Search Documents

By Noreen D

At Bougainville Copper Limited comparison testwork was conducted between "horizontal" cycloning and conventional vertical cycloning. Horizontal cycloning reduces circulating load and allows increased ball mill throughput. Cyclone efficiency is the same or better as a result of the reduction of fines short-circuiting to the underflow. Operationally, horizontal cyclones are less likely to suffer from blocked spigots and high cyclone feed pump sump levels. Cyclone feed pumping power is reduced. High horizontal cyclone underflow density provides the option to optimise grind by manipulating water addition to the ball mill feed.

Jan 1, 1988

By P. M. Sandgren, H. Al-Dabbagh

Saudi Company for Precious Metals (SCPM) is jointly owned by the Saudi Arabian state organization Petromin (The General Petroleium & Mineral Organization) and Boliden of Sweden. The company operates the Sukhaybarat gold mine in the Saudi Arabian desert and produces some 80,000 ounces of gold per year by agitation and heap leaching. The discovery, development, and operation of this mine is a success story. After the first drill hole intercepted a gold mineralization in 1983, it took the partners only 8 years to delineate the ore reserve, locate water sources, prepare pre-and final feasibility studies, obtain permits, design, and construct the facilities. Sukhaybarat, which is an open pit mine, started off with a carbon-in-leach agitation plant only, but a heap leach facility was added in the beginning of 1995. Since start of operation in the middle of 1991, a total of 300,000 ounces of gold has been produced in the first four years of operation at a very competitive cost.

Jan 1, 1996

By Feebrey CA, Duncan RA

The Ebor Volcano in northeastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19-20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2-19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (-48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at -19.0-19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichment of SiO2, F,FeO/MgO, alkalies and HFSE.

Jan 1, 1995

Jan 1, 1886

By Yap Chu-Phay

ALTHOUGH chronologically, the Sb-Bi system was the first one studied by the writer, the theoretical basis of the equations used in this paper is fully discussed in the writer's paper on the iron-carbon system,1 because he believed that many would be more interested in the iron-carbon alloys. He suggests, therefore, that the reader consult that paper to familiarize himself with the theoretical aspect of the thermodynamic treatment outlined herein. This paper is divided into two parts: Part I deals with the Sb-Bi system and Part II deals with the lead-rich side of the Sb-Pb system. Although the former system has not much practical interest now, it has great theoretical interest in that it, is the one system that for a long time was thought to have (and under specific conditions still has) an anomalous solidus, which no amount of physical investigation could adequately account -for. The latter system of course, is particularly interesting in the lead-rich end. It will be shown that the thermodynamic method is capable of predicting reliably the equilibrium position of the solidus, and thus acts as a check on the experimentally derived solidus.

Jan 1, 1931

By E. A. G. Colls

Discusses corrosion in Trail chemical plants producing ammonia, sulphuric, nitric and phosphoric acids, ammonium phosphates, sulphate and nitrate, together with miscellaneous allied material problems and their solution using erosion or corrosion proof materials. Conclusion, that for work of this nature, most costly material may well be cheapest in the long run.

Jan 4, 1950

By Ennis P. C

The Mt Keith ultramafic intrusive extends for about 200 kilometres from Agnew in the south to Wiluna in the north. It forms the host for a number of nickel sulphide orebodies including Mt Keith and Honeymoon Well. Long fibre minerals are associated with the orebodies. The presence of these minerals impacts on the issue of tailings disposal from several standpoints, particularly the slurry beaching properties and dust generation from dry beaches. Central thickened discharge (CTD) is an innovative method of tailings disposal that involves stacking tailings in a low conical hill instead of storing them in cells. In appropriate circumstances this leads to savings in capital costs and operating expenditure. The method was introduced to Australia in 1981, and is currently employed at four operating mines, Elura and Peak Gold, both at Cobar in NSW, McArthur River in the Northern Territory, and Union Reefs near Pine Creek, also in the Northern Territory. It is the proposed method for Century Zinc and Ernest Henry, both in Queensland. The paper describes laboratory test work and design parameters for the application of the method to tailings disposal at Honeymoon Well and compares them with comparable data for other CTD systems. Of particular relevance for design purposes are beach slope, density, and water recovery. Wind tunnel tests were conducted on the Honeymoon Well tailings samples to investigate dust generation from the dry beach surface and it was concluded that dust generation from an undisturbed beach would not occur because of crusting.

Jan 1, 1996

Structural analyses of oriented bore core sections from the West Wallsend No.2 Colliery Holding together with investigations in adjac- ent collieries and on the surface delineated structural phenomena. The rocks examined are anisotropic due to strongly developed bedding planes and the presence of penetrative joint planes. Joints, in this context, are regarded as mechanical discontinuities, they are genetically identif- ied wherever possible and their spatial attit- udes are determined and geometrically related to the regional structure. Identifiable anisotropies in the roof- and floor-strata of the Borehole Seam render favour- able mining directions for longwall and bord and pillar layouts.

Jan 1, 1972

THE translators wish to record their appreciation of the help given by many individuals with whom they have discussed various details of the work. They are particularly indebted to Mrs. Anne Noble McKeachie, who initiated their collaboration; to Miss Cora Adamson, who spent many hours in making an accurate copy of a much-mutilated &st draft of the translation; and to the Yale University Library which gave access to its excellent collection of books on all aspects of the history of the sciences. The reader will share with the translators their obvious indebtedness to Mr. Carl P. Rollins, Mr. James W. Boyden, and the staff of the Printing-Office of the Yale University Press. The publication of this translation by the American Institute of Mining and Metallurgical Engineers has been made possible by a grant from the Seeley W. Mudd Memorial Fund, administered by a committee composed of Harvey S. Mudd, H. DeWitt Smith, and George Otis Smith. The translators are gratified that their work has been judged to fall within the scope of this Fund, which was established for the advancement of the sciences of mining and metallurgy by the encouragement of research and the dissemination of knowledge, and especially for the furtherance of such activities as might benefit the younger members of the profession. While Biringuccio's book would scarcely serve as a dependable text for the young mining student or metallurgist, it can give him a sense of his membership in a long-standing and honorable profession and enable him better to see his own work in true perspective. It is hoped that this English edition of a sixteenth-century Italian work will be read by the practicing metallurgist as well as by those who have already found pleasure in exploring the past of their profession. A man always feels more at home in a foreign country with men of his own craft than in his birthplace with those of different interests: As in space, so in time, and the modem metallurgist who may be unmoved by the literary and artistic Renaissance will quickly appreciate the spirit of that exciting period as he talks shop with Biringuccio on a visit to mine, smelter, forge, and foundry; as he sees in different forms the very furnaces and machines whose operation and response he knows so well; and as he discusses with this engineer of four centuries ago such topics as the best kinds of fuel or refractory for a given operation, and the importance of adequate supplies of power and material.

Jan 1, 1942

By P. E. Davidson

The management of solid waste is known to be a large and increasing problem in high-population areas throughout the world. It is not necessary here to add further definition to the nature and magnitude of the problem. Instead, it is the purpose of this paper to describe a new process, called the Andco-Torrax System, which will be of use in converting municipal solid waste into useful energy forms and a granulated slag by-product. The paper includes a description of the first commercial plant for the process.

Jan 1, 1977

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

A molten metal granulator was designed and fabricated at the U.S. Dept. of Energy, Albany Research Center, for granulation of precious metal-bearing alloys and slags. The system was designed to safely granulate a metal alloy at a temperature of up to 1,600°C at a rate of roughly 50 kg of alloy per minute. The primary water jet was supplied by a 18.6-kW, 600 liter per minute pump which provided approximately 600 kg of water per minute through the primary jet. Two 3.7-kW, 150 liter per minute auxiliary pumps provided additional wash water to wet the granulation trough through 4 secondary jets, which were placed at either side of the primary jet. The water supply was closed-loop, including a 37,850-liter supply tank and 22,710-liter recovery tank. Magnetic separators and particulate filters were included for collection of the finest fraction of the granulation product, which cleaned the water sufficiently for continuous recycle.

Jan 1, 2006

By P. Vijay Kumar

Phosphate minerals are conventionally concentrated by flotation process using soap or soap- light diesel oil emulsion as collector. Some plants use detergents such as sodium petroleum sulfonate or alfa olefin sulfonate to enhance efficiency of soap flotation. It is reported that urea a known hydrotrope enhances flotation efficiency of soap as efficiently as alfa olefin sulfonate or linear alkyl benzene sulfonate at bench scale tests. In the present study tri sodium citrate also a known hydrotrope is tested as promoter in the flotation of phosphate mineral from Eshidiya ore.

Sep 1, 2012

Jan 1, 1947

By J. M. Keane

The Solution Mining review arrived too late to appear in the May issue. Solution mining, in its broadest definition, includes all forms of leaching where a lixiviant solution is brought into contact with a metalliferous or non-metallic ore and the resulting pregnant solution is processed for recovery of the valuable soluble material. Technologies such as dump leaching, heap leaching, stope washing and in situ lixiviant solution injection and recovery fit into this definition of solution mining. A publication entitled the US Gold Industry (Dobra and Thomas) reflects the major impact that solution mining techniques have had on precious metal recovery. In 1989 (the last year for which statistics are available), the United States passed Australia to become the third largest gold producing country in the world after South Africa and the Soviet Union. It is estimated that when the final figures are in for 1990, the US will probably pass the Soviet Union in gold output. If the state of Nevada is ranked as a separate country, it will rank fourth in the world in gold production for 1990. A good proportion of this increase in gold production over the past few years can be attributed to the application of solution mining technology to low-grade, precious-metal-bearing material. Solution mining techniques have also made inroads in copper production. Many operations located at former underground mine sites employ in situ leaching as an adjunct to conventional dump and heap leaching practices.

Jan 1, 1991

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By James M. Schopf

Gilbert H. Cady (Senior Geologist, Head of Coal Division Emeritus, Illinois State Geological Survey, Ur-bans)— Those coal mining and preparation engineers and operators who read this article will probably be most concerned with those parts which deal with the applied aspects of coal petrology in the fields of mining and technology. Actually the two categories overlap to such a degree that they are essentially one. The article appears to suggest that there are two points of veiw in the field of applied coal petrology. From one viewpoint the interest is in the attributes of the various macerals (Fig. 4)—vitrinite, exinite, and inertinite—-in terms of utilization (when the coal is burned, coked, gasified, hydrogenated, etc.). From the other point of view, assuming that the macerals do possess individuality in behavior, interest attaches to the possibility that coal of a particular type (maceral composition) can be prepared by discriminating methods of preparation and blending. Most of the 29 items listed for mining and technology can be assigned to one or the other of these two categories. Somewhat the same simplicity that resides in the items of the proximate chemical analysis is desirable for the petrologic analysis. This simplicity appears to be fairly well achieved by the group maceral device provided mineral matter is also included. At present, without fully adequate experimental substantiation, the three types of material represented by the group macerals vitrinite, exinite, and inertinite are regarded as sufficiently different in composition and properties so that the preponderance of any one type gives the coal distinctive properties provided it is not too high in rank. This appears to be increasingly true with coals of decreasing rank from medium volatile bituminous coals downward. The article reflects the great emphasis placed on the technique of descriptive coal petrology in America. Such description has resulted in a good understanding of the nature of the fundamental variability in the physical composition of bituminous coals. Such understanding has been attained very largely by the thin section technique used in coal bed profile analysis introduced by R. Thiessen after the manner suggested by the data assembled in Table 11. In contrast, the group maceral concept of coal analysis in terms of the categories indicated on the left hand side of Fig. 4 is particularly useful for broken coal analysis and applied coal petrology, in which evaluation is largely based on quantitative concepts. It is inadequately emphasized in this article that although the Thiessen procedure is suitable for the purpose of petrologic description in which texture and orientation are of critical importance, it is less well adapted to the technological uses of applied coal petrology. No doubt those persons whose interest may have been aroused in the possibilities of more refined coal preparation by this and other recent contributions to the literature of coal petrology will understand that certain technical aspects of coal petrology, particularly in the field of descriptive petrology, are still a matter of some controversy among the coal petrologists, but they will also appreciate that Schopf has made an important contribution to the field of coal petrology in America by pointing out that such petrology requires consideration of disoriented or broken coal samples and that results are expressed less in descriptive terms than in quantitative values with respect to the four types of material composing coal—-vitrinite, exinite, inertinite, and mineral matter. Unfortunately because so much American coal petrology has been descriptive of the coal in the bed there is a dearth of literature on applied coal petrology. Research and experimental data in this field are greatly needed.

Jan 1, 1959

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950