Search Documents

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By Alfred C. Maevis

On October 27, 1972, ground was broken for the first section of the Second Avenue Subway, a two track underground rail system that was to extend from the south end of Manhattan at Broad Street, north to the Harlem River at 126th Street, a distance of eight miles. This ground breaking was the culmination of 67 years of planning for an east side subway in Manhattan. Following the successful opening of New York City's first subway on October 1904 there was a mass planning for additional subways throughout the City. In 1905 approval was requested of the Board of Estimate for a First Avenue route and Third Avenue route. The Third Avenue route was approved but when action was not taken to start construction, the approval in accordance with the conditions under which it was given was withdrawn. Further reports and plans for an east side subway, usually to be constructed on Third Avenue, were issued in 1920, in 1922, in 1924, etc. Those of us who had worked on the Sixth and Eighth Avenue subways in the thirites and early forties left to join the armed services of World War II in the expectation that we would return and start work on designing and constructing that east side subway. The reason that much of the thrust in those years was to construct on Third Avenue was that there was a Third Avenue "EL" and business interests of the City were in favor of its demolition. This demolition was accomplished in 1955 so one of the incentives to construct on Third Avenue was removed; but an east side subway was always part of the master plan of the City.

Jan 1, 1976

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author's reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer's understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author's bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan's motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By H. Ries

INTRODUCTION OF the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which results in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.1 There appears to he a difference of opinion, however, regarding the temperature at which it is formed. Thus. Klein2 notes that sillimanite forms only above. 1300° C., while Mellor claims that it can develop below 1200° C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mellor's, the temperature rose from 800° to 1180° in 24 hrs., and occupied the same time in cooling back to 800°.

Jan 9, 1917

By J. T. Liu

Packing in a flotation column is one way to increase separation efficiency and effective descending flotation-column height. In this paper, the difference between filling packing and sieve packing is described, and the flaws of filling packing in flotation columns in industrial application are pointed out. A change of flotation process and its effect on flotation results are reported. Based on sieve-plate filling, a high-efficiency mixed packing mode consisting of screen-plate packing and honeycomb-tube packing has been proposed, with the packing mode optimized in the cyclonic static microbubble flotation column in the separation zone. In the mixed packing mode, the honeycomb tubes are used to reduce the vortex effect at the base of the column and weaken the radial dispersion of jetting bubbles, and the sieve plates are used to comminute bubbles in the separation zone, to lengthen the bubble migration path, and to stabilize the foam layer. The superiority of honeycomb-tube packing is analyzed using bubble-particle collision theory, and the dynamic equations of collision probability are derived. The role of mixed packing in guaranteeing mineral recovery is analyzed by the axial dispersion method, and a dimensionless axial dispersion model is derived. When a high-turbulence flow is maintained, a static separation environment is formed in which secondary mineral processing is rendered more effective. In this way, a nonlinear separation environment is formed in the flotation column. Finally, mixed packing was applied in an industrial test. A large vortex developed at the base of the column. It was observed that the bubbles in the radial flow were homogeneously dispersed, the residence time of the pulp was prolonged, and the froth layer became thick and stable. Based on the test data, it was found that the sieve packing has the potential to yield a product of approximately 25.83% copper concentration with 91.78% recovery from a feed concentration of approximately 0.727%. If mixed packing were used, the product concentration could be further increased to 27.60% from a feed of approximately 0.739% concentration with 93.38% recovery.

Jan 1, 2014

By Arthur F. Wendt

In the manufacture of charcoal-blooms, washing or cleansing of the ore from adhering gangue has been practiced for many years. A sluice-box is even to-day used for that purpose in the Southern Appalachian Mountains. For the Lake Champlain bloomaries hard magnetic ores are crushed with stamps and then sluiced or jigged in hand-jigs. The stamps used in the Lake Champlain region are of the most primitive kind. They consist of a trip-hammer, dropping on a perforated cast-iron plate, through which the crushed ore escapes. Only friable rock can thus be successfully treated. To render the raw ore friable, a calcining or burning in piles on a bed of cordwood is resorted to. An expense of 35 cents per ton of crude rock treated is thus incurred. The crushed ore is shovelled or otherwise fed into jigs without previous sizing, except such as is incidental to crushing through the perforated bottom of the stamping-machine. In jigging this ore, it is allowed to pass through the bedding into the "hutch." The tailings are scraped off and wasted. They contain a large percentage of fine ore. In many instances, this is regained by subsequent sluicing. Such was the condition of the industry, when the writer's attention was first called to it in 1882. No attempt had been made to introduce into thiS branch of ore-dressing the notable improvements adopted in concentrating the ores of other metals. The result of the writer's investigations was the building in 1882 of the "Crown Point Separator." At the Crown Point Mines, N. Y., lean ore unfit for the blastfurnace (containing less than 331/3 per cent. of iron), was concentrated and used in the bloomary connected with the mines. The ore was burned here as elsewhere, and treated as described. The plant designed by the writer for Crown Point, is nearly a counterpart of that since erected by Messrs. Copeland and Bacon, contractors, for the Theal mine, Putnam County, New York, which is illustrated by the accompanying plate. The only difference is in

Jan 1, 1885

By A. C. Lawrence, K. F. Mauer

Human factors in stope productivity -a field experiment by K. F. MAUER, M.A. (Visitor), and A. C. LAWRENCE, B.Econ., D.Com. (Member) An experiment in which three human variables were manipulated in eight stopes was conducted in a gold mine over a period of roughly six months. The three variables, which each had two levels, concerned the degree of movement from gangs, the quality of the Bantu production supervisors, and the extent to which gangs were composed of a single ethnic group (Malawians). Time was included as a variable with three levels in the analysis of the findings. On the average, stable gangs produced 12 per cent more than gangs with a high percentage of transfers, gangs with better production supervisors were more successful by nearly 9 per cent than those with poorer production supervisors, and homogeneous gangs were more productive than heterogeneous ones by as much as 15 per cent. In addition, it was found that a number of the variables exercised a joint influence on stope productivity and that the effects of the variables were accentuated by the len gth of time they had been in operation. V

Jan 10, 1973

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By Gordon] [Reavis

Halliburton Services and Brown & Root have developed a unique foundation system that blends oilfield and construction technologies to construct deep foundations which offer significant advantages across a variety of soil profiles. This highly efficient system is being developed to meet the construction industry's needs into the 21st Century. Based on a concept initially introduced to Halliburton Services by V.L. Schellhorn in 1987, Halliburton combined their existing cement slurry mixing and pumping technology with oilfield drilling practices and a new tool design to field test the viability of the concept. Results looked encouraging, and Halliburton asked it's sister company, Brown & Root to evaluate and further develop the process. With Brown & Root's knowledge of the construction industry, the original concept has developed into a viable and efficient foundation construction system.

Jan 1, 1993

By C. S. Trewin

ZINC, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be determined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent. lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. ROLLED ZINC Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

Jan 1, 1928

By Morrison RD, Simmons CJ

A bewildering array of process control instrumentation is currently available for mineral processing plants. For sequencing control, special purpose microprocessors or the process control computer can be used. Where continuous control is required, then the choice is between pneumatic controllers, electronic controllers, shared display micro- processor systems and direct digital control. The benefits of each system are discussed and the advantages of using direct digital control in mineral processing plants are outlined. The factors which need to be considered when selecting control systems for new plants are listed. Instrumentation systems designed by Fluor Australia are used as case studies to illustrate the selection process. For established plants, conversion to direct digital can be advantageous, and case studies are given. However, replacement of existing systems requires justification based on a productivity improvement which will allow the control equipment to be paid for within a specific time period. Productivity improve- ments maybe assessed in terms of increased

Jan 1, 1978

By Rudolf E. Greuer

Modeling a mine ventilation system is a formidable mathematical problem requiring the solution of twice as many equations as there are airways with half of these being quadratic equations. The addition of a mine fire to the problem adds many more complexities. The U.S. Bureau of Mines and Michigan Technological University attacked this problem in stages. During the 1970's and 80's, a series of computer simulation programs were developed which offered progressively increasing levels of modeling capability and accuracy. The current version of this software, MFIRE 2.0, was released in 1993. This programs provides for full dynamic state mass flow-based modeling of a mine ventilation system, and includes natural ventilation, mechanical ventilation, air reversals and recirculation, methane and fire contaminant spread, and moisture condensation and evaporation in the mass flow and heat exchange calculations. This program is a useful tool for routine ventilation planning and can significantly improve mine safety by enabling detailed quantitative analysis for mine emergency preplanning. This paper reviews the evolution of the MFIRE program from its infancy as a simple digital network simulator replacing analog computers to the present version.

Jan 1, 1994

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By Brad Wells, Wayne Bull, Wayne Dickinson

"Antiscalants were evaluated for control of calcium carbonate (CaCO3) in gold processing applications. Under severely supersaturated conditions, 100 percent inhibition was achieved with 30 ppm antiscalant. Laboratory and field testing established that an antiscalant could both inhibit scale buildup and remove an estimated 0.5 kg/m2 per annum of pre-existing scale. A program was developed to control CaCO3 at a gold mill experiencing severe scale buildup. Annual accumulation of as much as 3 cm of scale in process piping was reduced to unmeasureable levels when 10 ppm antiscalant was applied. No scale-related upsets in mill operation occurred during a five-month trial period.INTRODUCTION Inorganic mineral scale is a crystalline deposit that forms when dissolved mineral constituents exceed the solubility of the respective mineral phase. Formation of mineral scale adversely affects a wide range of industries and is of particular interest in mining and metals processing. Scale affects numerous stages of metal extraction processes. Restricted flow in piping, nozzles, valves, screens, pumps and other components used to transport mineral slurries, metal concentrates, and tailings as well as scale in millwater and thickener overflow circuits are primary concerns (Alfano & Boffardi, 1994). Heap leaching, comminuation, flotation, vat leaching, carbon adsorption, and heat exchangers as well as oxidation steps used in processing sulfidic ores are among key unit operations that may be adversely affected (Simmons & Gathje, 2003). Antiscalant chemicals are designed to prevent formation and growth of mineral scales such as CaCO3. These chemicals, which include two primary classes – phosphonates and anionic carboxylate polymers and copolymers - are added to the gold processing stream at low parts-per-million (ppm) concentrations to interfere with nucleation and growth of scale forming crystals and to disperse fine particulate material. Application points may be located throughout the gold extraction process. Evaluation of the performance of antiscalants plays a critical role in determining the best product for a specific application. Performance evaluations include laboratory testing, pilot scale studies, in-plant trials, and ongoing performance monitoring during mill operation."

Jan 1, 2014

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By Jennifer Ward

The primary objective of this paper is to establish how a low cost, high definition (HD) camera can allow for easy sustainable recordings of blasting operations. The subsequent analysis of each video can be utilized to monitor what type of performance was achieved and aids in improving blasting performance.

Jan 1, 2015

The reliable estimation of ore reserves in mineral sand deposits depends on drilling methods and assay techniques that have been specially developed within the industry. Improvement of these techniques is a continuing process, as variations within and between deposits are highlighted during the actual mining operation. Constant monitoring of metallurgical losses along with mineral production allows comparison of mineral tonnages accounted for by mining, with original calculated reserves. A review of ore reserves in the Jerusalem Creek field from scout drilling in the sixties, through mining in the seventies, shows the progression from understatement prior to mining, to the present when more than two thirds of the reserves have been depleted.

Jan 1, 1979

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987