been prepared and submitted to the U. S. Geological Survey for publication. This report is now (June, 1917) in the press and will doubtless be issued in a few weeks. Methods Used In addition to the structure maps showing the folding of the Pawhuska limestone, which crops out in several places in the Coshing field, separate structure maps of the three most important productive sands-the Layton (Fig. 2), Wheeler, and Bartlesville-have been prepared. These structure maps, were prepared by obtaining the logs of nearly all the wells

Jan 8, 1917

By W. J. Travers

SEVERAL new procedures for completing oil wells have been developed in recent years. Each method when used where properly applicable promises to be a definite aid to operators in lowering development or operating costs, or in developing the full potentialities of the oil well. Multiple-zone completions are now frequently used, in contrast to the older practice of setting a solid water string over each zone to be produced. Gravel packing in unconsolidated formations often prevents sand troubles formerly experienced where a conventional perforated liner was used. Light-weight bentonitic clay muds and oil-base drilling fluids are definite steps toward eliminating mudding damage, which occurs when heavy rotary mud is used. Since in each case the new procedure developed is an alternate of older conventional methods, a problem of selection is presented. The purpose of this paper is to suggest methods of arriving at these choices and to present practical observations that may be of aid in their application.

Jan 1, 1942

By E. J. Duggan

It is a coincidence that the two plants in this country for treating copper ores by ammonia leaching came into existence at almost the same time, that of the Kennecott Copper Corporation at Kennecott, Alaska, in March, 1916, and that of the Calumet & Hecla Mining Co. in July of the same year. The success of both from their very beginning attests the merits of the process under widely different sets of conditions. As would be expected, in the time they have been operating these two pioneers in this field have greatly perfected their methods and improved their technic. The early difficulties inevitably encountered in undertakings of this nature have been largely surmounted and the process may now be considered to be well seasoned and matured. There have been no other commercial plants built in this country and but one elsewhere, the Bwana M'Kubwa in Northern Rhodesia, for the reason that this method of treatment may be employed on comparatively few ores. However, it has certain advantages, some of which are inherent to sand leaching processes generally and some to ammonia leaching in particular. Among these may be enumerated: (1) the avoidance of fine grinding; (2) the small amount of water required; (4) a high-grade product; (5) little likelihood of deleterious gangue constituents and fouling of solutions. It is true that great progress has been made in recent years in the flotation of the ores that come within the province of ammonia leaching. Nevertheless ammonia leaching has its possibilities and these may be overlooked in the present tendency toward the use of flotation for all ores. Probably the chief requisite to its further extension to suitable ores will be a cheap source of steam. Ammonia, the only reagent required, is unlimited in supply, readily transported and the price that is likely to obtain in the future should not make its cost at all onerous. Choice of Method for Kennecott Ores The Kennecott ores are typical limestone replacement deposits. The milling ores have a copper content of approximately 8 per cent in a limestone dolomite gangue. About half the copper occurs as sulfide, mostly chalcocite with some covellite, and the remainder in the form of the two carbonates, malachite and azurite. A comparatively coarse grind followed

Jan 1, 1934

By A. J. Weinig

THE Liberty Bell cyanide precipitate is unique in that it is apt to vary widely in composition in the course of very short, periods of time, and a method of refining and melting that would prove highly satisfactory at one cleanup would yield almost an hopeless "mess" it a second. Table I gives a general conception of the wide range in grade and composition of those raw precipitates. It is evident that no one standard flux could be expected to produce a high-grade bullion with such a widely variable precipitate, and that any method of treatment with acid requires most careful consideration. Refining by Acids Naturally, our first efforts to improve our precipitates were directed along the lines of acid treatment. Table II embodies the results of careful sampling and analysis of one cleanup at the time when wet refining reached its maximum development at this mill. We have now discarded all methods of wet refining, successfully replacing them by amore scientific method of flux calculation described herein, but it is believed that a general description of this wet refining is warranted as it throws some interesting side lights on acid refining in general.

Jan 3, 1916

By H. D. Outmans

The paper presents a theoretical approach to the drilling problem based on rock mechanics and drilling fluid hydraulics at the bottom of the hole. The volume of the fractured rock around the vevtically penetrating bit tooth is expressed as a function of the tooth pressure, included tooth angle, drilling fluid pressure and formation characteristics on the assumption that fracturing is preceded by plastic flow. This assumption is verified by comparing the stress-strain state in the rock around the tooth to that in equivalent tri-axial compression tests described in the literature. An expression similar to the above is derived for the tooth penetration in the cuttings which have been retrained at the bottom. Combination of these two expressions leads to a relation between depth of tooth penetration in the virgin rock, the amount of cuttings retained and the other variables. By relating the cutting volume to the drilling rate, the hydraulic bit horsepower and the drilling fluid pressure, it is possible to arrive at formulas which express the drilling rate for viscous or turbulent flow at the cutting surface, for instant clearance, for retained cuttings, or for false tooth foundering as functions of such variables as the drilling fluid pressure, hydraulic horsepower at the bit, rotary speed and bit weight. Plotting the results as drilling curves and comparing them to published field and laboratory data justify the conclusion that the drilling model presented in this paper approximates the actual mechanism. The drilling curves serve to explain some characteristic features of the rotary drilling operation, and the equations may be used for numerical evaluation of the effect of changes in the magnitude of some of the variables on the drilling rate. INTRODUCTION Published laboratory data have established that consistent and relatively simple relations exist between the drilling rate and any one of the important variables. For instance, the drilling rate usually increases at an increasing rate with the bit weight. It increases at a decreasing rate with the rotary speed, decreases at a decreasing rate with increased drilling fluid pressure and plots as an S-shaped curve against the hydraulic horsepower at the bit. This relative simplicity seems difficult to understand considering that the drilling mechanism is a continuous process of generation and removal of innumerable individual cuttings, under different conditions for each. On the other hand, the drilling rate (although determined by this complicated process) only expresses the average rate at which cuttings are produced and cleared away. Ignorance of the drilling mechanism as far as individual cuttings are concerned, therefore, does not exclude the possibility of arriving at a concept of the drilling rate provided the mechanism is properly evaluated for the average cutting. It then may be concluded from the first sentence that this concept also should be rather simple in its final form, although not necessarily in its derivation. Two aspects of the drilling mechanism are difficult to evaluate — (1) the effect a penetrating drilling fluid has on the stresses around a bit tooth entering the formation and (2) the volume of rock fractured by a penetrating tooth which moves both vertically and horizontally. Thus, the scope of this paper has been limited to an evaluation of the drilling mechanism in formations which have a low permeability and are drilled with hard-formation bits. In the following sections, the drilling mechanism is analyzed in three steps. First, the effect of tooth pressure on the volume of fractured rock around the tooth is evaluated, assuming initially that the bottom of the hole is free of cuttings and, then, determining the effect of a layer of these cuttings. In the second section, the thickness of this layer is related to the drilling rate and the chip clearance time, and the latter to the hydraulic horsepower at the bit under conditions of laminar and viscous flow at the cutting surface. In the third section. the previous results are combined with the rotary speed into drilling equations which are then plotted and compared to experimental drilling curves. This section also contains some numerical examples of drilling rate computations. Some mathematical details are given in the appendixes. Finally, it should be mentioned that, although some drilling equations are already available, these equations (with the exception of one' which attempts to relate drilling rate to drilling fluid pressure) are all mathematical expressions for observed laboratory data; none considers the effect of delayed drill-cutting removal, an essential feature of the drilling mechanism.

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors' experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Carl Trischka

During fifty-three years of mining operations in the Warren mining district, the mineralization has been found to cover an area roughly 2 miles long by 155 miles wide. Ore extraction from the richer portions of this area has been closely followed by surface subsidence. At the western end of the district, where the ore outcrops at the surface and oxidation is more complete over a wide area, intense surface disturbance is visible in the form of closely spaced open cracks and escarpments. As work has progressed toward the east, more unoxidized ore-bodies have been found and mining has been at increasing depth, for which reasons surface subsidence is less intense and subsidence blocks become larger and in general are bounded by open cracks, which persist over long distances. There may also be traced on the surface what appears to be a boundary crack, running in a northwest-southeast direction, marking the present southerly limit of subsidence of the district as a whole. It is not completely developed, and has not as yet appeared over the very deep mining operations in the extreme easterly portion of the district. Check surveys show that vertical and horizontal dislocation is still taking place. All of the various mining operations, including open-pit work in porphyry ore and underground mining of limestone replacement and porphyry ores, have had their influence in disturbing the surface. As these influences frequently overlap, and because the surface disturbance is continuous over practically all ore occurrences, it is virtually impossible to choose an area sufficiently isolated to ascribe the amount of subsidence to any definite volume of ore removed. After due consideration of all factors, there has been selected for discussion an area 1400 ft. long by 1200 ft. wide, which will be referred to as the Queen Hill block. It is bounded on all four sides by faults, which tend to limit subsidence disturbance to that caused by ore mined from within the block, and likewise to prevent subsidence cracks due to mining outside of the block from entering the area.

Jan 1, 1934

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977

A predicted increase in aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Browncoal char, with a lower ash content and with an elemental purity similar to petroleum coke, was produced by leaching in hydrochloric acid, washing with water, and charring at 1,150°C. The cost of processing is estimated tobe competitive with petroleum coke.Without further processing the bulk density and real density were undesirably low, but by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value andthe particle density was improved to 92 per cent of the density of petroleum coke by water displacement or 75 per cent by mercury displacement.Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char, and from petroleum coke alone, all bonded with coal tar pitch.The electrodes were tested for the usual physical properties and were evaluated for performance in a laboratory size alumina reduction cell.Electrodes based on brown coal char alone were found to be inferior in physical properties and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity, and carbon consumptionon a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 per cent better electrical current efficiency than the electrodes based on petroleum,coke alone.It is suggested that larger scale tests are warranted.

Jan 1, 1971

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J. J. Quinn

Several mineral flotation plants utilize process water with high soluble salt content. The processing of semi-soluble minerals, the use of recycle streams, sea or well water give rise to this situation. It is unclear as to the overall effect on flotation response though there does seem to be evidence of bubble size reduction, increased froth stability and reduced reagent dosage. The present work aims to quantify the effects of salts present in process water on gas dispersion (bubble size and gas holdup) and froth properties. The salts examined were NaCI, CaCl2, Na2SO4, Na2S2O3 and Al2(SO4)3. Tests were conducted to determine the effects of salt type and concentration on gas holdup and bubble size distribution. The salts containing multivalent ions had a greater impact than the monovalent ions, in keeping with the literature. A relationship between gas holdup and ionic strength was established. The concentration of frother (methyl isobutyl carbinol, MIBC) giving equivalent gas holdup was determined. The effect of salt and frother combinations was also explored.Proposed mechanisms for coalescence inhibition in salt solutions are briefly reviewed in light of the current findings.

Jan 1, 2006